Frigidaire FPID2486TF Manual

Frigidaire Opvaskemaskine FPID2486TF

Læs nedenfor 📖 manual på dansk for Frigidaire FPID2486TF (4 sider) i kategorien Opvaskemaskine. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

16 3/ ”8

Before You Begin

Read all instructions before installing dishwasher.

For your safety, please read and observe all safety

instructions. This guide will help you anticipate drain, water, and

electrical connections, and help you select the best location for the

dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Failure to follow this warning can result in serious

injury.

Figure 4

4. Cut water access hole in shaded area in Figure 2.

5. Route water supply line into installation area.

IMPORTANT: Incoming hot water temperature should be at

least 120°F (49°C). Water pressure should be between

20–120 psi.

Drain

1. Review

Figures 5, 6

and 7 to see the different ways to connect

dishwasher to drain system. Choose method that best suits

your need.

2. If you connect to a sink drain, entry will need to be above

trap. A “Y” branch tailpiece and connector kit, not included, will

make this method easier and includes all needed fittings and

instructions. See Figure 5.

5. Before cutting drain hose access, check both sides of selected

area to avoid interference. Cut a 2” diameter hole in shaded

area shown in Figure 2.

6. If the cabinet wall is wood, sand edges of hole until smooth and

rounded. If cabinet wall is metal, cover all sharp edges with

electrical or duct tape to avoid cutting drain hose.

Installation Tips 1

Tools and Materials Needed for

Installation

• Drill, Electric

• Driver, Socket 5/32”, 1/4” , 5/16”

• Flaring Tool / Tube Cutter (for copper tubing)

• Flashlight

• Gloves

• Level

• Pipe Joint Compound (for iron pipe plumbing) or

Pipe Thread Tape (for sealing threads)

• Pliers

• Safety Glasses

• Saw, Keyhole or 1/2

”, 11/2”

to 2” Hole Cutters

• Screw Drivers, Slotted and #2 Phillips (magnetic tip

preferred)

• Tape, Electrical or Duct

• Tape, Measuring

• Wire Stripper or Utility Knife

• Wrench, Hex-end

• Wrenches, 2 Adjustable (for copper tubing)

or 2 Pipe wrenches (for iron pipe plumbing)

Electric Shock Hazard

Electrical, water, and drain lines must be confined

to shaded areas in Figure 2.

Electric conductors, water, and drain could be

damaged.

Failure to follow these instructions could result in

fire or electric shock.

NOTE: If dishwasher is installed at end of a cabinet line, sides

and back must be fully enclosed.

NOTE: You can order a Cabinet Seal Kit (Kit # 154528701) by

contacting your dealer or parts supplier. This kit provides a

seal between the unit and cabinets once installation is

complete.

IMPORTANT: Do not cross drain, water, and electrical lines in

front of dishwasher motor or frame.

Connections For Electrical,

Water, and Drain

Right Side

Front

Left Side

Door in

open position

Locating the Connections

1. Review dimensions in Figure 3 to locate dishwasher’s drain,

water, and electrical connections.

2. All connections must be made in shaded area in Figure 2.

25 24 49 1/ ”422 1/ ”2

3 31 / 2”

Min.

From rear to

center of water

inlet valve.

3 3/4”

From floor to

water inlet

valve.

Floor Line

Figure 3

Junction Box

(not visible)

17 3/ ”4

From rear to

junction box.

3. Locate water inlet valve behind kickplate on bottom left

underside of unit. The valve has a 3/8” NPT or 3/4” hose thread

fitting. Note: If using 3/4” hose thread fitting skip steps 4 and 5.

4. Wrap 90° elbow (not included) with pipe thread tape (or apply

joint compound) and thread it into water inlet valve.

5. Tighten elbow with a wrench, leaving elbow pointing toward

rear of unit. To prevent bending of bracket or breaking of valve,

avoid overtightening.

6. If using 3/4” hose thread fitting, do not use teflon tape, tighten

elbow. Do not over tighten.

1. Remove two (2) screws at front of the kickplate assembly using

a #2 Phillips screw driver.

