Frigidaire FDB130RGS Manual

Frigidaire Opvaskemaskine FDB130RGS

Læs nedenfor 📖 manual på dansk for Frigidaire FDB130RGS (2 sider) i kategorien Opvaskemaskine. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/2
16 3/ ”8
Before You Begin
Read all instructions before installing dishwasher.
For your safety, please read and observe all safety
instructions. This guide will help you anticipate drain, water, and
electrical connections, and help you select the best location for the
dishwasher.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Failure to follow this warning can result in serious
injury.
Figure 4
4. Cut water access hole in shaded area in Figure 2.
5. Route water supply line into installation area.
IMPORTANT: Incoming hot water temperature should be at
least 120°F (49°C). Water pressure should be between
20–120 psi.
Drain
1. Review Figures 5, 6 and 7 to see the different ways to connect
dishwasher to drain system. Choose method that best suits
your need.
2. If you connect to a sink drain, entry will need to be above
trap. A “Y” branch tailpiece and connector kit, not included, will
make this method easier and includes all needed fittings and
instructions. See Figure 5.
5.
Before cutting
drain hose access, check both sides of selected
area to avoid interference. Cut a 2” diameter hole in shaded
area shown in Figure 2.
6. If the cabinet wall is wood, sand edges of hole until smooth and
rounded. If cabinet wall is metal, cover all sharp edges with
electrical or duct tape to avoid cutting drain hose.
Installation Tips
1
Tools and Materials Needed for
Installation
• Drill, Electric
• Driver, Socket 5/32”, 1/4” , 5/16”
• Flaring Tool / Tube Cutter (for copper tubing)
• Flashlight
• Gloves
• Level
• Pipe Joint Compound (for iron pipe plumbing) or
Pipe Thread Tape (for sealing threads)
• Pliers
• Safety Glasses
• Saw, Keyhole or 1/2
”, 11/2”
to 2” Hole Cutters
• Screw Drivers, Slotted and #2 Phillips (magnetic tip
preferred)
• Tape, Electrical or Duct
• Tape, Measuring
• Wire Stripper or Utility Knife
• Wrench, Hex-end
• Wrenches, 2 Adjustable (for copper tubing)
or 2 Pipe wrenches (for iron pipe plumbing)
Electric Shock Hazard
Electrical, water, and drain lines must be confined
to shaded areas in Figure 2.
Electric conductors, water, and drain could be
damaged.
Failure to follow these instructions could result in
fire or electric shock.
NOTE: If dishwasher is installed at end of a cabinet line, sides
and back must be fully enclosed.
NOTE: You can order a Cabinet Seal Kit (Kit # 154528701) by
contacting your dealer or parts supplier. This kit provides a
seal between the unit and cabinets once installation is
complete.
IMPORTANT: Do not cross drain, water, and electrical lines in
front of dishwasher motor or frame.
4
Connections For Electrical,
Water, and Drain
Right Side
Front
Left Side
Door in
open position
Locating the Connections
1. Review dimensions in Figure 3 to locate dishwasher’s drain,
water, and electrical connections.
2. All connections must be made in shaded area in Figure 2.
25 24 49 1/ ”422 1/ ”2
3 31/2”
Min.
From rear to
center of water
inlet valve.
3 3/4”
From floor to
water inlet
valve.
Floor Line
Figure 3
Junction Box
(not visible)
17 3/ ”4
From rear to
junction box.
3. Locate water inlet valve behind kickplate on bottom left
underside of unit. The valve has a 3/8” NPT or 3/4” hose thread
fitting. Note: If using 3/4” hose thread fitting skip steps 4 and 5.
4. Wrap 90° elbow (not included) with pipe thread tape (or apply
joint compound) and thread it into water inlet valve.
5. Tighten elbow with a wrench, leaving elbow pointing toward
rear of unit.
To prevent bending of bracket or breaking of valve,
avoid overtightening.
6. If using 3/4” hose thread fitting, do not use teflon tape, tighten
elbow. Do not over tighten.
1. Remove two (2) screws at front of the kickplate assembly using
a #2 Phillips screw driver.
2. Tilt and pull forward to remove. See Figure 1.
NOTE: It is not necessary to remove the outer door for installation.
However, you might find it more convenient to do so. You
can find directions for removing door in Step 10.
Installation Preparation
2
• Examine dishwasher and locate connections.
See Step 4.
• Locate dishwasher where there is easy access to drain,
water, and electrical lines. The best location is on either side
of the kitchen sink for access to existing plumbing and ease
in loading dishes.
See Step 4.
• Electrical, water, and drain connections are not the same for
all age, brands, or models of dishwashers. Check the
location and length of home utilities.
See Step 4.
• A 15-20 amp, grounded, 120 volt AC only, electrical supply is
required.
See Steps 4 and 8.
• If dishwasher drain hose will be connected to a food
disposer for the first time, knock out plug located inside
disposer inlet.
See Steps 4 and 6.
• Kinked water or drain hoses can cause problems.
See Step
6.
• Dishwashers need to be connected to a hot water supply
with enough water pressure to insure an adequate fill.
See Steps 4 and 7.
• Each home installation differs. You will need additional
parts listed above to complete your installation.
See Steps 4 and 7.
• Flush water line prior to making the final connection to
prevent clogging of dishwasher’s filter screen.
