Festo DAMH-L8-32-PL-1 Manual

Festo Ikke kategoriseret DAMH-L8-32-PL-1

Læs nedenfor 📖 manual på dansk for Festo DAMH-L8-32-PL-1 (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
Assembly instructions (Original instructions)
8070340
2017-07
[8070342]
†‡
Profile mounting
DAMH-L8-...-PL-1
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
1. Further applicable documents
All available documents for the product www.festo.com/pk
Operating instructions of the linear actuator 7
2. Safety
Switch off power supply and compressed air before mounting work.
Observe further applicable documents.
Comply with tightening torques ( Table).
3. Intended use
Fastening of two linear actuators 7 to a mounting surface.
4. Scope of delivery
18446d_1
1 Profile mounting
2 Sleeve
3 Screw
4 Screw
5 Knurled nut
6 Nut
(2x)
(2x)
(1x)
(1x)
(1x)
(1x)
5. Not in scope of delivery
18446d_2
7 Linear actuator
DLGF
8 Screw
(2x)
(4x)
6. Mounting
Determine the mounting points ( Further applicable documents).
18446d_3
Position actuators 7
flush with each other.
Place a knurled nut 5
into the drill hole (A) of
a determined fastening
point.
Lightly clamp the
actuators 7 into place
with the screw 4 and
knurled nut 5.
Place the sleeves 2
into the drill holes of the
profile mountings 1.
Push the screw 3 through
the sleeves 2, profile
mountings 1 and drill
holes (B) as shown.
18446d_4
Clamp the profile
mountings 1 to the
actuator 7 using the
hex nut 6.
Align the profile
mounting 1 parallel
to the actuators 7.
Tighten the hex nut 6.
Tighten the screw 4.
Repeat the mounting steps
for all mounting points.
18446d_5
Attach the profile
mountings 1 to the
mounting surface using
2 screws 8.
7. Screw sizes and tightening torques MA1)
Information
Select screws 8 suitable for the installation situation.
DAMH-L8-...-PL-1 20 25 32 40
3 Screw M4x60 M5x70 M6x90 M6x110
[Nm] 2.2 5.0 8.5 9.0
4 Screw M4x35 M5x45 M6x55 M6x70
[Nm] 2.2 5.0 8.5 9.0
6 Nut M4 M5 M6 M6
[Nm] 2.2 5.0 8.5 9.0
8 Screw M4 M5 M6 M6
1) Tolerances for tightening torques MA without indication of tolerance
MA . 3 Nm: ± 10 %
MA , 3 Nm: ± 20 %
7
7
7
8
6
4
8
1
2
3
5
7
4
2
3
1
2
1
5
A
B
B
6
1
1
4


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: DAMH-L8-32-PL-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DAMH-L8-32-PL-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Festo Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Emos

Emos DCPV02 Manual

13 Marts 2025
Hitachi

Hitachi RB367EY2 Manual

13 Marts 2025
Hitachi

Hitachi F-420EY2R Manual

13 Marts 2025
Hitachi

Hitachi R-V650EY2 Manual

13 Marts 2025
Hitachi

Hitachi R-V590EY2 Manual

13 Marts 2025
Hitachi

Hitachi R-B590EY2 Manual

13 Marts 2025
Philips

Philips AWP2662 Manual

13 Marts 2025
Rocstor

Rocstor KS20T Manual

13 Marts 2025
IFM

IFM IG6084 Manual

13 Marts 2025