FLM CP10 Manual
Læs nedenfor 📖 manual på dansk for FLM CP10 (4 sider) i kategorien Stativ. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/4
Instructions fort he adhesive assembly of the QRB and PRP
Glued Joints for FLM Centerball
The stud screw, which is supplied with the Centerball, can be screwed into the ball in two ways. With the1/4" threads
on the top, the single plate can be screwed on so that the projecting 1/4" threads can be used for the camera
connection. However, for the setup of special camera plates, the 3/8" threads must point upwards and in this case the
1/4" threads of the stud screw disappear in the ball.
In order to prevent damage to the bottom threads of the camera, you must pay particular attention to the length of the
threads, which projects outwards.
To connect the Quick-Release Basis or the Power-Release Basis (picture 2) rmly and in a manner, which will not
allow it to rotate, with the Centerball, the stud screw is glued to the basis and CenterBall. Please use themetal
adhesive with thermal stability up to about 100° C to allow later changing of your basis. We recommend UHU plus
ultimate strength 300 (UHU plus endfest 300).
Picture 1
Picture 2
Picture 3
Apply the glue to the end of the 3/8" threads about three thread turns all around (no glue on the screw head, see
picture 1) and screw this screw end in up to the stop in the Power-Release Basis. However, for the Quick-Release
Basis, the screw must not be allowed to project out of the basis plate (picture 3).
After hardening (see instructions for use of your glue), the basis is glued to the CenterBall in the same way (picture
3). You can replace your old basis plate later by completely immersing the basis plate BUT ONLY THE BASIS —
PLATE in hot boiling water. This softens the metal adhesive and the plate can be taken o easily. —
Protect your hand against burns when doing this.
Please keep care that no sand and saltwater attained
inside of the ballhead.
Warranty
We provide a 10 year warranty for material and workmanship for all FLM products.
Now, we hope you have lots of fun and enjoy the fast and secure mounting of
your camera.
Produkt Specifikationer
| Mærke: | FLM |
| Kategori: | Stativ |
| Model: | CP10 |
Har du brug for hjælp?
Hvis du har brug for hjælp til FLM CP10 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Stativ FLM Manualer
3 September 2024
Stativ Manualer
- Stativ SilverCrest
- Stativ Sony
- Stativ Easypix
- Stativ Asus
- Stativ Livoo
- Stativ Nikon
- Stativ Kodak
- Stativ Hama
- Stativ Trust
- Stativ Laserliner
- Stativ König
- Stativ Bresser
- Stativ Rollei
- Stativ DJI
- Stativ Godox
- Stativ Omnitronic
- Stativ Carson
- Stativ Celestron
- Stativ Zhiyun
- Stativ Rode
- Stativ AVerMedia
- Stativ Marshall Electronics
- Stativ GVM
- Stativ Sachtler
- Stativ Vortex
- Stativ Testo
- Stativ Barska
- Stativ ARRI
- Stativ Vinten
- Stativ Eurolite
- Stativ Kessler
- Stativ Proaim
- Stativ Manfrotto
- Stativ Kogan
- Stativ Joby
- Stativ Levenhuk
- Stativ Gravity
- Stativ Drift
- Stativ Magnus
- Stativ Konig & Meyer
- Stativ Neewer
- Stativ Easyrig
- Stativ REVO
- Stativ Glide Gear
- Stativ Miller
- Stativ Sky-Watcher
- Stativ Square Jellyfish
- Stativ Fidlock
- Stativ Robus
- Stativ Vello
- Stativ Benro
- Stativ Sunpak
- Stativ Slik
- Stativ Libec
- Stativ Gitzo
- Stativ Velbon
- Stativ Ultimate Support
- Stativ Oben
- Stativ Moza
- Stativ Vanguard
- Stativ Dorr
- Stativ Winegard
- Stativ Camgear
- Stativ Ulanzi
- Stativ Flycam
- Stativ Sirui
- Stativ Acratech
- Stativ ProMediaGear
- Stativ IOptron
- Stativ Mantona
- Stativ Olloclip
- Stativ Cullmann
- Stativ IFootage
- Stativ FeiYu-Tech
- Stativ FeiyuTech
- Stativ Hohem
- Stativ MOVE'N SEE
- Stativ On Air
- Stativ Kaiser Fototechnik
- Stativ Slidekamera
- Stativ FLOWCINE
- Stativ SteadiCam
- Stativ Fat Gecko
- Stativ 3 Legged Thing
- Stativ Peak Design
- Stativ Studio Assets
- Stativ E-Image
- Stativ Tiltall
- Stativ MotoCrane
- Stativ Really Right Stuff
- Stativ HPRC
- Stativ Cartoni
Nyeste Stativ Manualer
14 December 2024
14 December 2024
12 December 2024
12 December 2024
12 December 2024
12 December 2024
12 December 2024
12 December 2024
11 December 2024
11 December 2024