Gigabyte G150-B10 Manual

Gigabyte Server G150-B10

Læs nedenfor 📖 manual på dansk for Gigabyte G150-B10 (2 sider) i kategorien Server. Denne guide var nyttig for 14 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Motherboard Components/ 主板组件

No. Code Descripon

1 CPU Intel Xeon® processor D-1541, FCBGA1667 SoC (MB10-DS3)

2 SFP+1_2 SFP+ connectors #1/#2

3 LAN1_2 LAN ports

4 USB3_MLAN BMC Management LAN port (top) / USB 3.0 ports (boom)

5 CPU0_FAN CPU fan connector

6 VGA VGA port

7 SW_ID ID switch buon w/LED

8 SW_PWR Power buon w/LED

9 LED_STA System Status LED

10 P12V_AUX1 8 pin power connector

11 FP_1 Front panel header

12 ATX1 24 pin main power connector

13 DIMM_P0_A0 Channel 1 slot 0

14 DIMM_P0_A1 Channel 2 slot 1

15 DIMM_P0_B0 Channel 3 slot 0

16 DIMM_P0_B1 Channel 4 slot 1

17 BAT1 Baery

18 PMBUS PMBus connector

19 SATA_DOM0 SATA DOM power cable connector

20 SATA0 SATA 3 6Gb/s connector

21 SATA1 SATA 3 6Gb/s connector

22 SATA_2_3 SATA 3 6Gb/s connectors

23 SATA_4_5 SATA 3 6Gb/s connectors

24 SATA_SGPIO SATA SGPIO header

25 COM1 Serial port cable connector

26 LED_BMC1 BMC ﬁrmware readiness LED

27 BP_1 HDD back plane board header

28 NVME_PH NVME connector

29 TPM TPM module connector

30 IPMB IPMB connector

No. Code Descripon

31 CLR_CMOS Clear CMOS jumper

1-2 Close: Normal operaon (Default seng)

2-3 Close: Clear CMOS data.

32 PCIE_1 PCI Express p1-x16 slot

33 ME_UPDATE ME update jumper

1-2 Close: Normal operaon (Default seng)

2-3 Close: ME update mode.

34 ME_RCVR ME recovry jumper

1-2 Close: Normal operaon. (Default seng)

2-3 Close: ME recovery mode.

35 S3_MASK S3 Power On Select jumper

1-2 Close: Stop an inial power on when BMC is not ready.

2-3 Close: Keep inial power on. (Default seng)

32 4 5 6 7 8 9

13141516

19 18

2021222325

262728

System Components/ 系统组件

No Descripon

1 HDD bays

2 System fan #9/#10 (FAN9/FAN10)

3 System fan #7/#8 (FAN7/FAN8)

4 System fan #5/#6 (FAN5/FAN6)

5 System fan #3/#4 (FAN3/FAN4)

6 System fan #1/#2 (FAN1/FAN2)

7 CPU and CPU heat sink

8 Memory slots

9 PCIe riser bracket

10 Power supply cage

CAUTION!

To connect system fan connector, follow the instrucon:

 Blue/Red cable connect to odd numbered connector.

 White/Amber cable connect to even numbered connector.

注意！

 蓝/红电缆连连接于单数风扇插座。

 白/橘电缆连连接于双数风扇插座。

Front Panel Header/ 前面板接头

No. Pin Deﬁne

1 Power LED+

3 No Pin

5 Power LED-

7 HDD LED+

9 HDD LED-

11 Power Buon

13 GND

15 Reset Buon+

17 GND

19 ID Switch+

21 ID Switch-

23 NMI Switch-

No. Pin Deﬁne

2 5V Standby

4 ID LED+

6 ID LED-

8 System Front Board LED+

10 System Status LED-

12 LAN1 Acve LED+

14 LAN1 Link LED-

16 SMBus Data

18 SMBus Clock

20 Case Open

22 LAN2 Acve LED

24 LAN2 Link LED-

2423

HDD Back Plane Board Header/ 硬盘驱动器底板接头

1 2

25 26

No. Pin Deﬁne

1 BP_SGP_CLK

3 BP_SGP_GLD

5 BP_SGP_DOUT

7 Key Pin

9 GND

11 BP_LED_G_N

13 BP_SGP_DIN

15 GND

17 GND

19 P_3V3_AUX

21 P_3V3_AUX

23 GND

25 BP_PRESENSE

No. Pin Deﬁne

2 No Connect

4 FAN_SGP_Gate

6 GND

8 Reset

10 BP_LED_A_N

12 GND

14 No Connect

16 SMB_BP_DATA

18 SMB_BP_CLK

20 BMC_ACK

22 BMC_REQ

24 Key Pin

26 GND

CAUTION!

