Electro Harmonix Hot Tubes Manual


Læs nedenfor 📖 manual på dansk for Electro Harmonix Hot Tubes (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
1
HOT TUBES
Congratulations on your purchase of the Hot Tubes overdrive, a faithful reissue of the
original 1970s Electro-Harmonix classic, now in a compact pedalboard-friendly
enclosure. Since its initial release in 1978, countless musicians have prized the
scorching tube amp simulation the Hot Tubes delivers. They consider the original Hot
Tubes to be indispensable, so it is rarely available on the vintage market. Now there
is no need to search. The Hot Tubes reissue gives you the exact same tone and drive
as the original.
- CONTROLS -
OVERDRIVE Knob – Controls the amount of input gain and distortion delivered by
the Hot Tubes. As you turn OVERDRIVE clockwise, the distortion ranges from mild
tube-like breakup to saturated distortion.
TONE Knob – Creates a range of tones from warm bass to bright treble as the knob
is turned clockwise.
VOL Knob – Sets the output volume of the HOT TUBES.
TONE Switch – When this switch is set to OFF, the HOT TUBES Tone knob is
disabled, resulting in a more powerful, direct tone. When the TONE SWITCH is set to
ON, the TONE KNOB behaves normally.
FOOTSWITCH and LED – The footswitch selects whether the HOT TUBES is
engaged or in true bypass mode. When the effect is engaged, the LED will be lit.
INPUT Jack – This ¼” jack is the audio input for the HOT TUBES. The input
impedance is 100k .
AMP Jack – This ¼” jack is the audio output from the HOT TUBES. The output
impedance depends on the VOLUME setting, ranging from 350 to 3k . Ω Ω
9V Power Jack – The HOT TUBES can run off of a 9V battery or you can use an
optional 9VDC AC Adapter capable of delivering at least 50mA to the 9V power jack.
The AC Adapter must have a center negative plug. The battery may be left in or
taken out when using an AC Adapter. The Hot Tubes draws 18mA at 9VDC.
- CHANGING THE BATTERY -
To change the 9-volt battery, you must remove the 4 screws on the bottom of the
HOT TUBES. Once the screws are removed, you can take off the bottom
plate and change the battery. Please do not touch the circuit board while the bottom
plate is off or you risk damaging a component.


Produkt Specifikationer

Mærke: Electro Harmonix
Kategori: Ikke kategoriseret
Model: Hot Tubes

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Hot Tubes stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Electro Harmonix Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024