See Step 7.
• The dishwasher will look, sound, and perform best when
properly leveled.
See Step 5.
(NOTE: If levelers are
removed during installation, make sure the floor is flat and
free of any obstruction.)
• Anchor the dishwasher.
See Step 9.
Kickplate Assembly
Figure 1
Bottom Screws
(Insulation available
some models)
Kickplate
Water Inlet
Valve
Entry Must be
Above Trap
Sink at Left
Sink at Right
“Y”
Branch
Tailpiece
2” Drain Hose Hole
Figure 5
Sink at Right
Remove
Knockout
Plug in
Disposer 2” Drain Hose Hole
Figure 7(b)
Parts You Will Need* (Not Included)
• Drain Hose Clamp, 11/4” Diameter
• Elbow, 90° with a 3/8” National Pipe Thread or 3/4” Hose Thread
Fitting
•Conduit Connector
• Wire Nuts, two (2) for 12-14 gauge wire
• Plumbers Tape
*
If required: Available at:
• “Y” Branch Tailpiece and Plumbing Supply Store
Connector Kit (See Step 4)
• Air Gap Kit (See Step 4) Plumbing Supply Store
• Fasteners for floor Hardware Store
anchoring (See Step 9)
IMPORTANT: Disconnect power before starting installation.
Electrical
1. The dishwasher operates on a 120 volt, 60 Hz electrical supply.
Provide a separate circuit with a fuse or circuit breaker rated for
at least 15 amps (20 amps if connected with disposer) but not
more than 20 amps.
2. Note the locations of electrical supply and dishwasher’s
electrical junction box on right underside of unit behind kickplate
assembly. See Figure 3.
3. Cut access hole in shaded area shown in Figure 2.
4. Pull electrical cable through hole into installation area.
Water
1. Determine where you will connect to hot water supply. Review
Figure 3 and note the location of water inlet valve.
Property Damage
Do not use the furnished drain hose or a rubber garden hose
for the water supply line. Either of these hoses can burst.
Flooding may occur and cause property damage.
3. If you connect to a sink trap, local codes may require you to
install an air gap kit, (not included). The drain hose will be routed
from dishwasher to air gap inlet as shown in Figure 6. An air
gap kit is available from a plumbing supply store. NOTE: If the
drain hose is installed through the floor, an air
gap is necessary.
4. If you connect to a disposer, the large end of drain hose will
fit. Figure 7(a).
The knock out plug must be removed from
inside disposer inlet before making the final fit to drain
hose.
See Figure 7(b).
3
Roughing In
Electric Shock Hazard
Observe all local codes and ordinances for
electrical and plumbing connections. All electrical
and plumbing work should be performed by
qualified persons. Failure to follow this warning
could result in death or serious injury.
1. Make sure your location has the right drain, water, and electrical
outlets to make the connections.
Do not install unit under a
cooktop range. Damage to plastic tub will occur.
90° 90°
21/ ”2
6”
24”
6”
21 / 2 ”
73/4”
Hot
Water
Line
Electrical
Wiring
▲▲▲▲▲
▲▲▲▲▲
3”
4”
24”
min.
18”
Electrical, water,
and drain lines
must be confined
to shaded area.
Figure 2
Through
Cabinet
2. Be sure water inlet valve is protected from freezing. If valve
freezes and ruptures, flooding may occur.
3. Determine amount of tubing needed to connect hot water
supply to the unit’s water inlet valve. Copper tubing must have a
minimum
3/8” OD. High-pressure and high-temperature rated
plastic tubing with a minimum inner diameter of
1/4” may be
used. A shut-off valve installed outside dishwasher cabinet is
best. See Figure 4.
34
1
/4” min.
IMPORTANT: For proper operation and appearance of unit,
cabinet opening should have dimensions as shown in Figure 2.
If unit is to be placed in a corner, there must be at least a 2-inch
side clearance to open door.
2. Remove any carpet from area to provide motor clearance.
Floor
should be flat and free of any obstruction.
IMPORTANT: Drain, water, and electrical lines should be
roughed-in before going any further.
Air Gap
Figure 6
INSTALLER: Leave
Installation Instructions
with owner.
OWNER: Read your dishwasher
Use and Care Manual.
It contains
important safety information for operating this appliance. It also has
many suggestions for getting the best results from your dishwasher.
Dishwasher
Installation
Instructions
Electric Shock Hazard
Disconnect electrical power at the fuse box or
circuit breaker box before beginning installation.
Failure to follow this warning could result in death
or serious injury.
Right Side
Installation
Cut for
5/8” connection.
Drain
Motor
End
Cut for 3/4” connection.
Figure 7(a)
Larger end
of hose
fits disposer
inlet fitting.
PN: 154427301/G
AW: 154427301/007
5/14
Printed in U.S.A.
Drain Air Gap
Sink at Left
Alternate
Drain
Through
Floor into
Separate
Trap
Drain Hose
Adjustable Toeplate
Cabinet Preparation:
As a precaution, it is recommended, but not required that the cabinets
enclosing all sides of the dishwasher (including the underside of the
countertop) be sealed with an oil based paint or moisture-proof
polyurethane to prevent possible steam/moisture damage. *DIMENSIONS DO NOT INCLUDE INSULATION
NOTE: Recommended to use Stainless Steel braded hose.
Drying Vent Hose (if equipped)
Care must be given during installation and removal of the dishwasher
to avoid disconnection of the vent hose that is attached to the top of
the dishwasher.
Drying Vent
Hose

