Ferguson FS2SD Manual

Ferguson Røgalarm FS2SD

Læs gratis den danske manual til Ferguson FS2SD (2 sider) i kategorien Røgalarm. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om Ferguson FS2SD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

5 6

7 8 9

Smoke Detector

User Manul

*Please read the user manual carefully before operation.

FS2SD

Product introduction

This product is a photoelectric smoke Detector. It is

a warning device, cannot sense gas, heat, or flame,

cannot prevent or put out fire. It is capable of

real-time detecting the presence of smoke,

detection of visible particles (smoldering fire) faster

than ionization smoke alarms. Red LED flashes

rapidly and detectors sound alarm once detecting

smoke fire danger, can alert you and your family

timely. Smoke alarms should be installed in all

rooms, living room, storage areas, basements and

attics unit where fire may happen.

Specyfication

Sensor Bracket

Tips

1.This device is designed specifically for home use, may not to

able to provide sufficient fire alert for public areas.

2.Please avoid installation in bathrooms and other very humid

places, dusty or greasy areas, or very airy place with air

conditioning, ceiling fans, etc.

3.Please keep device clean, and do not let dust to accumulate. It

is recommended to clean every 6 months with a household

cleaner and a soft brush.

4.The effective lifespan is 10 years. Replacement every 10 years,

regardless of breakdown or not.

5.Please pay attention if it alarms. Besides proper use of alarm,

we should also strengthen the consciousness of fire safety.

Test/Hush Button

and LED indicator

●Ceiling mounting

●Sloping ceiling mounting

Recommended and Avoided

Instalation Position

Sloping Ceiling Mounting

Position

Instalation Renderings

Area that air does not flow

Ceiling Centre

The preferred location to install smoke alarm is in the centre of the ceiling

because Smoke, heat and combustion products rise to the ceiling and

will lateral spread. Keep at least 30 cm distance from lights or

decorations, and at least 15 cm away from walls and corner. If hall is

more than 12 meters wide, please install at 2 sides of the hall.

If ceiling is sloping, please install the smoke alarm at horizontal distance

90cm away from the ceiling top.

Anticlockwise rotating the bracket out from the installation

base, then remove the battery insulating strip to make

device on power.

Remove the double-sided adhesive membrane on the

mounting bracket, and rotating the smoke alarm into

the bracket.

1. Operating voltage: DC3V(CR123A Lithium Battery)

2. Static current: ≤ 10µ A

3. Alarm current: ≤ 60mA

4. Sound level: 85dB/3m

5. Working Temperature: -10 ~+50

°C

6. Working humidity: ≤ 95%RH

7. Dimension: 60*60*49.2mm

Select the Smart Hub from the list of devices to which you want to

add a new device (sensor) or device with factory settings restored.

1.Click add devices on APP, entering networking mode.

Adding device

When the LED in the control

panel blinks blue, we confirm

and go to pairing devices.

2. According to the tips on APP, keep pressing networking

button, green LED flashes quickly, tips appear on APP,

green LED keep on for 3 seconds, network success.

Delete device

In the application, click and hold the selected device, the "delete

device" command will be displayed. After removed it, disconnect

the network connection device by pressing and holding the pairing

button. 6-fold LED blink in green means disconnection of the

sensor network from the HUB.

10 11 12

Status

Please refer to the following situation, if the Alarm can not work normally:

1. Battery reaches service life (status refer to Form 1). Please replace

battery.

2. Fault affected by dirt with dust or oil, etc. (status refer to Form 1). Please

clean the alarm correctly.

3. Whether the alarm is properly rotated into the mounting bracke

Mute mode and Test

Mute function

Please make sure that there is no real danger of fire when using

mute function. Under known and non-fire alarm condition,

please do not block or by any other form to prohibit alarming.

Press the Test/Mute button to lower sensitivity and relieve alarm.

Press and hold the test panel Test/Mute button for 3 seconds, as

above picture shows, until alarm status (see status table).

Testing is recommended to be done at least once a week. Do not

use flame for testing. Once the alarm is sure to please pay

attention.

