Elro SX-201I Manual

Elro Dørklokke SX-201I

Læs nedenfor 📖 manual på dansk for Elro SX-201I (1 sider) i kategorien Dørklokke. Denne guide var nyttig for 41 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

Volume

Mode Light

Reset

CR2032 3V

Lithium Battery

Remove

Isolation

Strip

Wire Free Rechargeable Door Chime Kit SX-201i/201W

100m

1 2

Door Chime

• The rechargeable batteries are installed; charge the

batteries fully before use.

• Use a small pin insert into the small hole marked

“Reset” and press. It will beep twice to indicate that it

is ready for the new operation code registration

(Please see Digital Code Set Up).

• Place the Chime unit onto the charger, the LED on the

charger will light up in Red to indicate that the batteries

are charging.

• When the LED on the charger lights up in Green colour,

it is indicating that the charging procedure is completed

and the chime unit is ready to use.

3 4

5 6

Door Chime Installation

Place the Door Chime unit on any table top

or flat surface, then it is ready to use.

Adjust the volume

Use a small flat screwdriver to adjust the sound volume.

Mode Selector

Press the mode selector to select the following functions:

a)Sound and Light b) Light Only c) Sound Only

Low Battery Indicator

Red LED indicator on the top of Door Chime unit will

flash when the batteries are running low to the point

that they need to recharge. Simply place the chime unit

onto the charger to recharge the batteries.

Charger

Connect the charger with A/C-D/C 9volt 300mA adaptor

(Byron model SX-36 – included), then plug the adaptor

into any convenient wall socket, after then it is ready to

use.

Push Button unit

Power: 1 x 3volt Lithium battery (CR2032 - included)

Door Chime unit

Power: 3 x 1.2volt “AA” Ni-MH batteries (included)

Melody Selection

There are 8-melodies for selection -

1) Tubular 3-notes

2) Big Ben

Additional Byron “SX” range products can be purchased for compatibility.

Digital Code Set Up

The Door Chime kit is equipped with an advanced random and self-learning operation coding ability

therefore no setting is needed. Read the following instructions before use.

1. First time operation:

After battery installation on the Push Button, then reset the Door Chime unit by insert a small pin into the

small hole marked “Reset” on the back of chime unit and press, the door chime unit will beep twice to

indicate that it is ready for new operation code registration. Press the Push Button once and it will generate

a new operation code randomly and send a wireless signal to the Door Chime unit, the door chime will

sound to indicate that a new operation code is registered and memorised.

2. Interference from similar unit operating nearby:

a) Simply remove the battery from the Push Button and rest for 10 seconds, after then insert a small pin

into the small hole marked “Reset” on the back of chime unit and press, this will erase the memory.

The Door Chime unit it will give 2-beeps to indicate that it is ready for the new code registration.

b) Re-insert the battery into the Push Button, then press the Push Button once, it will generate a new

operation code randomly and send a wireless signal to the Door Chime and it will sound to indicate that a

new operation code is registered and memorised.

3. Front and back door Bell Push operation:

a) Remove the battery from the Push Buttons (Front & Back Door) and rest for 10 seconds, after then reset

the Door Chime units and this will erase the memory. The Door Chime unit it will give 2-beeps to indicate

that it is ready for the new code registration.

b) Insert the battery into the Push Buttons (Front & Back Door).

c) Press the front door Push Button once, it will generate a new operation code randomly and send a

wireless signal to the door chime unit and it will sound to indicate that a new operation code is registered

and memorised.

d) After, (within 2 minutes) press the back door Push Button once, it will generate a new operation code

randomly and send a wireless signal to the door chime unit and it will sound to indicate that a new

operation code is registered and memorised. The door chime unit has ability to memorize both operation

codes and will only work with it.

e) Test to ensure correct operation before final installation.

Door Chime Operation

The function (Mode) selector is located at the back of the unit; press the button to select one of the following

functions to operate the chime unit accordingly:

a) Sound and Light: The Door chime will sound as well as the Super Bright LED Light will flash to maximizing

attention

b) Light Only: The Super Bright LED Light on the Door Chime unit will flash

c) Sound Only: Door Chime unit will sound

The door chime will start operate at “Sound Only” function initially.

For repeat sound, press the button again. Holding the button in will repeat the sound.NOT

Flashing Light Pattern

When (a) Sound + Light OR (b) Light Only mode is selected, press the flashing light pattern button “Light” at

the back of the chime unit to select the operation in the following pattern:

1) Sound + Light mode - When the door chime sound, it will flash in following pattern:

a) Slow flashing for 5 seconds

b) Fast flashing for 5 seconds

Byron No.SX201i/201W Size: A4 Date: 6 May 2008

Melody Selector

Volume

Mode Light

Reset

Mode Light

Signal Sent Indicator Light

Low Batt

Volume

c) Flashing intermittent, 2 seconds “On”, 1 second “Off” and 2 seconds “On” again

2) Light Only mode - The door chime will flash in following pattern without the chime sound:

a) Slow flashing for 10 seconds

b) Fast flashing for 10 seconds

c) Flashing intermittent, 2 seconds “On”, 1 second “Off” and 2 seconds “On” again for 2 times.

