Elite Screens VMAX Plus 4 VMAX200XWS Manual
Elite Screens
Projektionslærred
VMAX Plus 4 VMAX200XWS
Læs nedenfor 📖 manual på dansk for Elite Screens VMAX Plus 4 VMAX200XWS (8 sider) i kategorien Projektionslærred. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/8
1
Rev.010512-AS
www.elitescreens.com info@elitescreens.com
Electric Motorized Projection Screen
VMAX PLUS 4 SERIES
User’s Guide
2
Rev.010512-AS
www.elitescreens.com info@elitescreens.com
Make sure to read this user’s guide and follow the procedure below.
Cauon: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black
Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved
changes or modicaons (except for cung the power cord for hardwire installaons) to this unit are
prohibited and will void your warranty. For more informaon, please contact our Technical Support
Department at (877) 511-1211 Ext. 604.
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not
recommended by the manufacturer.
Handle the unit carefully during transportaon to avoid any damages.
To ensure safe and reliable operaon, direct connecon to a properly grounded power
source is advised.
The power outlet supplying power to the unit should be close to the unit and easily
accessible.
Do not install the unit on uneven or inclined surfaces.
Do not put heavy objects on the power cord and posion it properly to avoid creang a
trip obstacle.
Never overload the power cord to prevent an electric shock or re due to a loose
contact or a short circuit.
There are not user serviceable parts in this unit. Do not aempt to disassemble this unit
by yourself. No one except authorized technicians can open and make repairs to this
unit.
Make sure the power source this unit is connected to has a connuous power ow.
If there is need to use an extension cord, make sure the cord has an equal rang as the
appliance to avoid overheat.
Do not handle the power plug when your hands are wet or your feet are in contact with
water.
Do not use this unit under the following circumstances.
Disconnect the power cord under the condions of heavy rain, wind, thunder or
lightning.
Avoid direct Sunshine, rain shower and moisture.
Keep away from re sources and high temperature to prevent this device from
overheang.
Cut o the power supply rst before transportaon or maintenance.
Fully disconnect from the power supply when the unit is not in use for a long period of
me, as should be done with any other electric household appliance.
To avoid possible injury and/or an electric shock, do not aempt to use the screen if
there is obvious damage or if there are any evident broken parts.
Important Safety & Warning Precautions
3
Rev.010512-AS
www.elitescreens.com info@elitescreens.com
Due to various installaon environments, the instrucons provided in this user’s guide are for
reference only. Please consult a professional installaon company for further installaon and
safety advice. The installer must insure that proper mounng hardware is used to provide
adequate strength suitable for the installaon. Elite Screens is not liable for any faulty
installaons.
The Screen’s Top Black Drop is already set to its maximum drop distance. There is extra top black NO
drop in the roller. Please be aware of this as it will void the limitaon of your warranty.
Individual modicaons to this product are prohibited and will void the warranty with the
manufacturer. Please contact Elite Screens Customer Service for any quesons.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful interference in a residenal
installaon. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that the interference will not occur on a parcular installaon. If this
equipment causes harmful interference to radio or television recepon, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing the interference.
Increase the separaon between the screen and the device’s receiver.
Connect the equipment into a dierent power outlet other than the device.
1. Carefully unpack the screen.
2. Always handle the screen in a leveled posion on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with
foreign parcles such as dust, sawdust, and/or liquids.
Regardless of the mounng method, the screen should be securely supported so that the vibraon or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installaon locaon.
Installation Warning
Pre-Installation
NOTE
4
Rev.010512-AS
www.elitescreens.com info@elitescreens.com
Please make sure all accessories below are included before proceeding.
Red+ Green-
A. B. C. D.
Infrared Remote Radio Frequency 12 Volt Trigger 3 Way Wall Switch
D. E. F.
Infrared Eye Receiver AAA Batteries Bubble Level
Accessories for VMAX Plus 4 Series
5
Rev.010512-AS
www.elitescreens.com info@elitescreens.com
Please consult a professional installer. Elite Screens is not liable for any faulty installaons.
