Electro Harmonix Switchblade+ Manual


Læs nedenfor 📖 manual på dansk for Electro Harmonix Switchblade+ (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
SWITCHBLADE+
Deluxe Channel Selector
Congratulations on your purchase of the Electro-Harmonix ! With a fully SWITCHBLADE+
passive audio path and active LED indication, the provides a simple and SWITCHBLADE+
versatile interface for routing your signal.
Controls – –
A/B Footswitch (LED) Press this switch to route the input signal to either OUT A (Red
LED) or OUT B (Green LED).
A+B Footswitch (LED) Press this switch to route the input signal to both OUT A and
OUT B. When A+B is engaged (Red LED), the A/B Footswitch has no effect on the signal
path.
– – I/O
INPUT Connect the output of your instrument or another effects pedal to this jack.
TUNER Connect this jack to the input of a tuner device or another effects pedal. This
jack is hardwired to the INPUT jack and provides a direct output regardless of the state of
the unit.
OUT A Connect this jack to the input of an amplifier or the input of another effects
pedal. Depending on the state of the A/B and A+B controls, this jack will output either the
direct input signal or no signal. When the A/B LED is lit red or the A+B LED is lit up, OUT A
is selected.
OUT B Connect this jack to the input of an amplifier or the input of another effects
pedal. Depending on the state of the A/B and A+B controls, this jack will output either the
direct input signal or no signal. When the A/B LED is lit green or the A+B LED is lit up, OUT
B is selected.
Power -
The can be powered by a 9V battery or a 9VDC battery eliminator SWITCHBLADE+
capable of delivering at least 16mA. The optional 9V power supply from Electro-Harmonix
is 9.6DC-200BI (same as used by Boss® & Ibanez®) 9.6 Volts DC 200mA. The power
supply must have a barrel connector with center negative.
The SWITCHBLADE+ can also operate without power, since the audio path is fully
passive. With no power, however, the LED indication will not function.
When A+B is engaged, the input impedance at the INPUT jack is equal to 50kΩ in parallel
with the combined input impedances of the devices connected to the TUNER, OUT A, and
OUT B jacks. When A+B is not engaged, the input impedance at the INPUT jack is equal
to 100kΩ in parallel with the combined input impedances of the devices connect to the
TUNER jack and OUT A or OUT B.


Produkt Specifikationer

Mærke: Electro Harmonix
Kategori: Ikke kategoriseret
Model: Switchblade+

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Switchblade+ stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Electro Harmonix Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024