Produkt Specifikationer

Mærke: Frigidaire
Kategori: Opvaskemaskine
Model: FDB130RGS

Har du brug for hjælp?

Hvis du har brug for hjælp til Frigidaire FDB130RGS stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine Frigidaire Manualer

Frigidaire

Frigidaire FBD2400KQ Manual

7 Oktober 2024
Frigidaire

Frigidaire PLD2885RFC Manual

23 September 2024
Frigidaire

Frigidaire FFBD1831UW Manual

22 September 2024
Frigidaire

Frigidaire FDB1502RGQ Manual

20 September 2024
Frigidaire

Frigidaire FD 604Z Manual

17 September 2024
Frigidaire

Frigidaire FFBD2404NS Manual

17 September 2024
Frigidaire

Frigidaire FGIP2479SF Manual

17 September 2024
Frigidaire

Frigidaire FGHD2472PW Manual

13 September 2024
Frigidaire

Frigidaire FDB1500LFC Manual

13 September 2024
Frigidaire

Frigidaire PLD3460RDC Manual

9 September 2024

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Siemens

Siemens SN45M283SK Manual

3 December 2024
Bosch

Bosch SGS44E72EU Manual

29 November 2024
Samsung

Samsung DW60M9550BB Manual

26 November 2024
Bosch

Bosch SMS63M18AU Manual

26 November 2024
Kogan

Kogan KABNCHTPDWA Manual

26 November 2024
Siemens

Siemens SX64M080EU Manual

26 November 2024
Bosch

Bosch SGU53E15AU Manual

25 November 2024
Samsung

Samsung DW60M5044FS Manual

24 November 2024
Samsung

Samsung DW60DG550B00 Manual

24 November 2024
Samsung

Samsung DW60DG540FSR Manual

24 November 2024