Dormakaba Cencon Gen2 Manual


Læs nedenfor 📖 manual på dansk for Dormakaba Cencon Gen2 (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
P/N 2088.0310 Rev. B • 11/12 © copyright 2010-2012 Kaba Mas LLC
Page 1 of 2
CENCON GEN2
Cencon Gen2 Lock to Cencon 4 Software
(Serial to USB) Interface Kit (P/N 201186)
Kit Contents:
A. Interface Box
B. Mini-USB Cable (Cencon PC to Interface Box)
C. 10-pin Serial Cable (Gen2 Lock to Interface Box)
Compatibility:
The Interface Kit is designed for use with Cencon Generation 2 (Gen2) locks
in conjunction with the Cencon 4 software, version 4.0.5 and higher.
Purpose:
The Interface Kit allows the Gen2 lock to be programmed or data to
be retrieved from the lock via a direct communication to the Cencon 4
software. Rather than transporting keys from the PC to the lock key reader
and back, the Interface Kit allows a direct wired connection from the 10-pin
serial connector on the back cover of the Gen2 locks with a USB port on
the Cencon 4 PC. Aside from the time-saving aspect of using the Interface
Box, another benefit is the unique reporting capability provided by using
this device. The Lock Status Report shows various items such as bolt status and temperature. A full Lock Audit (i.e., all available audit
records in the lock) can be obtained via the direct link through the Interface Box. This is an improvement over the traditional method of
retrieving audit records with the red SA key where the number of records may be truncated due to the limitation of the memory in
the key.
Direct “Serial Connect” operations using the Interface Kit include:
Activate FLM, Route, and Bank modes (including setting initial Bank mode users)
NOTE: Activating a Mode will require that the change key be inserted into the lock back cover. (See photo below.)
Change the Access Requirement type for a mode between Single
and Dual
View, Add, or Delete Bank mode users
Close an FLM or Route mode open call on the software (lock powers
up “IPI”)
Resynchronize the software with the FLM or Route mode of the lock
Resynchronize the User List in software for Bank Mode with the lock
Set Time Delay and Open Time Window for Bank Mode
Shelve FLM, Route, and Bank modes
Set Lock Clock and Time Zone Daylight Savings Time Table
View Lock Status Report and Lock Audit Report
Please refer to the Cencon 4 Reference Manual (found at http://www.kaba-
mas.com/pdf/technical/2071.127Cencon4RefManA.pdf or on the install
CD), Section 3.1.7 “Lock Operations with Serial Connect”, for details on
each of these operations.
Driver Install instructions for the Cencon Interface Box:
WARNING: DO NOT plug in the USB device before installing the driver.
The PC that is running Cencon 4 should be able to obtain a connection to the internet to download this driver. If the PC does not have
a connection, save the driver to a disc or USB drive to transfer it to the Cencon 4 PC.
The Interface Kit uses FTDI Device FT232R. A copy of the driver installation for the device is available at
http://www.ftdichip.com.
InstructIon sheet
A.
B.
C.
Interface Kit parts.
Always wear a grounding strap when handling the back cover.


Produkt Specifikationer

Mærke: Dormakaba
Kategori: Ikke kategoriseret
Model: Cencon Gen2

Har du brug for hjælp?

Hvis du har brug for hjælp til Dormakaba Cencon Gen2 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Dormakaba Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024