Before you remove or install the system

cover:

Make sure the system is not turned on

or connected to AC power.

注意！

在卸下或安装系统机盖之前，请注意

下列事项：

确保系统未开启且未连接到交流电源。

System Cover/ 机箱盖

Fan Duct/ 风扇散热片

Memory Populaon Conﬁguraon/ 安装内存

Type

Ranks PerDIMM

and

Data Width

1600, 1866, 2133, 2400*

Speed (MT/s);

Slot Per Channel (SPC) and DIMM Per Channel (DPC)

1 Slot Per Channel

1DPC

2 Slot Per Channel

1DPC 2DPC

RDIMM

SRx4 ECC

SRx8 ECC

DRx8 ECC

DRx4 ECC

 仅Intel Xeon D-1541处理器支持DDR4-MHz内存。®

 只使用一个DIMM时，必须安装到内存插槽0。

 若安装顺序有误，系统将不能正常引导。

 Note: DDR4 2400MHz is only available on Intel Xeon® D-1541 processor.

 When only one DIMM is used, it must be populated in memory slot0 ﬁrst.

 System will not boot normally with incorrect populated sequence.

System Fan/ 系统风扇

CAUTION!

Before you remove or install the system fan:

 Make sure the system is not turned on or

connected to the AC power.

 Disconnect all necessary cable connecons.

Failure to observe these

warnings could result in personal injury or

damage to the equipment.

注意！

确保系统未开机且未连接到交流电源。

断开所有必要的线缆连接。若不遵循这些

警告，可能造成人员伤害或设备损坏。

CAUTION!

Read the following guidelines before you begin to install the Hard disk drive:

 Take note of the drive tray orientaon before sliding it out.

 The tray will not ﬁt back into the bay if inserted incorrectly.

 Make sure that the HDD is connected to the HDD connector on the backplane.

注意！

 在滑出驱动器托盘之前，注意其方向。

 托盘插入不当时，无法进入托槽。

 确保硬盘驱动器连接到底板上的硬盘驱动

器底板。

No Descripon

1 HDD#3

2 HDD#2

3 HDD#1

4 HDD#0

5 SGPIO header

6 Fan connector#13

7 Fan connector#14

8 Fan connector#11

9 Fan connector#12

10 ODD power connector

11 Fan connector#9

HDD Backplane Board Components

No Descripon

12 Fan connector#10

13 Fan connector#7

14 Fan connector#8

15 Fan connector#5

16 Fan connector#6

17 Fan connector#3

18 Fan connector#4

19 Fan connector#1

20 Fan connector#2

21 Fan connector#15

22 Fan connector#16

Hard Disk Drive and Back Plane Board/ 硬盘驱动器与硬盘驱动器底板

1234

6 7 8 9

11 12 13 14 15 16 17 18 19 20 21 22

System Front View System Rear View

No Descripon

1 ID buon w/LED

2 Power buon w/LED

3 HDD bays

No Descripon

1 Power supply fan

2 Power supply module cord socket

3 System Status LED

4 Power buon w/LED

5 ID switch buon w/LED

6 VGA port

7 USB 3.0 ports

8 10/100/1000 Server management LAN port

9 GbE LAN ports

10 SFP+ LAN ports

Front & Rear/ 系统前部与后部概览

Off

State Description

Yellow On 1Gbps data rate

Green On 100Mbps data rate

10Mbps data rate

State Description

Yellow On 1Gbps data rate

Green On 10 Gbps data rate

Speed LED Link/Acvity

LED

Speed LED Link/Acvity

LED

SFP+ LAN LED:

ID buon/LED:Power buon/LED:

Blue On System identifcation is active.

Off System identifcation is disabled.

State Description

Green On

Off

Description

System is powered on

System is powered off

State

1 2

1 2 3

45 6 7 8 9 10

PCI Express Card/PCI Express 扩展卡

注意！

在安装扩展卡前，请注意下列事项：

确保系统未开启且未连接到交流电源。

CAUTION!

Before you remove or install the PCI express card:

Make sure the system is not turned on or connected to AC power.

注意！

在替换或安装电源前，请注意下列事项：

确保系统未开启且未连接到交流电源

。

CAUTION!

Before you remove or install the power

supplies:

Make sure the system is not turned on or

connected to AC power.

