GBC SureBind System 2 Manual

GBC Indbindingsmaskine SureBind System 2

Læs gratis den danske manual til GBC SureBind System 2 (3 sider) i kategorien Indbindingsmaskine. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9 anmeldelser. Har du et spørgsmål om GBC SureBind System 2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
SYSTEM TWO
OPERATING INSTRUCTIONS
Punching
1. Adjust the punch edge guide to the correct paper length. Check the punch
alignment by punching a sheet of paper and folding it in half along the
punched edge (See Figure 4-1). Match the holes up; if the corners of the
paper match with no overlap, the alignment is correct. If not, readjust the
guide and repeat the process until the edges are square.
2. Place the paper fully in the punch throat, slide the paper to the left against
the punch edge guide, and press the punch button.
3. To prevent jamming, only 22 sheets of 20 pound bond paper should be
punched at one time (fewer sheets if the paper is heavier). Punch one 22
sheet segment of your document at a time, and stack the punched sections
on the binding surface. Do not punch more than 4 composition covers or 3
plastic covers at one time.
4. If you try to punch too much paper the Jam-Stopper feature will sense the
high paper load, retract the punch pins, and you will hear a beeping sound.
Simply separate the paper stack, and punch fewer pages at a time.
Figure 4-1
SYSTEM TWO
OPERATING INSTRUCTIONS
Document Assembly
1. Check the bind edge guide alignment by inserting a receiving strip in the
strip recess area. Lay a sheet of correctly aligned punched paper on the
strip, matching up the holes and the strip so that the strip is not showing at
the top or the bottom of the paper. Adjust the bind edge guide if necessary
by sliding the guide to the edge of the paper.
2. Place the back cover (face down), the punched sheets (last page on the
bottom), and front cover (face up) on top of the receiving strip.
3. Place the receiving strip (bottom binding strip with holes), textured side
down in the strip recess, located in front of the backstop. Be sure the small
hole in the receiving strip is over the locating pin. The locating pin is
on the left hand side of the strip recess area in front of the backstop.
The locating pin fits into the small hole in the plastic strip. The strip is
positioned correctly over the locating pin when it is difficult to slide the
strip to the right. Failure to properly align the strip can cause machine
damage.
4. Now determine the correct size of the pin strip. Use the scale on the
backstop to determine the thickness of the document and the size of the
pins required. Insert the strip through the document's holes and the
receiving strip.
Figure 4-2

Produkt Specifikationer

Mærke: GBC
Kategori: Indbindingsmaskine
Model: SureBind System 2

Har du brug for hjælp?

Hvis du har brug for hjælp til GBC SureBind System 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Indbindingsmaskine GBC Manualer

GBC

GBC SureBind 500 Manual

5 August 2024
GBC

GBC CombBind 200 Manual

28 Juli 2024
GBC

GBC ClickBind 150 Manual

26 Juli 2024
GBC

GBC ClickMan Manual

26 Juli 2024
GBC

GBC WireBind EKaro 40Pro Manual

24 Juli 2024
GBC

GBC ClickBind 150E Manual

24 Juli 2024
GBC

GBC SureBind System 2 Manual

23 Juli 2024
GBC

GBC C200E Manual

22 Juli 2024
GBC

GBC CombBind C100 Manual

10 Juli 2024

Indbindingsmaskine Manualer

Nyeste Indbindingsmaskine Manualer

United Office

United Office IAN 66068 Manual

1 September 2024
Pavo

Pavo Smartmaster 2 Manual

29 August 2024
Pavo

Pavo Sohomaster Manual

29 August 2024
Pavo

Pavo Wiremaster Manual

29 August 2024
Exibel

Exibel LA4J Manual

22 August 2024
Peach

Peach PB200-09 Manual

8 August 2024
Fellowes

Fellowes Metal 25 Manual

27 Juli 2024
Fellowes

Fellowes Orion 500 Manual

23 Juli 2024
Fellowes

Fellowes Lyra 3-in-1 Manual

21 Juli 2024
Leitz

Leitz Wirebind 500 Manual

20 Juli 2024