1. Select the installaon locaon for your screen. Ensure that it is within reasonable proximity
from your power source.
2. Elite Screens provides a built-in suspended ceiling mount bracket for the VMAX PLUS 4. The
professional installer would need to provide any hardware and the safest way to install this
screen.
1. Built in installaon bracket.
2. Built-in 5-12 volt trigger port (RJ-45) for 12 Volt Trigger, 3 Way Wall Switch and IR Eye Receiver.
3. Easy access to the motor and circuit board.
Installation Instructions
6
Rev.010512-AS
www.elitescreens.com info@elitescreens.com
For addional informaon, please contact Elite Screens at techsupport@elitescreens.com
1. If your screen does not move, please check the power supply. The screen will understandably
not move without power.
2. Make sure the power cord is rmly plugged to the power outlet.
3. Make sure that all cable connecons are secure.
4. If the screen works well with the line switch but not with the remote control, please make sure
the remote controls have fresh baeries. Change the baeries every 6 months to ensure proper
operaon of the remotes.
1. Q: Why does my screen no longer funcon?
A: Make sure your wall plug has power and that the screen is properly plugged. The fuse on the
screen will also need to be checked. Please contact techsupport@elitescreens.com for the
locaon. The tubular motor in this screen is equipped with a thermal relay. This feature will
automacally shut o the screen in the event of the motor becoming too hot. This will prevent
the motor from overheang. If you should experience this, please let the screen’s temperature
decrease for 10-15 min. before usage.
2. Q: How is the screen material cleaned?
A: The screen material can be cleaned with mild soap and water.
3. Q: What type of baeries do the remote controls require?
A: The IR and RF remote controls use AAA alkaline baeries.
4. Q: Can you manually pull down the screen?
A: No, manually pulling down the screen will damage the electronic motor rolling system and
void your warranty.
5. Q: How could I setup my Screens IR receiver to work with my learning remote control system
Do you have any IR codes I can use to achieve this?
A: Our IR remote controls have been evaluated and entered in to the databases of some
universal remote control manufacturers. Please contact the manufacturer of your remote to
inquire about your remotes ability to funcon with ours. If they have not evaluated our remote
control then the following list of Binary codes will be used for most remote setups.
For Spectrum, VMAX2, VMAX PLUS 3 & 4, Home2 and CineTension 2 Series
Up: 1111 0000 0001
Stop: 1111 0000 0010
Down: 1111 0000 0100
Troubleshooting & FAQ’S
7
Rev.010512-AS
www.elitescreens.com info@elitescreens.com
*Measurement dimensions are intended as a reference only and subject to change without noce. Note: Data Error may be ±1"
VMAX PLUS 4 Series Dimension Table
Produkt Specifikationer
Mærke: | Elite Screens |
Kategori: | Projektionslærred |
Model: | VMAX Plus 4 VMAX200XWS |
Har du brug for hjælp?
Hvis du har brug for hjælp til Elite Screens VMAX Plus 4 VMAX200XWS stil et spørgsmål nedenfor, og andre brugere vil svare dig
Projektionslærred Elite Screens Manualer
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
Projektionslærred Manualer
- Projektionslærred Pyle
- Projektionslærred Kodak
- Projektionslærred Optoma
- Projektionslærred Da-Lite
- Projektionslærred Elite
- Projektionslærred NEC
- Projektionslærred AV:link
- Projektionslærred Draper
- Projektionslærred Vestel
- Projektionslærred Oregon Scientific
- Projektionslærred GPX
- Projektionslærred Duronic
- Projektionslærred Elite ProAV
- Projektionslærred Luxburg
- Projektionslærred EluneVision
- Projektionslærred Celexon
- Projektionslærred Lumene
- Projektionslærred Stewart
- Projektionslærred Avers
- Projektionslærred Instaal
- Projektionslærred KHOMO GEAR
- Projektionslærred EPV
Nyeste Projektionslærred Manualer
1 Oktober 2024
26 September 2024
22 September 2024
19 September 2024
6 September 2024
5 September 2024
5 September 2024
4 September 2024
4 September 2024
4 September 2024