DeWalt DW680 Manual

DeWalt Høvlemaskine DW680

Læs nedenfor 📖 manual på dansk for DeWalt DW680 (6 sider) i kategorien Høvlemaskine. Denne guide var nyttig for 44 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/6

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVOADVERTENCIA:

ANTES DE USAR EL PRODUCTO.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)

General Safety Instructions

WARNING! Read and understand all instructions. Failure to

follow all instructions listed below, may result in electric shock, fire

and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

•Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

•Keep bystanders, children, and visitors away while operating a power tool. Distractions

can cause you to lose control.

ELECTRICAL SAFETY

•Grounded tools must be plugged into an outlet properly installed and grounded in

accordance with all codes and ordinances. Never remove the grounding prong or

modify the plug in any way. Do not use any adaptor plugs. Check with a qualified elec-

trician if you are in doubt as to whether the outlet is properly grounded. If the tools

should electrically malfunction or break down, grounding provides a low resistance path to

carry electricity away from the user. Applicable only to Class I (grounded) tools.

•Double insulated tools are equipped with a polarized plug (one blade is wider than the

other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to

install a polarized outlet. Do not change the plug in any way. Double insulation elimi-

nates the need for the three wire grounded power cord and grounded power supply system.

Applicable only to Class II (double insulated) tools.

•Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

•Don’t expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

•Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of electric shock.

•When operating a power tool outside, use an outdoor extension cord marked “W-A”

or “W.” These cords are rated for outdoor use and reduce the risk of electric shock. When

using an extension cord, be sure to use one heavy enough to carry the current your product

will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size to use depending on cord length and

nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-

ber, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

Ampere Rating

More Not more AWG

Than Than

6 - 10 18 16 14 12

PERSONAL SAFETY

•Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication.

A moment of inattention while operating power tools may result in serious personal injury.

•Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,

clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and should also be avoided.

•Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

•Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

•Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

•Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

•Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss of

control.

•Do not force tool. Use the correct tool for your application. The correct tool will do the

job better and safer at the rate for which it is designed.

•Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with

the switch is dangerous and must be repaired.

•Disconnect the plug from the power source before making any adjustments, changing

accessories, or storing the tool. Such preventative safety measures reduce the risk of

starting the tool accidentally.

•Store idle tools out of reach of children and other untrained persons. Tools are dan-

gerous in the hands of untrained users.

•Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

•Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tool’s operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

•Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

SERVICE

•Tool service must be performed only by qualified repair personnel. Service or mainte-

nance performed by unqualified personnel could result in a risk of injury.

•When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow mainte-

nance instructions may create a risk of electric shock or injury.

Additional Safety Instructions for Planers

• To reduce the risk of injury, user must read and understand instruction manual before oper-

ating planer.

• Always wear eye protection and dust mask.

• Be sure the voltage agrees with specific data on the nameplate.

• Make certain that the switch is in the OFF position before connecting plug to a power source.

• Be sure to switch OFF immediately if tool is jammed in work.

• Be sure tool is set for correct depth before turning switch to ON.

• Be sure to use specified replacement parts only.

• Be sure tool is disconnected from power source when cleaning or making adjustments to

the tool.

• Be sure to maintain tool with care. Follow instructions for lubricating and changing

accessories.

• Stay alert – never operate the unit when tired or under the influence of drugs, alcohol, or

medication.

• Be sure to store tool in a clean dry place after disconnecting from power source.

• Do not use in dangerous environments. Do not use near flammable substances, in damp or

wet locations, or expose to rain.

• Be sure that the blades are mounted as described in the instruction manual and check that

all screws are firmly tightened before connecting unit to power source.

• Keep air vents unobstructed for proper motor cooling.

• DO NOT lay tool down on shoe when the blades are exposed. This can chip the blades.

• Keep side discharge chute unobstructed at all times.

• Never reach under the tool for any reason unless it is turned off and UNPLUGGED. BLADES

ARE EXPOSED AND EXTREMELY SHARP.

• Use this tool for working with wood and wood products only.

• Never operate without securely holding the front handle.

• Always operate planer with two hands.

• Planer blades are extremely sharp. Handle with great care.

• Clean out your tool often, especially after heavy use.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with approved

safety equipment, such as those dust masks that are specially designed to filter out microscopic

particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some conditions and

duration of use, noise from this product may contribute to hearing loss.

• The label on your tool may include the following symbols. The symbols and their definitions

are as follows:

V........................volts A..........................amperes

Hz......................hertz W ........................watts

min ....................minutes ......................alternating current

..................direct current n

o........................no load speed

......................Class II Construction …/min..................revolutions per minute

......................earthing terminal ........................safety alert symbol

SAVE THESE INSTRUCTIONS

COMPONENTS (Figure 1)

DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286

The following are trademarks for one or more D WALT power tools: the yellow and black color scheme; theE

“D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of

lozenge-shaped humps on the surface of the tool.

DW680

3-1/4" (82mm) Heavy Duty Planer

Raboteuse à service intensif de 82 mm (3-1/4 po)

Cepillo de 82 mm (3-1/4") para trabajo pesado

A. Trigger switch

B. Lock-on button

C. Depth adjustment knob/

front handle

D. Switch Handle

E. Shoe

F. Rabbet fence (not shown)

G. Rabbet fence adjustment knob

H. Chip discharge chute

OPERATION

Motor

Be sure your power supply agrees with the nameplate markings. 120 volts AC means your

tool may be operated only with alternating current and with direct current.never

Voltage decrease of more than 10% will cause loss of power and overheating. All DEWALT tools

are factory tested; if this tool does not operate, check the power supply.

Switch (Figure 1)

CAUTION: Check that the tool is not locked ON before connecting it to a power supply. If

the trigger switch is locked ON when the tool is connected to the power supply, it will start

immediately. Damage to your tool or personal injury may result.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Høvlemaskine
Model:	DW680
Bredde:	290 mm
Højde:	170 mm
Vægt:	3200 g
Produktfarve:	Black,Yellow
Indgangseffekt:	800 W
Udgangseffekt:	350 W
Strømkilde:	Vekselstrøm
Soft greb:	Ja
Tomgang:	15000 rpm
Planlægningsbredde (maks.):	82 mm
Chips, tykkelse (maks.):	2.5 mm
Falsningsdybde:	12 mm