Fisher & Paykel E402BLXFD4 Manual

Fisher & Paykel Køleskab E402BLXFD4

Læs nedenfor 📖 manual på dansk for Fisher & Paykel E402BLXFD4 (56 sider) i kategorien Køleskab. Denne guide var nyttig for 43 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/56

INSTALLATION GUIDE / USER GUIDE

NZ AU GB IE EU AE HK SG

E372B, E402B, E442B, E522B, RF372B, RF402B, RF442B,

RF522B, RF522W, RF522A, RF610A & RF540A models

ACTIVESMART™ REFRIGERATOR

ICE & WATER, AUTOMATIC ICE

AND NON-ICE & WATER MODELS

CONTENTS

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this user guide may not

be available in all markets and are subject

to change at any time. For current details

about model and specification availability

in your country, please go to our website

fisherpaykel.com or contact your local

Fisher & Paykel dealer.

Note: the word ‘refrigerator’, throughout this

user guide, refers to the combination

of refrigerator/freezer products.

Registration

provide you with the best service possible.

To register your product visit our website:

fisherpaykel.com

Introduction 2

Safety and warnings 3

Installation instructions 12

Moving or storing your appliance 25

ActiveSmart™ operating instructions 26

All about the external display (Ice & Water models only) 30

Using your water dispenser (Ice & Water models only) 31

Water filter (Ice & Water and Automatic Ice models only) 32

Using your ice maker (Ice & Water and Automatic Ice models only) 33

ActiveSmart™ special features 34

Cleaning and caring for your refrigerator 37

Foodcare 41

Moving or storing your appliance 42

ActiveSmart™ user warnings and sounds 43

Troubleshooting 44

Manufacturer’s Service & Warranty 49

European Directive 2012/19/EU on

Waste Electrical and Electronic Equipment (WEEE) 50

INTRODUCTION

Thank you for buying a Fisher & Paykel ActiveSmart™ refrigerator.

At Fisher & Paykel we are very proud of this refrigerator. This refrigerator combines size and

storage space with the latest features and functions.

Thousands of hours of food care research and refrigeration experience has been

programmed into your refrigerator to give you the best possible performance.

We hope you enjoy your new refrigerator.

Note: Automatic Ice and non-Ice & Water models do not have an external water dispenser.

Refrigerator French door

and freezer drawer

Refrigerator door

and freezer door

Refrigerator door

and freezer drawer

ActiveSmart™ refrigerators have two handle

options, shown below.

Pocket handlesDesigner handles

SAFETY AND WARNINGS

! WARNING!

Electric Shock Hazard

Read and follow the safety and warnings

outlined in this User guide before operating

this appliance.

Failure to do so can result in death, electric

shock, fire or injury to persons.

WARNING: Risk of fire/flammable material

This refrigerator contains flammable

refrigerant isobutane (R600a).

Use this appliance only for the intended purpose as

described in the user guide.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

When using this appliance always exercise basic safety

precautions including the following:

• This appliance can be used by children aged 8years

and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision

or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

• Children aged 3 to 8 years may load and unload this

appliance under supervision.

• Children should be supervised to ensure that they do

not play with the appliance.

• Cleaning and user maintenance shall not be made by

children without supervision.

SAFETY AND WARNINGS

• The manufacturer’s installation instructions for

product and cabinetry ventilation must be followed

when installing the appliance.

• To avoid hazard due to instability of the

appliance, it must be fixed in accordance with

installation instructions.

• WARNING: Keep ventilation openings, in the

appliance enclosure or the built-in structure, clear

of obstruction.

• WARNING: Do not use mechanical devices or other

means to accelerate the defrosting process, other

than those recommended by the manufacturer.

• WARNING: Do not damage the refrigerant circuit.

• In case of damage to the refrigerant circuit, ventilate

the area by opening all windows. Do not operate

electrical equipment or any other equipment that

may produce arcs, sparks or flames in the area.

Contact your Fisher & Paykel trained and supported

service technician immediately to arrange for the

appliance to be repaired.

• It is hazardous for anyone other than a Fisher &

Paykel trained and supported service technician to

service thisappliance.

• In Queensland the authorised service person

must hold a gas work licence or authorisation for

hydrocarbon refrigerants to carry our service or

repairs which involve removal of covers.

• Opening the door for long periods can cause a

significant increase of the temperature in the

compartments of the appliance.

• WARNING: Connect to safe drinking water only.

SAFETY AND WARNINGS

Electrical WARNING

• This appliance must be installed in accordance with

the installation instructions before use.

• To allow disconnection of the appliance from the

supply after installation, incorporate a switch in the

fixed wiring in accordance with the wiring rules.

• Never unplug your refrigerator by pulling on the

power cord. Always grip the plug firmly and pull

straight out from the outlet.

• Do not plug in any other appliance at the same

power point as your refrigerator or use extension

cords or double adapters.

• Repair or replace immediately all electric service

cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks or

abrasion along its length or at either the plug or

appliance end.

• If the power supply cord is damaged, it must only

be replaced by your Fisher & Paykel trained and

supported service technician because special

purpose tools are required.