Battery Replacement

CR123A

*Please replace battery correctly, following the battery positive

and negative electrode. Attention to environmental protection and

dispose used battery properly.

13 14 15

16 17 18

Notice

1. The malfunction auto check function of this smoke alarm

only provides infrared photoelectric sensor malfunction check

and low battery power check. The sensor sensitivity should be

tested periodically as required.

2. To ensure the sensitivity to smoke, clean the smoke alarm

surface with soft brush or cleaner every 6 months. Do not use

solvent, liquid or detergent to clean the smoke alarm.

3. For malfunction problems, please contact with vendor on

time. Do not dismantle and try to repair alarms by yourself.

4. If smoke alarms are not used for a long time, dismount

them, remove batteries, put them in packing box and store in

cool place.

5. Photoelectric smoke alarms could reduce disaster

happening. But they can not guarantee a hundred percent

safety. For your safety concern, please use this smoke alarm

correctly and know the fire safety tips. In daily life, pay

attention to build up safety consciousness and take

preventive measures.

Fire safety tips

Follow fire safety rules and prevent hazardous situations:

1. Store combustible liquids such as gasoline in proper containers.

2. Never smoke in bed. After smoking a cigarette, put it out and place in a

correct container.

3. Check if power sockets, plugs or switches are broke. If cables are frayed

or cracked replace them.

4. Using power electric appliances such as heaters or heating equipments, do

not make the circuit overload and check periodically if these appliances work

properly.

5. Keep portable heaters and open flames, like candles, away from flammable

materials.

6. Keep matches or lighters away from children.

7. Keep at least one working fire extinguisher on every floor and an additional

one in the kitchen. Have fire escape ladders or other reliable means of escape

from an upper floor in case stairs are blocked.

8. Make sure all the family members know what to do after hearing an alarm

signal.

9. Install smoke alarms correctly according to manual. Keep alarms clean and

do not let dust accumulate and test them monthly. Replace them immediately

if they are not working properly.

* this device requires Ferguson Smart Hub unit to work, not included.

Normal

Testing

Alarm

Mute mode

Low power

Fault

Red LED flashes every 53 seconds

Red LED flashes quicly

Red LED flashes every 10 seconds

Red LED flashes every 40 seconds

Rapid beeps

Beep every 40 seconds

Sta tus Light Ala rm Sound

Safety

1. Ferguson Sp. z o.o. is not responsible for damages caused by

improper use of the Ferguson Smart Home system.

2. Batteries attached to the device are not an integral part and not

a subject to complaint. The manufacturer is not responsible for

their proper operation.

3. Declared wireless ZigBee network’s range is based on

laboratory tests and applies to open space, keep in mind that the

materials used in the construction of houses and flats, wall

thickness and conditions of electromagnetic fields can cause a

significant reduction in network coverage.

Your product contains batteries covered by the

European Directive 2006/66/EC, which cannot

be disposed with normal household waste.

Please inform yourself about the local rules on

separate collection of batteries because correct

disposal helps to prevent negative

consequences for the environmental and human

health.

More info at

ferguson-digital.eu

and

wiki.ferguson.pl/en

Thanks!

Download app: Ferguson Smart

Produkt Specifikationer

Mærke:	Ferguson
Kategori:	Røgalarm
Model:	FS2SD

Har du brug for hjælp?

Hvis du har brug for hjælp til Ferguson FS2SD stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Røgalarm Ferguson Manualer

Ferguson FS2SD-GSM Manual

1 Juli 2024

Ferguson FS2SD Manual

1 Juli 2024

Røgalarm Manualer

Nyeste Røgalarm Manualer

First Alert SA710 Manual

9 Juli 2025

X-Sense XP04 Manual

9 Juli 2025

X-Sense XP0A-iR Manual

9 Juli 2025

X-Sense XS0B-MR31 Manual

9 Juli 2025

First Alert SMCO200 Manual

8 Juli 2025

GLORIA R-1 Manual

4 Juli 2025

CodeRED CRL-100 Manual

29 Juni 2025

CodeRED CRG-100 Manual

29 Juni 2025

GLORIA RC-10 Manual

25 Juni 2025

X-Sense SD2J0AX Manual

20 Juni 2025