DeWalt DW920K-2 Manual

DeWalt bore DW920K-2

Læs nedenfor 📖 manual på dansk for DeWalt DW920K-2 (7 sider) i kategorien bore. Denne guide var nyttig for 22 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/7

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

DW920

7.2 Volt Heavy Duty Cordless Screwdriver

Tournevis 7,2 volt sans fil de service intensif

Destornillador de 7,2 volt para trabajo pesado

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,

CALL US TOLL FREE AT:

1-800-4-DEWALT (1-800-433-9258)

General Safety Rules – For All Battery Operated Tools

WARNING! Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-

dents.

• Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or

fumes.

• Keep bystanders, children, and visitors away while operating a power tool. Distrac-

tions can cause you to lose control.

ELECTRICAL SAFETY

• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat, oil,

sharp edges or moving parts. Replace damaged cords immediately. Damaged cords may create

a fire.

• A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery. A charger that may be suit-

able for one type of battery may create a risk of fire when used with another battery.

• Use battery operated tool only with the specifically designated battery pack. Use of

any other batteries may create a risk of fire.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medica-

tion. A moment of inattention while operating power tools may result in serious personal

injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,

clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be

caught in moving parts.

• Avoid accidental starting. Be sure switch is in the locked or off position before insert-

ing battery pack. Carrying tools with your finger on the switch or inserting the battery pack

into a tool with the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and bal-

ance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,

hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to a loss

of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the job

better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tool. Such pre-

ventative safety measures reduce the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are dan-

gerous in the hands of untrained users.

• When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a con-

nection from one terminal to another. Shorting the battery terminals together may cause

sparks, burns, or a fire.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,

with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced before

using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may create a risk of injury when used on

another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or mainte-

nance performed by unqualified personnel may result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in the

Maintenance section of this manual. Use of unauthorized parts or failure to follow

Maintenance Instructions may create a risk of shock or injury.

Additional Safety Rules

• Hold tool by insulated gripping surfaces when performing an operation where the

tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal

parts of the tool “live” and shock the operator.

•When working on a ladder or on scaffolding be sure to lay the tool down on its side

when not in use. Some tools with large battery packs will stand upright but may be easily

knocked over.

• The label on your tool may include the following symbols.

V....................volts A ............amperes

Hz..................hertz W ..........watts

min ................minutes ..........alternating current

..............direct current ..........Class II Construction

no ..................no load speed …/min ....revolutions or reciprocation per minute

..................earthing terminal ..........safety alert symbol

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other reproduc-

tive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter out

microscopic particles.

Important Safety Instructions for Battery Packs

The battery pack is not fully charged out of the carton! First read the safety instruc-

tions below. Then follow charging notes and procedures.

READ ALL INSTRUCTIONS.

• Do not incinerate the battery pack even if it is severely damaged or is completely worn out.The

battery pack can explode in a fire.

• A small leakage of liquid from the battery pack cells may occur under extreme usage or temper-

ature conditions. This does not indicate a failure. However, if the outer seal is broken and this

leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 minutes

and seek immediate medical attention. (Medical note: The liquid is 25-35% solution of potassi-

um hydroxide.)

• Do not carry extra battery packs in aprons, pockets, or tool boxes along with other metal objects.

Battery pack could be short circuited causing damage to the battery pack and possibly causing

severe burns or fire.

• Charge the battery packs only in DEWALT chargers.

•NOTE:The batteries in your battery pack are the nickel–cadmium type. Cadmium is considered

to be a toxic material by the Environmental Protection Agency. Before disposing of damaged or

worn out Nickel–Cadmium battery packs, check with your state Environmental Protection Agency

to find out about special restrictions on the disposal of these battery packs or return them to a

DEWALT certified service center for recycling.

•DO NOT store or use the tool and battery pack in locations where the temperature may reach or

exceed 105°F (such as outside sheds or metal buildings in summer).

DANGER: Never attempt to open the battery pack for any reason. If battery pack case is

cracked or damaged, do not insert into charger. Danger of electric shock or electrocution.

Damaged battery packs should be returned to service center for recycling.

Installing and Removing the Battery Pack

NOTE: Make sure your battery pack is fully charged.

To install the battery pack into the tool handle, align the base of the tool with the notch

inside the tool’s handle (FIG. 2) and slide the battery pack firmly into the handle until you hear

the lock snap into place as shown in FIG. 3.

To remove the battery pack from the tool, press the release buttons and firmly pull the bat-

tery pack out of the tool handle. Insert it into the charger as described in the charger section

of this manual.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-

cadmium battery (or battery pack) indicates that the costs to recycle the battery

(or battery pack) at the end of its useful life have already been paid by D EWALT.

In some areas, it is illegal to place spent nickel-cadmium batteries in the trash or

municipal solid waste stream and the RBRC program provides an environmen-

tally conscious alternative.

RBRC in cooperation with DEWALT and other battery users, has established programs in the

United States to facilitate the collection of spent nickel-cadmium batteries. Help protect our

environment and conserve natural resources by returning the spent nickel-cadmium battery to

an authorized DEWALT service center or to your local retailer for recycling. You may also con-

tact your local recycling center for information on where to drop off the spent battery.

Important Safety Instructions for Battery Chargers

SAVE THESE INSTRUCTIONS - This manual contains important safety instructions for

DEWALT battery chargers.

• Before using battery charger, read all instructions and cautionary markings on battery char-

ger, battery and product using battery.

CAUTION:To reduce the risk of injury, charge only DEWALT nickel cadmium rechargeable

batteries. Other types of batteries may burst causing personal injury and damage.

CAUTION: Under certain conditions, with the charger plugged in to the power supply, the

exposed charging contacts inside the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

DANGER: 120 volts present at charging terminals. Do not probe with conductive objects.

Danger of electric shock or electrocution.

WARNING: Don’t allow any liquid to get inside charger. Electric shock may result.

• The charger and battery pack are specifically designed to work together. attempt toDO NOT

charge the battery pack with any chargers other than the ones in this manual.

• These chargers are not intended for any uses other than charging DEWALT rechargeable batteries.

Any other uses may result in risk of fire, electric shock or electrocution.

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

Questions? See us in the World Wide Web at www.dewalt.com

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	bore
Model:	DW920K-2

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DW920K-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bore DeWalt Manualer

14 Oktober 2024

21 September 2024

15 September 2024

11 September 2024

DeWalt DWD216G Manual

6 September 2024

DeWalt DCD445 Manual

6 September 2024

DeWalt DC987-XE Manual

4 September 2024

DeWalt DW922K2 Manual

4 September 2024

DeWalt DCD932 Manual

4 September 2024

DeWalt D21717 Manual

4 September 2024

bore Manualer

Nyeste bore Manualer

Einhell BM-G1100 E Manual

14 Oktober 2024

Sun Joe 24V-DDK-LTX-PNK Manual

14 Oktober 2024

Rupes BH 252R Manual

13 Oktober 2024

Makita DHR263ZJ Manual

12 Oktober 2024

Makita HP2070 Manual

12 Oktober 2024

Makita DDA350RFJ Manual

7 Oktober 2024

Einhell TE-ID 750/1 E Manual

7 Oktober 2024

Makita HP332D Manual

7 Oktober 2024

Makita M6501 Manual

6 Oktober 2024

Metabo BH 18 LTX BL 16 Manual

6 Oktober 2024