• When moving your appliance away from the wall, be

careful not to roll over or damage the power cord.

• Do not use electrical appliances inside the food

storage compartments of the appliance, unless they

are of the type recommended by the manufacturer.

SAFETY AND WARNINGS

• When positioning the appliance, ensure the power

cord is not trapped or damaged.

• Do not locate multiple portable socket-outlets or

portable power supplies at the rear of the appliance.

IMPORTANT!

Your refrigerator is designed to operate for many years

without the need for service checks. However, if your

refrigerator is malfunctioning, have it attended to by

your Fisher & Paykel trained and supported service

technician as soon as possible. All electrical repairs

must be carried out by an adequately trained service

technician or qualified electrician.

Cleaning

• Many commercially available cleaning products

contain solvents that may attack the plastic

components of your refrigerator and cause them

tocrack.

• Avoid using anti-bacterial cleaning products on

either the interior or exterior of the cabinet as they

may cause rusting of metal components and cracking

of plastic components.

• Please refer to the ‘Cleaning and caring for

your refrigerator’ section of this user guide for

further information.

Disposal

• Extreme care must be taken when disposing of your

old appliance to avoid hazards:

– The flammable refrigerant gas must be

safely removed.

SAFETY AND WARNINGS

– The thermal insulation foam in this appliance

contains flammable insulation blowing gases, any

exposed foam may be highly flammable and must

be carefully treated during disposal.

– The doors and panels should be removed and

the shelves left in place so that children may not

easily climb inside.

• Your Fisher & Paykel trained and supported

service technician will be able to give advice on

environmentally friendly methods of disposing of

your old refrigerator or freezer.

Food Safety

• Regularly clean accessible draining systems and

surfaces that come in contact with food.

• Store raw meat and fish in suitable containers in the

refrigerator, so that it is not in contact with or drip

onto other food.

• If the appliance will be left empty for long periods,

switch off, defrost, clean, dry, and leave the

door open to prevent mould developing within

the appliance.

Storing food and drinks

• Do not store explosive substances such as aerosol

cans with a flammable propellant in this appliance.

• Never store volatile or flammable materials in your

refrigerator as they may explode.

• Never freeze liquids in glass containers. Liquid

expands during freezing, which may cause the

container to explode.

SAFETY AND WARNINGS

• Never freeze carbonated drinks. They may explode.

• Do not consume food if it is too cold. Food removed

from the freezer compartment may be cold enough

to cause damage when brought into contact with

bare skin, eg frozen ice cubes.

Power failure — food safety

• Do not refreeze frozen foods that have thawed

completely. The food may be dangerous to eat.

Follow the recommendations below if you discover

food in your freezer has thawed:

– Ice crystals still visible — food may be refrozen

but should be stored for a shorter period

than recommended.

– Thawed but refrigerator cold — refreezing

generally not recommended. Fruits and some

cooked food can be refrozen but use as soon as

possible. Meat, fish, poultry — use immediately or

cook then refreeze. Vegetables — discard as they

usually go limp and soggy.

– Thawed and warmer than 5°C — discard all food.

SAFETY AND WARNINGS

Water filter

IMPORTANT!

• The water connection to your Ice & water refrigerator

must be installed by a qualified plumber or Fisher &

Paykel trained and supported service technician and

comply with all state and local laws.

• Installation and use MUST comply with all state

and local plumbing codes. Checkwith your local

public works department for plumbing codes. You

must follow their guidelines as you install the water

filtration system.

• To avoid serious illness or death, only connect your

water filter to safe drinking water.

• The water filter cartridge needs to be changed when

the replacement indicator icon illuminates. This will

happen every 6 months.

• If the water filtration system has been allowed to

freeze, replace filter cartridge. Failure to replace

the disposable filter at recommended intervals may

lead to reduced filter performance and failure of the

filter, causing property damage from water leakage

or flooding.

• In cases of excessively reduced filter life — we

recommend that you consult a local plumber or

your water supplier for advice on suitable filtration

requirements for the water supplied to your home.

• Filter replacement is the consumer’s responsibility

and will not be covered by the warranty except

in the case of faulty parts or materials within the

filter cartridge.

SAFETY AND WARNINGS

• If the water has not created ice for some time or ice

has an unpleasant taste or odour dispose of ice and

refer to ‘Before you start using the Ice & Water or

Automatic Ice function’ for flushing instructions. If

unpleasant taste or odour persists, you may wish to

fit a new filter cartridge.

• Use new tubing supplied with the refrigerator.

DO NOT reuse old tubing from old water

and ice connections.

• Your water filtration system can withstand up to

120psi (827kPa) of water pressure. Ensure the

supplied pressure reducing valve is installed before

installing the water filtration system. DO NOT install

if water pressure exceeds 120psi (827kPa).

• To reduce the risk associated with property damage

due to water leakage or flooding:

• DO NOT install systems in areas where ambient

temperatures may go above 100°F (38°C) or drop

below 33°F (0.6°C).

• DO NOT install on hot water supply lines. The

maximum operating water temperature of this filter

system is 100°F (38°C).