Power Supply/ 电源

Rail Kit/ 导轨

Release

Lock out

⯮ⅎ庳⎽⇡

Release and de ch the inner member from the slideta

M4X6

Click

Aach the unit to the inner member

⯭Ⅼ彏擨

ᷱ

㜡⏗

Release

lock in

Insert the unit to complete the in nstallao

墬⅌㜡㞝

Brac tke

M6X13

M6-NUT

Fix the outer member/bracket assembly to the frame

⯭⣽彏㈿㞝擨⅌㜡㞝

Front Panel LED and Buons/ 前面板 LED 说明

7复位按钮按此按钮启动系统。

8复位按钮按此按钮启动不可遮罩中断功能。

2按下按钮启动系统识别功能。ID按钮

1系统处于开机状态。

系统处于ACPI S1状态（睡眠模式）。

系统未开机或处于ACPIS5状态（关机状态）。

系统处于ACPI S4状态（休眠模式）。

电源按钮和LED 绿色

绿色

恒亮

不亮

闪烁

无亮灯

不亮断开连接/待机无亮灯

5/6 恒亮

闪烁

系统和网络之间的链接

网络访问

绿色

LAN1/LAN2活动LED

6硬盘驱动器定位

硬盘驱动器访问

硬盘故障

无硬盘驱动器访问

绿色

橙色

绿色/橙色

不亮

亮

闪烁

无亮灯

硬盘驱动器LED

闪烁

编号名称颜色状态说明

3系统正常运行。

橙色

绿色

系统状态LED 恒亮

恒亮

不亮

闪烁

无亮灯

效能降低情形，可能为下列状况：

处理器问题

内存问题

严重情形，可能为下列状况：

电源模块故障

系统风扇故障

电源电压问题

系统温度/电压问题

非严重情形，可能为下列状况：

冗余电源模块故障

系统温度/电压问题

机箱侵入

系统未正常运行，可能为下列状况：

POST错误

NMI错误

处理器或终结器缺失

No. Name Color Status Description

7Reset Button Press the button to reset the system.

8NMI Button Press the button to generate an NMI.

2 Press the button to activate system identifcation.ID Button

1 System is powered on.

System is in ACPI S1 state (sleep mode).

System is not powered on or in ACPI S5 state (power off).

System is in ACPI S4 state (hibernate mode).

Power Button and LED Green

Green

Solid On

Off

Blink

N/A

4HDD locate

HDD access

HDD fault

No HDD access or no HDD fault.

Green

Amber

Green/Amber

Off

Blink

N/A

HDD Status LED

5/6 Link between system and network or no access.

Data transmission or receiving is occurring.

No data transmission or receiving is occurring.

Solid On

Off

Blink

Green

N/A

LAN1/2 Active/Link LEDs

状态

3 System is operating normally.

Degrade condition, may indicates:

CPU failure

DIMM killed

System Status LED

Green

Amber

Solid On

Critical condition, may indicates:

Power module failure

System fan failure

Power supply voltage issue

System temperature

Solid On

Non-critical condition, may indicates:

Redundant power module failure

Temperature and voltage issue

Chassis intrusion

System is not ready, may indicates:

POST error

NMI error

Processor or terminator missing

Blink

N/A N/A

Off

12345678

G150-B10 Quick Installaon Guide/G150-B10 快速安装说明

10/100/1000 LAN LED:

23456

PN:25ME0-G15000-CLS

Produkt Specifikationer

Mærke:	Gigabyte
Kategori:	Server
Model:	G150-B10

Har du brug for hjælp?

Hvis du har brug for hjælp til Gigabyte G150-B10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Server Gigabyte Manualer

Gigabyte TO24-JD0 Manual

15 December 2024

Gigabyte MS33-CP0 Manual

31 August 2024

Gigabyte R133-X11 Manual

31 August 2024

Gigabyte R183-S97 Manual

31 August 2024

Gigabyte R113-C10 Manual

31 August 2024

Gigabyte R183-SF0 Manual

31 August 2024

Gigabyte R133-X13 Manual

31 August 2024

Gigabyte R183-S96 Manual

31 August 2024

Gigabyte R123-X00 Manual

31 August 2024

Gigabyte R243-EG0 Manual

31 August 2024

Server Manualer

Nyeste Server Manualer

Luxman N50 Manual

1 Januar 2025

Advantech ADAM-4572-CE Manual

31 December 2025

Advantech EKI-1522I-CE Manual

31 December 2025

Advantech EKI-1521I-CE Manual

31 December 2025

Advantech EKI-1511-A Manual

31 December 2025

Advantech EKI-1528TI-VDC-CE Manual

31 December 2025

Advantech EKI-1526TI-VDC-CE Manual

31 December 2025

Advantech EKI-1528I-DR-AE Manual

31 December 2025

Advantech EKI-1522-CE Manual

31 December 2025

Advantech EKI-1526N-CE Manual

31 December 2025