Digital Watchdog MegaPix DWC-MB72WI4T Manual

Digital Watchdog Overvågningskamera MegaPix DWC-MB72WI4T

Læs nedenfor 📖 manual på dansk for Digital Watchdog MegaPix DWC-MB72WI4T (2 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
3. Loosen the pan and tilt screw
at the base of the camera’s
bracket to adjust the cameras
view and position.
Reset
button
DWC-MB72Wi4T
Quick Start GuideQuick Start Guide
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00 AM 8:00 PM EST, Monday through Friday
digital-watchdog.com
Resetting the camera: To reset the camera, use the tip of a paper clip
or a pencil and press the reset button. Pressing the button for ve (5)
seconds will initiate a camera-wide reset of all the settings, including
network settings.
WHAT’S IN THE BOX
Quick setup
and download
guides
1 set
Screws and
plastic anchors
4pcs
1 set
Mounting
template 1Hex Allen
wrench 1
Waterproof
cap 1 set
STEP 1 PREPARING TO MOUNT THE CAMERA
STEP 2 CABLING THE CAMERA TO THE POWER
1. The mounting surface must withstand ve times the camera weight.
2. Do not let the cables get caught in improper places or the electric line
cover can be damaged. This may cause a short or fire.
3. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.
Pass the wires through the bracket and make all necessary connections.
1. NETWORK CONNECTIONS - If you are using a PoE switch, connect
the camera using an Ethernet cable for both data and power.
2. NETWORK CONNECTIONS - If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
Power requirements Power consumption
DC 12V, PoE (IEEE 802.3af Class 2)
Adapter not included.
DC12V: max 4.5W
PoE: max 6.0W
1. Attach the camera’s bracket to the mounting surface using the
included four (4) screws.
2. To use the camera’s waterproof wiring:
a. Install the LAN cable into .
b. will be assembled
to with a 1/4 turn.
c. Thread tightly to .
a
b
c
STEP 3 INSTALLING THE CAMERA
a
a
b
bc
NOTE: To ensure moisture seal, make sure the o-ring is in place
between and . In extreme environments use of an
outdoor rated sealer is recommended.
ab
NOTE: When using the waterproof cap, crimp the RJ45 connector
after passing the cable through the waterproof cap.
Default Login Information: admin | admin
When logging into the camera for the first time, you will be prompted
to set up a new password. You can set the new password using the
DW® IP Finder™ software or directly from the camera’s browser menu.
Attention: This document is intended to serve as a quick reference for the initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click . All supported materials, including manuals ‘Search’
and quick start guide (QSGs) will appear in the results.
Mounting template
Pan / tilt
screw


Produkt Specifikationer

Mærke: Digital Watchdog
Kategori: Overvågningskamera
Model: MegaPix DWC-MB72WI4T

Har du brug for hjælp?

Hvis du har brug for hjælp til Digital Watchdog MegaPix DWC-MB72WI4T stil et spørgsmål nedenfor, og andre brugere vil svare dig




Overvågningskamera Digital Watchdog Manualer

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer