Geba Tronic TCS - Cody - Light Manual

Geba Tronic Garage døråbner TCS - Cody - Light

Læs gratis den danske manual til Geba Tronic TCS - Cody - Light (2 sider) i kategorien Garage døråbner. Denne vejledning er vurderet som hjælpsom af 100 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 50.5 anmeldelser. Har du et spørgsmål om Geba Tronic TCS - Cody - Light, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Instructions for Assembly and Use

TCS - Cody - Light

Electronic encoder-type lock for garage door drives

The TCS-Cody-Light is a modern and safe alternative to traditional key switches.

The TCS-Cody-Light can safely be used after programming the pass code. For ope-

ning or closing of the door only a four- or ﬁve-digit numeral code (pass code) has to

be entered.

After correct input of the pass code and pushing the key button the drive is trigge-

red by the potential free relay contact.

Assembly Instructions

Assembly of the CODY keyboard:

1. By slightly pushing the two latches at the right and left side of the keyboard

from behind to the edge, remove the small frame from the keyboard.

2. Now you see two ﬁxingholes (diam. = 4 mm) at the front of the keyboard.

By means of these you can ﬁx the keyboard onto the wall.

3. Connect the keyboard to the logic unit by means of the twin-cable (up to 5 m long).

There is no particular polarity for the twin wires.

4. Now re-ﬁx the small frame.

5. It is possible to connect in parallel up to four keyboards if a thin connection cable, max.

total line cross-section 1.5 mm2, is used.

Keyboards connected in this way must not be operated simultaneously.

Assembly of the logic unit (inside area):

1. Put the screw-driver into the gap of the enclosure front, push the screw-driver up and

open the enclosure.

2. Remove the control PCB (which is force ﬁtted to the inside of the enclosure).

3. Locate the screwed glands supplied (sealing nipple left side) in the

enclosure and replace the PCB. (Please ensure PCB is ﬁrmly in position)

4. Bore the fastening holes and ﬁx the enclosure bracket at the wall.

5. The wires for the keyboard ensure through the left cable entry (sealing nipple), the wires

for the relay contact through the middle cable entry and the wires for the supply voltage

ensure through the right cable entry. Ensure tight seating of sealing nipple and cable

gland, otherwise the water-protection ot the appliance cannot be assured.

6. According to connection diagram connect the wires to the corresponding terminals.

geba GmbH is released of its obligations regarding guarantee and product liability if - without prior

permission - the unit has been modified, or if the installation is unproper or not in accordance with

our instruction manual. The installer has to take care that the EMC-regulations are respected.

Technical Data:

24 V series 240 V series

Supply voltage 24 V AC / DC 240 V AC 50 Hz

Output 1x NO, NC relay contact, isolated, 8 A 250 V

Connections 2.5 mm2max.,

Ambient- -20 ˚C to +60 ˚C

temperature

The most important characteristics of the TCS-Cody -Light are:

➢Simple operation, programming and assembly.

➢Water-protected enclosure.

➢A maximum of safety:

➢ The electronic decoder is separately installed in the

protected area

➢4 different pass codes can be stored

Appliance blocking function for the case of attempted manipulation

Nearly unlimited data security, even with power failure

➢High switching capacity for direct control of appliances

industial controls

Description of the appliance

The TCS-Cody-Light consists of a decoder and a keyboard. These units are connected by a

simple double-wire cable without a special plug. The appliance connected, in most cases a

door drive, is controlled by the input of a correct pass code.

Passing

code:

The pass code is either a four- or ﬁve-digit numeral code, by which you operate your

door drive unit. You have the possibility to store up to four diﬀerent pass codes, which

means that up to four diﬀerent persons with different pass codes can open the door. In case

you are accompanied by another person when entering your passing code you can at

ﬁrst press as many keys as you like before you ﬁnally enter your code. This ensures that

no other person can notice your pass code. Nevertheless, the TCS-Cody recognizes your

pass code as correct! The TCS-Cody is preset by the company with the pass code 1234 on

memory location 01.

Blocking

function:

For reasons of safety during attempts of manipulation the TCS-Cody -Light automatically

blocks for 10 seconds after the input of a wrong pass code which is signalled with a

double sound signal. The end of the blocking time is signalled by a long sound signal.

Programming:

The appliance is programmed with four possible pass codes. The logic unit is ﬁtted with

DIP SWITCHES (see ﬁgure below). Those four switches correspond to the four memory

locations for the individual pass codes.

In order to input a pass code set the corresponding switch to programming position

(ON-position). At the keyboard now enter the desired four- or ﬁve-digit new code and

actuate the key-operated push button. hen set the switch back to normal operating T

position. The relay now attracts and the door opens.

Any previously stored code in this position is now overwritten.

This procedure can now be repeated for the other three items.

iptomatic:

Especially for garage doors the TCS-Cody is designed with TIPTOMATIC-timing. After

input of a pass code and within a period of 60 seconds this function allows to control the

door with any key, except for the button, and without the need to enter the pass

code once again. This isolating facility can, however, be interrupted prior to the expiration

of the 60 seconds, by pressing the button.

Spannungsversorgung

je nach Gerätetyp

Tastatur

Tor 1

Trafo

L1 N PE

DIP-Schalter

1 2 3 4

Connection diagram:

Dear customer,

The Cody which you have purchased is one of our highest quality technical pro-

ducts. We have taken the greatest care in its manufacture to ensure that this

microprocessor controlled encoder reaches you in faultless condition. However in

the unusual event of suspected equipment failure please return the appliance

together with the enclosed warranty document to your dealer or direct to our

factory.

The extent of warranty exclusively refers to the free repair of malfunctions of the

appliance, which demonstrably are caused by faults in production or defective

material, inclusive of spare parts required for this purpose.

Therefore please ﬁrst read the instructions of use carefully before you start

programming !!!

Warranty-document

On the below described encoder we grant a warranty of

1 year

Type: TCS - Cody - Light

Production date: ____________________________________________________

Sales date: ____________________________________________________

Dealers adress:

DIP SWITCHES

garage door

power supply

keyboard

Trans-

former

industial controls

Produkt Specifikationer

Mærke:	Geba Tronic
Kategori:	Garage døråbner
Model:	TCS - Cody - Light

Har du brug for hjælp?

Hvis du har brug for hjælp til Geba Tronic TCS - Cody - Light stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Garage døråbner Geba Tronic Manualer

Geba Tronic TCS - Cody - Light Manual

26 Januar 2023

Geba Tronic ROLLOTIMER Standard Manual

18 December 2022

Geba Tronic TCS - Cody 1- 1 Manual

7 December 2022

Geba Tronic DC2 ECO Manual

25 Oktober 2022

Geba Tronic DC 2 EN ECO Manual

22 Oktober 2022

Geba Tronic DC MiniMax 3 S Manual

21 Oktober 2022

Geba Tronic TCS - Cody 2 Manual

7 Oktober 2022

Garage døråbner Manualer

Nyeste Garage døråbner Manualer

Sommer S 9080 pro+ S3 Manual

2 September 2025

Schellenberg Smart Drive XL Manual

17 August 2025

MSW -GDOOR-005B Manual

17 August 2025

MSW -GDOOR-002A Manual

17 August 2025

MSW -GDOOR-003B Manual

17 August 2025

MSW -GDOOR-001A Manual

17 August 2025

Schellenberg Drive Action Manual

16 August 2025

MSW -GDOOR-003A Manual

15 August 2025

Sommer S 9080 tiga+ Manual

14 August 2025

Sommer Marathon 550 SL Manual

13 August 2025