2. Tilt and pull forward to remove. See Figure 1.

NOTE: It is not necessary to remove the outer door for installation.

However, you might find it more convenient to do so. You

can find directions for removing door in Step 10.

Installation Preparation 2

• Examine dishwasher and locate connections. See Step 4.

• Locate dishwasher where there is easy access to drain,

water, and electrical lines. The best location is on either side

of the kitchen sink for access to existing plumbing and ease

in loading dishes. See Step 4.

• Electrical, water, and drain connections are not the same for

all age, brands, or models of dishwashers. Check the

location and length of home utilities. See Step 4.

• A 15-20 amp, grounded, 120 volt AC only, electrical supply is

required. See Steps 4 and 8.

• If dishwasher drain hose will be connected to a food

disposer for the first time, knock out plug located inside

disposer inlet. See Steps 4 and 6.

• Kinked water or drain hoses can cause problems. See Step

• Dishwashers need to be connected to a hot water supply

with enough water pressure to insure an adequate fill.

See Steps 4 and 7.

• Each home installation differs. You will need additional

parts listed above to complete your installation.

See Steps 4 and 7.

• Flush water line prior to making the final connection to

prevent clogging of dishwasher’s filter screen. See Step 7.

• The dishwasher will look, sound, and perform best when

properly leveled. See Step 5. (NOTE: If levelers are

removed during installation, make sure the floor is flat and

free of any obstruction.)

• Anchor the dishwasher. See Step 9.

Kickplate Assembly

Figure 1

Bottom Screws

(Insulation available

some models)

Kickplate

Water Inlet

Valve

Entry Must be

Above Trap

Sink at Left

Sink at Right

“Y”

Branch

Tailpiece

2” Drain Hose Hole

Figure 5

Sink at Right

Remove

Knockout

Plug in

Disposer 2” Drain Hose Hole

Figure 7(b)

Parts You Will Need* (Not Included)

• Drain Hose Clamp, 11/4” Diameter

• Elbow, 90° with a 3/8” National Pipe Thread or 3/4” Hose Thread

Fitting

• Conduit Connector

• Wire Nuts, two (2) for 12-14 gauge wire

• Plumbers Tape

* If required: Available at:

• “Y” Branch Tailpiece and Plumbing Supply Store

Connector Kit (See Step 4)

• Air Gap Kit (See Step 4) Plumbing Supply Store

• Fasteners for floor Hardware Store

anchoring (See Step 9)

IMPORTANT: Disconnect power before starting installation.

Electrical

1. The dishwasher operates on a 120 volt, 60 Hz electrical supply.

Provide a separate circuit with a fuse or circuit breaker rated for

at least 15 amps (20 amps if connected with disposer) but not

more than 20 amps.

2. Note the locations of electrical supply and dishwasher’s

electrical junction box on right underside of unit behind kickplate

assembly. See Figure 3.

3. Cut access hole in shaded area shown in Figure 2.

4. Pull electrical cable through hole into installation area.

Water

1. Determine where you will connect to hot water supply. Review

Figure 3 and note the location of water inlet valve.

Property Damage

Do not use the furnished drain hose or a rubber garden hose

for the water supply line. Either of these hoses can burst.

Flooding may occur and cause property damage.

3. If you connect to a sink trap, local codes may require you to

install an air gap kit, (not included). The drain hose will be routed

from dishwasher to air gap inlet as shown in Figure 6. An air

gap kit is available from a plumbing supply store. NOTE: If the

drain hose is installed through the floor, an air

gap is necessary.

4. If you connect to a disposer, the large end of drain hose will

fit. Figure 7(a). The knock out plug must be removed from

inside disposer inlet before making the final fit to drain

hose. See Figure 7(b).

Roughing In

Electric Shock Hazard

Observe all local codes and ordinances for

electrical and plumbing connections. All electrical

and plumbing work should be performed by

qualified persons. Failure to follow this warning

could result in death or serious injury.