• DO NOT install where water hammer conditions may

occur. If water hammer conditions exist, you must

install a water hammer arrester.

• Clean the water tanks if they have not been used for

48 hours. Flush the water system connected to the

water supply if water has not been used for 5 days.

SAFETY AND WARNINGS

Ice making

IMPORTANT!

• Avoid contact with the moving parts of the ice maker

ejector mechanism, and do not place your fingers

on the automatic ice-making mechanism while the

appliance is inoperation.

• Do not use ice cubes that may have become

discoloured, usually with a green-blue colour. If such

discolouration is noted, discard the ice cubes and

contact your Fisher&Paykel trained and supported

service technician.

INSTALLATION INSTRUCTIONS

Please follow the installation steps below to ensure your appliance operates correctly.

1. Power

zThe appliance must be installed so the plug is accessible.

zTo ensure that the appliance is not accidentally switched off, connect your refrigerator

to its own power point. Do not plug in any other appliance at this power point or use

extension cords and double adaptors, as the combined weight of both power cords can

pull the double adaptor from a wall outlet socket.

zFor power requirements, refer to the information on the serial plate located at the front

bottom right-hand side of the refrigerator when the door is open.

zIt is essential that the appliance is properly grounded (earthed).

2. Location

zYour refrigerator should not be located in direct sunlight or next to any heat generating

appliance such as a cooktop, oven or dishwasher.

3. Ice & Water and Automatic Ice models

zYour Ice & Water and Automatic Ice refrigerator must be installed by an authorised

plumber or Fisher & Paykel trained and supported service technician as incorrect

plumbing can lead to water leaks.

zFisher & Paykel Appliances does not accept responsibility for damage (including water

damage) caused by faulty installation or plumbing.

INSTALLATION INSTRUCTIONS

4. Product and cabinetry dimensions

If integrating your refrigerator, please follow installation instructions provided with the

integration kits.

Freezer door models (E372B, RF372B, E402B, RF402B, E442B, RF442B, E522B, RF522B)

(Ice & Water, Automatic Ice and non-Ice & Water models)

Flush with refrigerator

chassis — full door rotation

Flush with refrigerator

door — full door rotation

Flush with refrigerator

door — 90° door rotation

B C

E372B

RF372B

E402B

RF402B

E442B

RF442B

E522B

RF522B

PRODUCT DIMENSIONS MM

A Overall height of product 1620 1720 1720 1720

B Overall width of product 1620 1720 1720 1720

C Overall depth of product

(excl. handle, includes evaporator) n/a 695 695 695

CABINETRY DIMENSIONS (incl. minimum clearances) MM

D Inside height of cavity 1645 1735 1735 1735

Flush with refrigerator chassis — full door rotation

E Inside width 675 675 720 830

F Inside depth 620 620 620 620

Flush with refrigerator door — full door rotation

G Inside width 790 790 835 945

H Inside depth flush to door n/a 695 695 695

Flush with refrigerator door — 90° door rotation

(for full drawer/shelf access, the doors need to be open past 90°)

I Inside width 745 745 790 900

J Inside depth flush to door n/a 695 695 695

MINIMUM CLEARANCES MM

K Side clearance 20 20 20 20

L Side clearance — hinge side flush with

door — full rotation 135 135 135 135

M Side clearance — hinge side flush with

door — 90° rotation 90 90 90 90

N Rear clearance (incl. evaporator tray) 30 30 30 30

O Vent — around top of cupboard (optional) 50 50 50 50

P Top clearance — above refrigerator cabinet 50 50 50 50

Q Door clearance — hinge side flush with

chassis — full rotation 520 520 555 645

R Door clearance — hinge side flush with

door — full rotation 405 405 440 530

INSTALLATION INSTRUCTIONS

4. Product and cabinetry dimensions

If integrating your refrigerator, please follow installation instructions provided with the

integration kits.

Freezer drawer models (RF522W, RF522A, RF610A/RF540A)

(Ice & Water, Automatic Ice and non-Ice & Water models)

Flush with refrigerator door — full door rotation

Flush with refrigerator door — 90° door rotation

Flush with refrigerator door — full door rotation

Flush with refrigerator door — 90° door rotation

RF522A, RF610A/RF540ARF522W

Flush with refrigerator chassis — full door rotation Flush with refrigerator chassis — full door rotation

INSTALLATION INSTRUCTIONS

A A

O O

P P

D D

N N

K L

L L

F F

H H

J J

RF522W RF522A

RF610A/

RF540A

PRODUCT DIMENSIONS MM

A Overall height of product 1720 1720 1800

B Overall width of product 790 790 900

C Overall depth of product

(excl. handle, incl. evaporator) 695 695 695

CABINETRY DIMENSIONS (incl. minimum air clearances) MM

D Inside height of cavity 1735 1735 1810

Flush with refrigerator chassis — full door rotation

E Inside width 830 830 940

F Inside depth 620 620 620

Flush with refrigerator door — full door rotation

G Inside width 945 1060 1170

H Inside depth flush to door 695 695 695

Flush with refrigerator door — 90° door rotation

(for full drawer/shelf access, the doors need to be open past 90°)

