Festo VMPA14-HS Manual


Læs nedenfor 📖 manual på dansk for Festo VMPA14-HS (1 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
VMPA...-HS
Vertical pressure shut-off plate
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8150088
2021-08a
[8150090]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
2 Safety
2.1 Safety instructions
Only use the product in its original condition without unauthorised modifica-
tions.
Only use the product if it is in perfect technical condition.
Before working on the product, switch off the compressed air supply and lock it
to prevent it from being switched on again.
2.2 Intended use
The vertical pressure shut-off plate enables replacement of a valve under oper-
ating pressure.
2.3 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can
evaluate the work and detect dangers. The qualified personnel have knowledge
and experience in pneumatics.
3 Additional information
Contact the regional Festo contact if you have technical problems
è www.festo.com.
4 Product Range Overview
4.1 Scope of delivery
1
2
3
4
Fig.1
1
Vertical pressure shut-off plate (1x)
VMPA...-HS
2
Washer (2x)
3
Distance piece (2x)
4
Fibre optic cable extension (1x)
4.2 Not in scope of delivery
5
Fig.2
5
Solenoid valve
VMPA...-M1H-…-PI
5 Assembly
5.1 Preparation
4
6
Fig.3
Push the fibre optic cable extension onto the electronics module .4 6
5.2 Assembly
1
2
3
7
8
Fig.4
1. Check that the conical ring seal is positioned correctly.7
ÄThe tapered side is at the bottom
2. Place the vertical pressure shut-off plate on the electronics module .1 8
3. Place the washers in the lateral slots with the rounding outwards.2
4. Tighten the distance pieces . Observe the tightening torque.3
Vertical pressure shut-
off plate
Spanner size of the dis-
tance pieces
Tightening torque
VMPA1-HS 2 0.4 Nm ± 10 %ß
VMPA14-HS 2 0.5 Nm ± 20 %ß
1
5
910
Fig.5
1. Check that the conical ring seal is positioned correctly on the solenoid9
valve .5
ÄThe tapered side is at the bottom
2. Place the solenoid valve on the vertical pressure shut-off plate .5 1
3. Tighten the screws . Observe the tightening torque.aJ
Solenoid valve Screw Tightening torque
VMPA1-M1H-...U-PI M2x40 0.25 Nm ± 10 %
VMPA1-M1H-...-PI M2x43 0.25 Nm ± 10 %
VMPA14-M1H-...-PI M2.5x45 0.65 Nm ± 10 %


Produkt Specifikationer

Mærke: Festo
Kategori: Ikke kategoriseret
Model: VMPA14-HS

Har du brug for hjælp?

Hvis du har brug for hjælp til Festo VMPA14-HS stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Festo Manualer

Festo

Festo SAMH-F12-MK Manual

17 November 2024
Festo

Festo SFAB Manual

17 November 2024
Festo

Festo SASC-P4-A-M8-S Manual

17 November 2024
Festo

Festo SFAH Manual

17 November 2024
Festo

Festo DRRD-12 Manual

17 November 2024
Festo

Festo SDE3 Manual

17 November 2024
Festo

Festo SFTE Manual

17 November 2024
Festo

Festo CRVZS-5 Manual

17 November 2024
Festo

Festo DGC-8 Manual

17 November 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024