GE Profile PTD60GBPRDG Manual

GE Tørretumbler Profile PTD60GBPRDG

Læs nedenfor 📖 manual på dansk for GE Profile PTD60GBPRDG (68 sider) i kategorien Tørretumbler. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/68
Installation
Dryer
Instructions
If you have any questions, call GE Appliances at 800.GE.CARES
(800.432.2737) or GEAppliances.com visit our Website at:
In Canada, call 800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions for
local electrical inspector’s use.
IMPORTANT Observe all governing
codes and ordinances.
Install the clothes dryer according to the
manufacturer’s instructions and local codes.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions for
future reference.
Clothes dryer installation must be performed by a
qualified installer.
This dryer must be exhausted to the outdoors.
Before the old dryer is removed from service or
discarded, remove the dryer door.
Service information and the wiring diagram are
located in the control console.
Do not allow children on or in the appliance. Close
supervision of children is necessary when the
appliance is used near children.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty.
Install the dryer where the temperature is above
50°F for satisfactory operation of the dryer control
system.
Remove and discard existing plastic or metal foil
duct and replace with UL-listed duct.
- Risk of Fire
Clothes dryer installation must be performed by a
qualified installer.
Install the clothes dryer according to these
instructions and local codes.
DO NOT install a clothes dryer with flexible plastic
venting materials. If flexible metal (semi-rigid or
foil-type) duct is installed, it must be UL-listed and
installed in accordance with the instructions found
in “Connecting the Dryer to House Vent” later in
this manual. Flexible venting materials are known
to collapse, be easily crushed and trap lint. These
conditions will obstruct dryer airflow and increase
the risk of fire.
DO NOT install or store this appliance in any
location where it could be exposed to water or
weather.
To reduce the risk of severe injury or death, follow
all installation instructions.
Save these instructions. (Installers: Be sure to
leave these instructions with the customer.)
WARNING
In the Commonwealth of Massachusetts,
the following installation instructions apply:
Installation must be performed by a qualified or
licensed contractor, plumber, or gasfitter qualified
or licensed by the State.
If using a ball valve, it shall be a T-handle type.
A flexible gas connector, when used, must not
exceed 4 feet (1.2 m).
FOR GAS DRYERS ONLY
12-21 GEA
31-3000245-2


Produkt Specifikationer

Mærke: GE
Kategori: Tørretumbler
Model: Profile PTD60GBPRDG

Har du brug for hjælp?

Hvis du har brug for hjælp til GE Profile PTD60GBPRDG stil et spørgsmål nedenfor, og andre brugere vil svare dig




Tørretumbler GE Manualer

GE

GE GFD40ESCMWW Manual

15 December 2024
GE

GE SBSD137HWW Manual

9 December 2024
GE

GE SBSD137HMS Manual

7 December 2024
GE

GE FPDW1 Manual

7 December 2024
GE

GE GTX33 Manual

1 December 2024
GE

GE GFDS170 Manual

1 December 2024
GE

GE DDG9580R Manual

1 December 2024
GE

GE GFDS175 Manual

1 December 2024
GE

GE HTX26GASWWS Manual

26 November 2024
GE

GE GTDX400EDWS Manual

24 November 2024

Tørretumbler Manualer

Nyeste Tørretumbler Manualer

LG

LG RH90V9ZVEN Manual

19 December 2024
LG

LG TD-C70030EB Manual

19 December 2024
LG

LG RH80V5AV0N Manual

19 December 2024
Whirlpool

Whirlpool awz 8813 Manual

18 December 2024
Bosch

Bosch WTN832M1NL Manual

18 December 2024
Altus

Altus ADP80W Manual

17 December 2024
Ufesa

Ufesa Pro Ionic Style Manual

17 December 2024
Ufesa

Ufesa Pro Ionic-Shine Manual

17 December 2024
Haier

Haier HD100-A3959E-IT Manual

17 December 2024
Haier

Haier HD110-A3959E-IT Manual

17 December 2024