I Inside width 900 1015 1125

J Inside depth flush to door 695 695 695

MINIMUM CLEARANCES MM

K Side clearance 20 20 20

L Side clearance — hinge side flush with

door — full rotation 135 135 135

M Side clearance — hinge side flush with

door — 90° rotation 90 90 90

N Rear clearance (incl. evaporator tray) 30 30 30

O Vent — around top of cupboard (optional) 50 50 50

P Top clearance — above refrigerator cabinet 50 50 50

Q Door clearance — hinge side flush with

chassis — full rotation 645 325 365

R Door clearance — hinge side flush with

door — full rotation 530 210 250

INSTALLATION INSTRUCTIONS

5. Connecting water (Ice & Water and Automatic Ice models)

Cotents of filter kit

A 1 x tap connection

B 1 x short tubing

C 1 x locking key

D 1 x pressure limiting valve (PLV)

E 1 x water filter cartridge

F 1 x wall mounting bracket, filter head and tubing

G 2 x screws

IMPORTANT!

zA pressure limiting valve (PLV) must be fitted prior to the water filter. The PLV protects

your refrigerator from damage. If the PLV is not fitted to the connection line your

warranty will be void and the product may leak.

zThe water connection instructions below are intended only for the professional installer.

zThe new tubing supplied with the refrigerator is to be used, old tubing from old water

and ice connections should not be used.

zEnsure the inlet tubing is correctly connected to the PLV. Failure to do so may result in

serious injury.

zReplacement parts are available through Customer Care or online at fisherpaykel.com

(this service is available to selected markets only).

INSTALLATION PRECAUTIONS/WARNING

zDO NOT cut any length of tube shorter than 500mm.

zDO NOT install near electrical wires or water pipes that will be in the path of drilling

when selecting the location of filter system.

zDO NOT mount the water filter in such a position so that it will be struck by other

items, such as wastebaskets.

zDO NOT install the water filter or any water tubing in direct sunlight as prolonged

exposure to light can weaken plastic components.

zDO NOT install in a location that is susceptible to freezing temperatures as damage to

the housing could occur.

zDO NOT screw water filter mounting bracket to the refrigerator.

zDO NOT install the filter or any water tubing in high temperature areas eg in a

ceiling cavity.

zAVOID contamination of pipes during installation.

zDO NOT continuously dispense water for longer than 2minutes.

BA GC FD E

INSTALLATION INSTRUCTIONS

Installation instructions:

1 Ensure the refrigerator is NOT plugged into

a powersupply.

2 Locate a cold water supply/feed that is

suitable for a water connection.

3 Connect the tap connection fitting ( ) to A

the tap. Connect the short tubing ( ) to B

the outlet of the tap and secure with the

locking key ( ) (refer to Diagram 1)C

4 Connect the inlet of the PLV ( ) to the D

tubing connected to the tap (refer to

Diagram 2). Ensure the arrow on the PLV

is pointing away from the tap. The arrow

indicates the direction of waterflow.

5 Connect the inlet tube from the filter head

to the PLV (refer to Diagram 3). The inlet

tube can be identified by the downward

arrow on the filter head and a red

mark on the tube.

IMPORTANT!

Ensure the outlet tubing is correctly

connected to the refrigerator water valve.

Refer to Diagram 3.

6 Determine the mounting position for the

water filter noting the following:

zThe water filter MUST not be mounted

with the filter head position below the

base of the filter (refer to Diagram 4). We

recommend fitting the water filter in a

vertical orientation with the filter head at

the top. This will minimise water leakage

during replacement of the waterfilter.

zEnsure the water filter is in a convenient

location to access every 6months for

replacement. We recommend that this

location is beside the water filter supply tap

in a cupboard beside the refrigerator.

zA minimum clearance of 50mm from the

bottom of the water filter is required to

perform filter removal.

Diagram 1

Diagram 2

Diagram 3

0° – 90°

Diagram 4

Inlet

tube

water flow

from PLV

water flow to

refrigerator

INSTALLATION INSTRUCTIONS

7 Attach the wall mounting bracket with the

two screws provided, attach the bottom

screw first then the top screw (refer

to Diagram5).

8 Insert the filter water into the filter head.

Push the filter firmly into the filter head and

turn in a clockwise direction until it locks into

place (refer to Diagram 6).

9 To flush the water filter of any trapped air,

harmless carbon fines and check for leaks:

Aim the end of the filter outlet tubing into a

bucket, turn on the tap and run 8L of water

through. Once complete, turn the tap off.

Note: Further flushing is required before first

use of your ice or water functions, please refer

to ‘Before you start using the Ice & Water or

Automatic Ice function’ for details.

!0 Run the 6mm tubing to the back of the

refrigerator ensuring there is enough tubing to

pull the refrigerator out for service.

!1 Using the measurement guide shown in Diagram 7, mark out 16mm, on the end of the

tubing as shown in Diagram 8.

!2 Insert the outlet tubing to the water (solenoid) valve up to the marked line. The

outlet tube can be identified by the upward arrow on the filter head and a blue

mark on the tube.

!3 Pull gently on tubing to ensure it is locked in as shown in Diagram 10.