Door Chime Unit – Charging Procedure

1. Connect the charger with A/C-D/C 9volt 300mA adaptor (Byron model SX-36 - included), then plug the

adaptor into any convenient wall socket, after then the charger is ready to use.

2. Place the Chime unit on to the charger, the LED on the charger will light up in “Red” to indicate that the

batteries are charging.

3. When the LED on the charger lights up in “Green” colour, it is indicating that the charging procedure is

completed and the chime unit is ready to use.

Note: Charge the batteries fully before use.

Important

1. Do not mount either unit close to fireplace or expose to high temperatures.

2. Do not expose the Door Chime unit to direct sunlight or moisture

3. Always use alkaline battery. Please dispose of old, defective batteries in an environmentally friendly manner

in accordance with the relevant legislation.

4. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.

5. The unit should not be exposed to dripping or splashing and no objects filled with liquids, such as vases,

should be placed on the unit.

6. Replace only with the same or equivalent type of battery that is recommended by the CAUTION:

manufacturer.

7. Make sure batteries are installed correctly as per the internal markings.CAUTON:

8. Danger of explosion if battery is incorrectly installed or replaced.CAUTION:

9. IMPORTANT: There are no serviceable parts in the units, do not attempt to repair it.

User Hints

If the door chime unit does not sound, please check the following:

a) Flat batteries in either Push Button or Door Chime units - change the Push Button battery and re-charge the

Door Chime batteries.

b) Wrong battery polarity in either Push Button - re-insert the batteries.

c) Push Button and Door Chime units are not on the same operation codes - reset the code (see digital code

set up).

d) Units are out of range - Operate the Chime unit within the operation range.

e) Reset the door chime unit if it does not sound, or has sound distortion.

Specification

Operating Temperature: -10C - +40C

Operating Distance: 100metre (330ft approx. - in open field & at suitable condition)

Selectable Tone: Total Eight (8) melodies available

Selectable Digital Code: Total two hundred fifty six (256) possible digital codes

“Type R2 Device - device where the sound output is created by the

initial operation of the control and where the period of sound

output continues for the designed duration irrespective of

condition of the control.”

433MHz

R&TTE

APPROVED

CH Byron Electrical United Kingdom. www.chbyron.com

CH Byron Electrical Ltd

Byron House

34 Sherwood Rd, Astonfield

Bromsgrove, B60 3DR

Tel: 0845 2301231

e: support@chbyron.com

w: www.chbyron.com

Push Button

• Open up the push button by pushing in the tab at the

bottom of the push with a small flat screwdriver.

• Remove the isolation strip from the battery

compartment then it is ready to use.

• When replacing the battery, ensure the battery polarity

matches the internal markings (“+” facing upwards),

then press the battery down so that it is sitting firmly

in its compartment.

Digital Code Set Up

• Press the Push Button once, a new operation code is

generated randomly and sent to the Door Chime unit.

• The Door Chime will sound to indicate that a new

operation code is registered and memorised.

Push Button Installation

• Using the holes on the back of push button as a

template, mark the fixing position for the unit.

• Drill holes and fit wall plugs and secure the push button

unit to the wall with screws.

• Do not mount it on any metal surface or UPVC door

frame.

Operation

• Press the button on the Push Button unit once, it sends

a wireless signal to the Door Chime and your Door

Chime unit will sound.

• Operate the Door Chime unit within the operation range,

test it before final installation.

Melody Selection

Press the melody selector once to select a melody as

your door chime sound. There is a total of 8 melodies

for selection:

1) Tubular 3-notes

2) Big Ben

3) Tubular 2-notes

4) Solo

Additional Byron “SX” range products can be purchased

for compatibility.

5) Tubular Scare

6) Clarinet

7) Saxophone

8) Morning Dew

3) Tubular 2-notes

4) Solo

7) Saxophone

8) Morning Dew

5) Tubular Scare

6) Clarinet

Produkt Specifikationer

Mærke:	Elro
Kategori:	Dørklokke
Model:	SX-201I

Har du brug for hjælp?

Hvis du har brug for hjælp til Elro SX-201I stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Dørklokke Elro Manualer

29 September 2024

13 September 2024

9 September 2024

28 August 2024

27 August 2024

Elro DB3000PL-P1C2B Manual

6 August 2024

Elro SX14EU Manual

2 August 2024

Elro DB3000PL-P1C2W Manual

1 August 2024

Elro SX41I Manual

1 August 2024

Elro DB3000-P1C1B Manual

29 Juli 2024

Dørklokke Manualer

Nyeste Dørklokke Manualer

EQ-3 HM-OU-CFM-TW Manual

16 December 2024

Cata EXTENDER 600 Manual

16 December 2024

Cata EXTENDER 700 Manual

16 December 2024

Cata CORONA 90 BK Manual

16 December 2024

Vimar ELVOX 40962 Manual

15 December 2024

Vimar ELVOX R975 Manual

15 December 2024

Vimar ELVOX 2501 Manual

15 December 2024

Emos P5733S Manual

12 December 2024

Emos P5729 Manual

12 December 2024

Emos P5728T Manual

12 December 2024