Festo DADP-SP-G9-16-R Manual

Festo Ikke kategoriseret DADP-SP-G9-16-R

Læs nedenfor 📖 manual på dansk for Festo DADP-SP-G9-16-R (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
DADP-SP-G9-...-R
Sub-base kit
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Assembly instructions
8195137
2023-07a
[8195139]
8195137
Translation of the original instructions
© 2023 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
èwww.festo.com/sp.
Document Product Contents
Operating instruction Mini slide DGSS
Operating instruction Shock absorber DYEF, DYSS
Tab. 1: Applicable documents
2 Safety
2.1 Safety instructions
Only mount the product on components that are in a condition to be safely
operated.
2.2 Intended use
The sub-base kit in combination with two shock absorbers on the mini slide DGSS
cushions its extended and retracted end position. The sub-base contains the axial
air connections for the mini slide.
3 Additional information
Contact the regional Festo contact if you have technical problems
èwww.festo.com.
Accessories èwww.festo.com/catalogue.
4 Product Range Overview
4.1 Scope of delivery
1
2
3567 4
Fig.1
1
Screw (2x)
2
Stop (1x)
3
Stop element (1x)
4
Screw (2x)
5
O-ring (2x)
6
Connecting plate (1x)
7
Screw (4x)
4.2 Not in scope of delivery
8
9
Fig.2
8
Mini slide (1x)
DGSS
9
Shock absorber (2x)
DYEF-G8/DYSS-G8
5 Product design
Z
Z
Y
Fig. 3: Product design
Y
Axial air connections
Z
Thread for shock absorber
6 Assembly
1
A
B
2
Fig. 4: Pushing in stop
1. Extend the slide[A] manually.
2. Slide the stop into the slot[B].2
3. Insert the screws into the holes of the stop .1 2
4. Slide the stop to the end of the slot[B].2
A
C
1
Fig. 5: Mounting stop
1. Position the slide[A] so hole[C] is aligned with a screw .1
2. Tighten the screw . Observe the tightening torque.1
DADP-SP-G9 -6 -10 -16 -20
Screw M2 x 6 M2.5 x 8 M2.5 x 8 M3 x 12
[Nm] 0.3 ±15% 0.5 ±15% 0.7 ±15% 0.9 ±15%
3. Repeat this process for the second screw .1
C
3
Fig. 6: Note the stop bar
When installing the stop element , note the position of the stop bar[C].3
3
D
A
Fig. 7: Aligning stop element
1. Retract the slide[A] manually.
2. Position the upper edge of the stop element at the level of the thread[D].3
3
A
C
Fig. 8: Attaching stop bar
1. Push the stop element upwards to the stop.3
ÄThe stop bar[C] is in contact with the slide[A].
2. Hold this position.


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: DADP-SP-G9-16-R

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DADP-SP-G9-16-R stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Festo Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Emos

Emos DCPV02 Manual

13 Marts 2025
Hitachi

Hitachi RB367EY2 Manual

13 Marts 2025
Hitachi

Hitachi F-420EY2R Manual

13 Marts 2025
Hitachi

Hitachi R-V650EY2 Manual

13 Marts 2025
Hitachi

Hitachi R-V590EY2 Manual

13 Marts 2025
Hitachi

Hitachi R-B590EY2 Manual

13 Marts 2025
Philips

Philips AWP2662 Manual

13 Marts 2025
Rocstor

Rocstor KS20T Manual

13 Marts 2025
IFM

IFM IG6084 Manual

13 Marts 2025