1. Make sure your location has the right drain, water, and electrical

outlets to make the connections. Do not install unit under a

cooktop range. Damage to plastic tub will occur.

90° 90°

21/ ”2

6”

24”

6”

21 / 2 ”

73/4”

Hot

Water

Line

Electrical

Wiring

▲▲▲▲▲

3”

4”

24”

min.

18”

Electrical, water,

and drain lines

must be confined

to shaded area.

Figure 2

Through

Cabinet

2. Be sure water inlet valve is protected from freezing. If valve

freezes and ruptures, flooding may occur.

3. Determine amount of tubing needed to connect hot water

supply to the unit’s water inlet valve. Copper tubing must have a

minimum

3/8” OD. High-pressure and high-temperature rated

plastic tubing with a minimum inner diameter of

1/4” may be

used. A shut-off valve installed outside dishwasher cabinet is

best. See Figure 4.

/4” min.

IMPORTANT: For proper operation and appearance of unit,

cabinet opening should have dimensions as shown in Figure 2.

If unit is to be placed in a corner, there must be at least a 2-inch

side clearance to open door.

2. Remove any carpet from area to provide motor clearance. Floor

should be flat and free of any obstruction.

IMPORTANT: Drain, water, and electrical lines should be

roughed-in before going any further.

Air Gap

Figure 6

INSTALLER: Leave Installation Instructions with owner.

OWNER: Read your dishwasher Use and Care Manual. It contains

important safety information for operating this appliance. It also has

many suggestions for getting the best results from your dishwasher.

Dishwasher

Installation

Instructions

Electric Shock Hazard

Disconnect electrical power at the fuse box or

circuit breaker box before beginning installation.

Failure to follow this warning could result in death

or serious injury.

Right Side

Installation

Cut for

5/8” connection.

Drain

Motor

End

Cut for 3/4” connection.

Figure 7(a)

Larger end

of hose

fits disposer

inlet fitting.

PN: 154427301/H

AW: 154427301/008

4/15

Printed in U.S.A.

Drain Air Gap

Sink at Left

Alternate

Drain

Through

Floor into

Separate

Trap

Drain Hose

Adjustable Toeplate

Cabinet Preparation:

As a precaution, it is recommended, but not required that the cabinets

enclosing all sides of the dishwasher (including the underside of the

countertop) be sealed with an oil based paint or moisture-proof

polyurethane to prevent possible steam/moisture damage. *DIMENSIONS DO NOT INCLUDE INSULATION

NOTE: Recommended to use Stainless Steel braded hose.

Drying Vent Hose (if equipped)

Care must be given during installation and removal of the dishwasher

to avoid disconnection of the vent hose that is attached to the top of

the dishwasher.

Drying Vent

Hose

Produkt Specifikationer

Mærke:	Frigidaire
Kategori:	Opvaskemaskine
Model:	FPID2486TF

Har du brug for hjælp?

Hvis du har brug for hjælp til Frigidaire FPID2486TF stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Opvaskemaskine Frigidaire Manualer

Frigidaire FBD2400KQ Manual

7 Oktober 2024

Frigidaire PLD2885RFC Manual

23 September 2024

Frigidaire FFBD1831UW Manual

22 September 2024

Frigidaire FDB1502RGQ Manual

20 September 2024

Frigidaire FD 604Z Manual

17 September 2024

Frigidaire FFBD2404NS Manual

17 September 2024

Frigidaire FGIP2479SF Manual

17 September 2024

Frigidaire FGHD2472PW Manual

13 September 2024

Frigidaire FDB1500LFC Manual

13 September 2024

Frigidaire PLD3460RDC Manual

9 September 2024

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

21 November 2024

21 November 2024

21 November 2024

21 November 2024

Bosch SMU50E65AU Manual

20 November 2024

Caple DI654 Manual

18 November 2024

Teka DW8 55 FI Manual

16 November 2024

Bosch Serie 6 SMV68MX00E Manual

16 November 2024

Whirlpool WFO 3T233 P 6.5 X Manual

16 November 2024

Electrolux EEEM9420L Manual

15 November 2024