!4 Turn the tap on and check that all connections are dry and free of drips.

!5 Coil water line tubing behind the refrigerator. Pushyour refrigerator into place being

careful notto kink or squash the water line tube.

!6 Read pages 17 – 18 carefully and then turn refrigeratoron.

Diagram 7

Diagram 9 Diagram 10Diagram 8

Completed installation

INSTALLATION INSTRUCTIONS

Diagram 5

Diagram 6

IMPORTANT!

zAll connections must be checked for leaks.

zEnsure 6mm tubing is routed away from sharp objects, sharp

corners (beware of kinking the tube as this will stop water

flow), clear of the refrigerator rear compartment and not in a

location where it can be kinked or squashed.

zEnsure all push-fit connections are firmly pushed into place.

The tube should push in 16mm before reaching the stop.

zIf tubing is removed at any point, re-cut the end and

re-insert. Tubing must be fully inserted to avoid leaks.

zTo remove tube from connection points first turn off the

isolating faucet. Gently push the dispensing pad a few times

using a glass or container to remove the static line pressure.

Push in the collet firmly while pulling back on the tubing at

the same time, as shown in Diagram11.

847200 – Certified by: IAPMO R&T against NSF/ANSI Standards 43, 53, 401 and CSA

B4831.1 for the reduction of claims specified on the performance data sheet and at iapmort.

org. 847200 compounds certified under NSF/ANSI 401 have been deemed as incidental

contaminants/emerging compounds. Incidental contaminants are those compounds that

have been detected in drinking water supplies at trace levels. While occurring at only trace

levels, these compounds can affect the public acceptance of drinking quality water.”

847201 – Certified by: IAPMO R&T against NSF/ANSI Standards 43 and CSA B4831.1 for the

reduction of claims specified on the performance data sheet and at iapmort.org.

Rated capacity:

847200 – 102 gallons (386 litres)

847201 – 170 gallons (643.5 litres)

Diagram 11

INSTALLATION INSTRUCTIONS

Before you start using the Ice & Water or Automatic Ice function

zCheck your refrigerator is switched on.

zAllow at least 2hours for your refrigerator to cool before use.

zComplete all the flushing steps detailed in this installation/user guide to ensure

optimum performance of your water filter.

For Ice & Water models only:

1 Press the water dispenser pad to dispense 2L of water.

zThere may be carbon residue dispensed together

with water. This is not harmful, and normal during

flushing process.

2 Wait for 2 minutes before dispensing again.

3 Dispense another 2L of water. Your water dispenser is

now ready for use.

4 Water will continue to drip from the dispenser for a

few more days after installation to clear remaining

trapped air in the dispenser. Check the drip tray

regularly and empty when required.

For Ice & Water and Automatic Ice models:

1 Turn the ice maker on by pressing the button.

Thelight above the button will be illuminated

whenthe ice maker is on.

2 Press the , and together for 4seconds then

close the doors. The ice tray will empty the water into

the bin below. The ice tray will only empty after the

doors are closed.

3 Repeat step to remove dust in the ice tray collected 2

during manufacture and transport.

4 Empty the water, dry the bin and return it correctly

(refer to diagrams 1 and 2 for placement of ice bins

for your refrigerator).

5 Once your ice maker is turned on the first bin of ice

may be discoloured, this is not harmful and normal

during the flushing process. Discard the first full bin

ofice made. Your ice maker is now ready for use.

zFor Ice & Water models: the water filter will

reach optimum performance after two to three

full bins of ice.

zFor Ice only models: the water filter will reach

optimum performance after four to five full binsof ice. Ice storage bin and scoop

in correct position

Diagram 1

Diagram 2

Water dispenser

INSTALLATION INSTRUCTIONS

6. Installation (all models)

Your Fisher & Paykel ActiveSmart™ refrigerator is

fitted with front and rear rollers, designed for moving

the product in the forwards and backwards direction.

Avoid moving the product in a sideways direction

as this may damage the rollers or the floor

covering/surface.

A Your refrigerator will arrive with the front feet

wound up making moving the product into its

final location a simple task.

B Roll the refrigerator into its final position making

sure there is the correct air gap between the

product and surrounding cabinetry. See minimum

clearance in cabinetry dimensions table.

C Adjust the front feet down until the refrigerator

is leaning backward with the front approximately

10mm higher than the back. This will ensure a

good door closing action.

(Non French door models only)

D Aligning your refrigerator with cabinetry.

zAlign the sides of the refrigerator with the cabinetry

by adjusting the hinge side front foot.

zAdjust the handle side foot until it touches the floor

and takes a small amount of weight.

zOnce the refrigerator is in place and aligned with

cupboards/alcove gently push on the front top and

check if the product is rocking or stable.

7. Levelling of refrigerator doors

(French door models only)

zFor uneven surfaces, front feet can be used to

align the 2 doors.

zIf left hand door is too low, then unscrew the left hand

foot to lift up the cabinet until the two doors top

edges are aligned.

zIf right hand door is too low, then adjust the right

hand foot in the same way.

