Festo DARD-L8-20-S Manual

Festo Ikke kategoriseret DARD-L8-20-S

Læs nedenfor 📖 manual på dansk for Festo DARD-L8-20-S (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Translation of the original instructions
LOCTITE 243® is a registered trademark of its respective trademark holder in cer
tain countries.
1 Further applicable documents
All available documents for the product www.festo.com/pk.è
Observe further applicable documents:
Operating instructions of the linear drive5
2 Safety
2.1 Safety instructions
Before working on the product, switch off the power supply and secure it
against being switched on again.
Observe tightening torques. Unless otherwise specified, the tolerance
is±10%. Tightening torques 5 Technical data.è
Observe the safety data sheet for the adhesive from the original manufac
turer.
2.2 Intended use
Compensating element between the slide(A) of the linear drive and the pay5
load to be moved.
3 Product range overview
3.1 Scope of delivery
1Moment compensator (1x)
2Adhesive LOCTITE 243 (1x)
3Threaded pin (1x)
4Screw (3x)
Fig. 1
3.2 Not in scope of delivery
5Linear drive DLGFG (1x)
Fig. 2
4 Mounting
Positioning the moment compensator
Fig. 3
Place the moment compensator opposite the sensor slot(X) flush with the1
slide(A).
ÄThe sensor slot(X) is freely accessible.
Attaching the moment compensator
Fig. 4
Use the screws to attach the moment compensator to the slide(A). Do4 1
not tighten screws .4
Mounting the moment compensator
Fig. 5
1. Apply adhesive to the threaded pin .2 3
2. Screw the threaded pin into the moment compensator .3 1
3. Tighten the threaded pin .3
4. Tighten the screws .4
4.1 Mounting the payload
Hole for spring pin(B)
Fig. 6
Hole for spring pin(B) provided for centring the payload.
Recommended hole for spring pin(B): 5.2Æ+0.1mm
Mounting the payload on DARD-L8-20/25-S
Fig. 7
Mount payload with recommended screws using hole(C) or(D) on the
moment compensator .1
Hole(C) Hole(D)
Hole thread M5 M5
Recommended screws 2xM58.8 2xM48.8 ISO4762ß
Recommended tightening torques [Nm] 4.5 2.6
Tab. 1
When mounting the payload using hole(D), the threaded holeM5(C) serves as a
through hole for the screwM4.
8084730
Moment compensator
DARD-L8
8084730
201802a
[8084732]
Instructions| Assembly
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 3470
www.festo.com


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: DARD-L8-20-S

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo DARD-L8-20-S stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Festo Manualer

Festo

Festo SAMH-F12-MK Manual

17 November 2024
Festo

Festo SFAB Manual

17 November 2024
Festo

Festo SASC-P4-A-M8-S Manual

17 November 2024
Festo

Festo SFAH Manual

17 November 2024
Festo

Festo DRRD-12 Manual

17 November 2024
Festo

Festo SDE3 Manual

17 November 2024
Festo

Festo SFTE Manual

17 November 2024
Festo

Festo CRVZS-5 Manual

17 November 2024
Festo

Festo DGC-8 Manual

17 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024