Furuno FAPAR4502 Manual

Furuno Marine FAPAR4502

Læs nedenfor 📖 manual på dansk for Furuno FAPAR4502 (2 sider) i kategorien Marine. Denne guide var nyttig for 4 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Before you do it your way,
please try it our way
TELEFLEX CANADA
3831 NO.6 ROAD
RICHMOND, B.C.
CANADA V6V 1P6
FAX 604-270-7172
www.seastarsteering.com
© 2005 TELEFLEX CANADA LIMITED PARTNERSHIP
PRINTED IN CANADA
FORM NO. 269064 - 03/06 Rev C
ISO 10592
INSTALLATION INSTRUCTIONS
SUPPLEMENTAL
20
Autopilot Rudder Reference
SMART
STICK
ISO 9001
MANUFACTURED BY
TELEFLEX CANADA LIMITED
PARTNERSHIP
HYDRAULIC
INSTALLATION INSTRUCTIONS
1Remove the nuts and washers
(item 1 & 2) from the steering
cylinder rod. Discard washers
(item 2) as they will not be used
in the SmartStick installation.
2Install brackets (item 3) onto the
ends of the cylinder support rod.
Re-install the nuts (item 1) and
torque to 33 in. lb. (3.82 Nm).
3Install the sensor (item 4) behind
the brackets as shown in figures
A and B.
4Mount the magnet (item 5) to the
center of the cylinder body with the
arrow pointed in the same direction
as the arrow on the sensor.
5Turn steering cylinder so that the
magnet arrow and the sensor decal
arrow are nearest each other.
6Without changing the position
along the length of the cylinder,
rotate the magnet on the cylinder
so that the arrows on the sensor
and magnet are as closely lined
up as possible.
7Tighten band clamp to 3 in. lb.
(0.35 Nm) to secure the magnet
in position.
Correct installation of the magnet
is important to the overall
operation of the autopilot.
Over tightening clamp may cause
magnet to break.
8Connect Rudder Reference to
autopilot as per autopilot instal-
lation instructions. Refer to Table
1 to ensure correct application
9Move the steering cylinder from
hard over to hard over to confirm
that the autopilot receives a
signal from the sensor at ALL
cylinder positions.
10
Install Strain relief (item 6).
Failure to install the strain relief
may result in irreparable damage
to the sensor.
NOTICE NOTICE
NOTICE
TOOLS REQUIRED
5/8" Wrench 5/16" Wrench
11/32" Wrench 3/32" Allen Key
Torque Wrench


Produkt Specifikationer

Mærke: Furuno
Kategori: Marine
Model: FAPAR4502

Har du brug for hjælp?

Hvis du har brug for hjælp til Furuno FAPAR4502 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Marine Furuno Manualer

Furuno

Furuno DRS4A Manual

21 August 2024
Furuno

Furuno FS-5075 Manual

21 August 2024
Furuno

Furuno 1933C-BB Manual

20 August 2024
Furuno

Furuno 1621MK2 Manual

17 August 2024
Furuno

Furuno FAX-30 Manual

16 August 2024
Furuno

Furuno FA150 Manual

12 August 2024
Furuno

Furuno 1731 Manual

12 August 2024

Marine Manualer

Nyeste Marine Manualer

Simrad

Simrad NSS Chartplotter Manual

23 September 2024
Rockford Fosgate

Rockford Fosgate PMX-2 Manual

21 September 2024
Simrad

Simrad NSS Manual

18 September 2024
Silva

Silva S15 Manual

27 August 2024
Silva

Silva S15-N Navtex Manual

27 August 2024
IVT

IVT 8A Solar Manual

26 August 2024