Even door alignment

Uneven door alignment

Raise the

front of the

refrigerator

Lower the

front of the

refrigerator

Refrigerator feet

INSTALLATION INSTRUCTIONS

8. What to do if your product is unstable

A Gently push the refrigerator back until the rear

rollers contact the floor.

zMeasure the gap under the front foot, which has

come off the floor.

zObtain some solid packing material (hardwood,

plastic,etc.) which fits firmly into the gap

under the foot.

Note: do not use metallic materials that may corrode,

stain and/or damage floor coverings.

B Wind both front feet up and roll the product

out ofposition.

zPlace the packing material in the location diagonally

opposite the front roller that lifts off the floor.

zMake sure the packing material stays in place when

the product is pushed back into position.

zIdeally, the packing material is large enough to

rest against the back wall so as to prevent it from

moving when the cabinet is pushed into position.

Wall behind refrigerator

For example: if this foot lifts off the floor when

pushing gently on the top front of the refrigerator

Packing material goes under rear roller

diagonally opposite front foot that lifts

Stabilising your refrigerator

C Roll the refrigerator back into position and adjust front feet as per step 6 C.

(Check alignment and door closing action are satisfactory).

zMake small adjustments to front feet where necessary.

zCheck that the product is stable (all 4 feet are on the floor).

If not, repeat 8 A and 8 B

This foot lifts off the floor

when top front is gently

pushed back

Example only

Unlevel floor

Unstable refrigerator

INSTALLATION INSTRUCTIONS

Before placing food in the fresh food or freezer compartments

zRemove all internal packaging. Ensure that all transit clips are removed from the

refrigerator. These are small rubber stoppers located at the back of the shelves.

zClean the inside of the appliance with a mix of warm water and a small amount of liquid

detergent, and a soft cloth to remove manufacturing and transportation dust.

zAllow the refrigerator and freezer to run empty for 2 – 3 hours to allow each

compartment to cool to the appropriate temperature.

zThe appliance may have an odour on its initial operation, but this will go when the

refrigerator and freezer have cooled sufficiently.

Energy efficiency

For the most energy efficient use of your appliance:

zEnsure your refrigerator has adequate ventilation.

zDo not cover your appliance with any material that will prevent air from flowing around

the cabinet sides.

zEnsure you vacuum around the appliance to remove dust and possible pet hair

accumulation. Also keep the appliance and its cabinetry free of dust by wiping down

with a dry, lint-free cloth (refer to section ‘Cleaning and caring for your refrigerator’,

‘Cabinet surround’).

zAllow good clearances in front of air ducts within the cabinet for maximum cold

air distribution.

zCool hot foods down before placing them in the appliance.

zDo not overfill the compartments.

zKeep door openings to a minimum.

zSelect a temperature setting that isn’t too cold.

zCheck your door seals for leaks.

INSTALLATION INSTRUCTIONS

MOVING OR STORING YOUR APPLIANCE

If your refrigerator is turned off for any reason, wait 10minutes before turning it back on.

This will allow the refrigeration system pressures to equalise before restarting.

Moving your refrigerator

zTurn off the appliance and unplug from the power point. Remove all food.

zTurn the adjustable feet to the right as far as they will turn.

zEase the refrigerator out of its position. Tuck the power cord away, tape the shelves in

place and tape the doors closed. If the cabinet needs to be placed at an angle or laid

down, carefully lay it on its side (the right hand side when viewed from the front).

zRelocate and install. If the appliance has been left on its side for any length of time, leave

it standing upright as long as you can (a few hours) before turning on.

Storing your refrigerator

zWhen storing your cleaned appliance, leave the doors open. This allows air to circulate

and prevents the build up of bacteria and moulds.

zBefore using again, clean well using a mixture of warm water and a small amount of

liquid dishwashing detergent. Rinse with clean water and dry with a soft lint-free cloth.

Holiday time

We recommend you leave your refrigerator operating while you are on holiday.

ACTIVESMART™ OPERATING INSTRUCTIONS

Models:

635mm wide E372B, E402B, RF372B, RF402B

680mm wide E442B, RF442B

790mm wide E522B, RF522A, RF522W, RF522B

900mm wide RF610A/RF540A

The control panel enables you to view and modify features and options on

your refrigerator.

Temperature control (all models)

zThe powerful cooling system will automatically cool both refrigerator and freezer

compartments to their recommended ideal temperatures — 3°C refrigerator and -18°C

freezer. This will take between 2 – 3hours.

zThe two compartment temperatures are accurately and independently controlled

and do not change with the temperature or humidity of the surroundings; whether

summer or winter.

zIf you wish to alter the temperature of either the fresh food compartment or freezer

compartment, this can be easily done by using the internal control panel located at the

front right of the refrigerator compartment.

Internal control panel to adjust temperatures

Control panel variants for ActiveSmart™ refrigerators.

Extra features available on selected models.

ACTIVESMART™ OPERATING INSTRUCTIONS

Fresh food compartment (all models)

zThe fresh food compartment light will automatically be illuminated. The temperature for

this compartment will show as a series of lights.

zThe temperature may be altered by pressing the or buttons. One press on either of

these buttons will reduce or increase the number of lights by one which indicates a small

change in temperature.

zFewer lights illuminated means a cooler temperature for the compartment selected.

Freezer food compartment (all models)

zTo adjust the freezer temperature press the button once so the freezer compartment

light is illuminated.

zThe freezer temperature can be altered by pressing the or buttons.

zOne press on either of these buttons will reduce or increase the number of lights

illuminated which indicates a small change in temperature.

zFewer lights illuminated means a cooler temperature for the compartment selected.

Note: successively pressing the button will automatically scroll between

the compartments.

zWhen the door is re-opened the control panel will return automatically to the fresh food

compartment setting.

Alarm Mute (all models)

For times when you require the door to be open longer than normal eg when cleaning

the interior of your refrigerator press the ‘Alarm Mute’ button to silence the door alarm

for 20minutes.

zTo activate, press the button once. The ‘Alarm Mute’ light will be illuminated when the

function is activated.

z‘Alarm Mute’ will deactivate after 20minutes and the door alarms will return to normal.

zTo deactivate ‘Alarm Mute’ manually, press the button again. When ‘Alarm Mute’ is

deactivated the light is off.

Note: when the fresh food or freezer compartment door is left open for long periods of

time food quality and / or safety may be compromised.

Door alarms (all models)

zIf the fresh food compartment door is left open the alarm will beep after 90seconds and

if the freezer door is left open the alarm will beep after 60seconds.

zWhile either door remains open, subsequent beeps will sound every

30seconds for 5minutes.

zA continuous alarm will sound if either of the doors have been left open for 5minutes or

longer and the interior compartment light(s) will turn off. The alarm will stop only when

the door(s) is closed.

Note: if ‘Alarm Mute’ has been activated the door alarms will be silenced for 20minutes.

After 5minutes of the doors being left open the compartment light will turn off however

the normal door alarms will be suspended. The ‘Alarm Mute’ light will be illuminated to

indicate that the appliance is in this mode.

ACTIVESMART™ OPERATING INSTRUCTIONS

Key Mute (all models)

‘Key Mute’ allows you to silence all button presses.

zTo activate ‘Key Mute’ and silence buttons, press and hold the button for 4seconds.

zThe icon on the internal control panel will be illuminated.

zThe keys will be silenced when ‘Key Mute’ is activated.

zDoor alarms and ‘Bottle Chill’ alarm will still operate.

z‘Key Mute’ will not automatically deactivate. To manually deactivate, press and hold the

button for 4seconds.

zThe icon will no longer be illuminated.

Key Lock (all models)

‘Key Lock’ allows you to disable the buttons on the internal control panel. This is useful

when cleaning your refrigerator.

zTo activate ‘Key Lock’ press and hold the and buttons for 4seconds.

zThe icon on the internal control panel will be illuminated.

zPressing any of the buttons will cause a raspberry beep to tell you that they are disabled.

z‘Key Lock’ will not automatically deactivate. To manually deactivate, press and hold the

and buttons for 4 seconds.

zThe icon will no longer be illuminated.

Sabbath Mode activation (all models)

zTo activate ‘Sabbath Mode’, open the door(s) of the fresh food compartment and freezer

compartment and then press and hold the buttons on the internal control , and

panel for 4seconds.

zThe candle icon will illuminate when ‘Sabbath Mode’ has been activated.

When the product is in Sabbath Mode:

zThe icon on the internal control panel will be illuminated.

zAll lights on the internal control panel except for the candle icon will be off.

zThe fresh food or freezer compartment lights will not operate when the

door(s) is opened.

zThe door alarms will not operate.

zThe internal control panel will not function except to indicate ‘Sabbath Mode’ is active

as stated above.

zOpening the door(s) will not affect the compressor or fans.

zIf the power to the refrigerator is turned off whilst in this mode, the product will continue

in ‘Sabbath Mode’ when the power is restored.

z‘Sabbath Mode’ will automatically de-activate 80 hours after activation.

zTo de-activate earlier than 80 hours press and hold the buttons for , and

4seconds. The candle icon will no longer illuminate on the internal control panel (and

external display for Ice & Water models) and functionality of the internal control panel

will return to normal.

ACTIVESMART™ OPERATING INSTRUCTIONS

Special Functions

Bottle Chill (selected models only)

This function allows you to chill your beverages more rapidly in the freezer without the

worry of forgetting them. The timer is set for 15minutes however the time taken to chill

depends on the size of your beverage. If after 15minutes your beverage is not cold enough,

simply place it back in the freezer and reset the ‘Bottle Chill’ function.

zTo activate, press the button on the internal display. The ‘Bottle Chill’ light will be

illuminated when the function isactivated. The icon will be illuminated on the external

display (Ice & Water and Automatic Ice models only).

zAn alarm will sound after the 15minute time has elapsed.

z For non-Ice & Water models: open the fresh food compartment door and press

the button on the internal control panel to silence the alarm.

zFor Ice & Water models: the icon will flash on the external display. Press the

button on the external display to silence the alarm.

zRemember to remove your beverage from the freezer.

zTo deactivate ‘Bottle Chill’ before 15minutes has elapsed, press the button again on

the internal control panel. When ‘Bottle Chill’ is deactivated the light is off and the icon

is not visible on the external display (Ice & Water and Automatic Ice models only).

Fast Freeze (selected models only)

We have created the ‘Fast Freeze’ feature to help you get the best possible results when

freezing fresh food. ‘Fast Freeze’ boosts the freezing speed by dropping the freezer to its

coldest temperature for 12 hours, which helps to ensure vital freshness, texture and taste

are retained during the freezing process.

zTo activate, press the button on the internal display. The ‘Fast Freeze’ light will be

illuminated when the function isactivated.

zTo deactivate before the 12hours has elapsed, press the button again. When ‘Fast

Freeze’ is deactivated the light is off.

zFor best results we recommend that you activate the function before it is required.

Alternatively, activate it when placing food into the freezer.

Ice boost function (selected models only)

This function is designed to be used for times when you require more ice eg when you

are having a party. The ‘Ice Boost’ function will increase ice production up to 30% from

standard ice making and deactivate automatically after 24hours.

zWhen you first turn your ice maker on, the ‘Ice Boost’ function will be off.

zTo turn this function on, press the button. The light above the button will be

illuminated when the ‘Ice Boost’ function is on.

zThe ‘Ice Boost’ function is paused once your ice bin is full.

zTo manually deactivate this feature press the button again. The light above the

button will be off when the ‘Ice Boost’ function is off.

zActivating the ‘Ice Boost’ function will automatically turn ice making on.

zDeactivating ice making will automatically deactivate the ‘Ice Boost’ function.

ALL ABOUT THE EXTERNAL DISPLAY

(ICE & WATER MODELS ONLY)

This screen enables you to lock the water dispenser, indicates to you when ‘Bottle Chill’ is

activated and when your water filter requires changing.

EXTERNAL DISPLAY FEATURES

Dispenser lock button

and LED light

Locks/unlocks the water dispenser.

When locked the LED above the button

will illuminate.

Bottle Chill indicator Icon will illuminate indicating when ‘Bottle Chill’ is

activated and flashes when beverage is ready.

Filter change

indicator

Icon will illuminate indicating when water filter

requires changing.

USING YOUR WATER DISPENSER

(ICE & WATER MODELS ONLY)

Dispensing

zYour water dispenser has been designed for one-

handed operation.

zTo dispense water push the dispensing pad gently, using a glass

or container. This pad requires only a gentle press to activate.

zTo stop the flow of water, simply pull your glass away from the

dispensing pad.

Please remember that pressing very hard against the dispensing

pad will not encourage the dispenser to operate faster or produce

greater quantities of water.

First use

Before using your water dispenser, the water filter must be installed and flushed to remove

any impurities or trappedair inthe filter system. Refer to ‘Before you start using the Ice &

Water or Automatic Ice function’ for details.

IMPORTANT!

To avoid damage to property or personal injury do not put hands, fingers or objects up

the dispenser opening.

Please note that once installation is complete a few drips may appear out of the dispenser

over the next few days as the remaining trapped air is cleared.

Dispenser Lock

The ‘Dispenser Lock’ prevents water from being dispensed. This is

useful when you are cleaning the external display or when there are

small children around.

zPress and hold the button for 4 seconds to activate

‘Dispenser Lock’.

zThe light above the ‘Dispenser Lock’ icon will be illuminated.

zPressing the water dispenser pad will cause a raspberry sound

indicating to the user that water cannot be dispensed.

zTo de-activate the ‘Dispenser Lock’, press and hold the button

for 4 seconds. The light above the ‘Dispenser Lock’ icon will no

longer be illuminated and water dispensing will be enabled.

Water dispenser

Dispenser Lock

Produkt Specifikationer

Mærke:	Fisher & Paykel
Kategori:	Køleskab
Model:	E402BLXFD4
Bredde:	635 mm
Dybde:	695 mm
Højde:	1715 mm
Produktfarve:	Sølv
Lampe type:	LED
Energieffektivitetsklasse (gammel):	A+
Årligt energiforbrug:	320 kWh
Placering af apparat:	Fritstående
Tilsluttet belastning:	- W
Støjniveau:	42 dB
Fryser, netto rumindhold:	91 L
Fryser, brutto rumindhold:	- L
Frysekapacitet:	7.5 kg/24t
Opbevaringstid under strømafbrydelse:	11.5 t
Klimaklasse:	T
Køleskab antal hylder/kurve:	4
Antal grøntsagsskuffer:	2
Æggebakke:	Ja
Køleskabsdøre:	4
Køleskab, netto rumindhold:	273 L
Total netto kapacitet:	364 L
Understøtter VPN:	414 L
Køleskab indvendigt lys:	Ja
Stjernebedømmelse:	4*
Fryser position:	Bottom-placeret
Hylder, materiale:	Hærdet glas
Køleskab, brutto rumindhold:	- L
Flaskeholder:	Ja
No Frost (fryser):	Ja
Hurtig frys funktion:	Ja
Fryser antal hylder/kurve:	2
Åben dør alarm:	Ja
Isterning bakke:	Ja