Hikvision DS-PK-LRT(868MHz) Manual
Hikvision
Sikkerhed adgangskontrolsystem
DS-PK-LRT(868MHz)
Læs nedenfor 📖 manual på dansk for Hikvision DS-PK-LRT(868MHz) (2 sider) i kategorien Sikkerhed adgangskontrolsystem. Denne guide var nyttig for 24 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
Configure the address via DIP switch of the keypad before powering on the
system. The address should be in the range of 0 to 31. The address of each
keypad should be unique.
The binary value shown in the diagram is 00010, which means the decimal value
is 2. So the address of the keypad is 2.
One Beep
Two Beeps
Pressing keys/command med out or too long/Fault Prompt.
Valid command/Report uploaded.
Five Beeps Invalid command/Failed to upload the report in 60 s.
Rapid Beeps Zone alarm/keypad not registered.
Three Long Beeps and Two Short Beeps
Three Beeps
Keypad tampered.
Keypad registered.
a. Dimension
b. Wiring
Note: Hybrid control panel does not support Z1, GND, NO/NC, COM.
c. Install Keypad
(1) Gangbox Moung
(2) Wall Moung
It is required to insert the screw for tamper alarm.
Indicator
Key
Beeps
Wiring and Installaon
English
Diagram Reference
Product Information
Specification
Components and Beeps
1
3
Operaon Commands4
Address Sengs
2
1 2
3
Alarm Keypad
164.13 mm 30.96 mm
124.11 mm
a
b
c
Query
Set
Fault
Network
Armed/Disarmed
Alarm
Fire Panic One-Push
to Arm
Project Bypass Scoll Up
Scoll Down
Solid Green: No Configuraon
Flashing Green: In the Configuraon Status
Solid Green: All Enabled Channels Connected Normally
Flashing Red: Alarm Occurred/Tamper Alarm
Solid Blue: Armed Off: Disarmed
Off: No Alarm
Off: Part of or All Enabled Channels Connected Abnormally
Solid Orange: System Fault Off: No Fault
D- D+ 12V GND
D- D+ 12V GND
Control Panel
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the RE Direcve 2014/53/EU,
the EMC Direcve 2014/30/EU, the LVD Direcve
2014/35/EU, the RoHS Direcve 2011/65/EU.
2012/19/EU (WEEE direcve): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collecon points. For
more informaon see: www.recyclethis.info
The Input voltage should meet both the SELV (Safety
Extra Low Voltage) and the Limited Power Source
according to the IEC60950-1 standard. Please refer
to technical specificaons for detailed informaon.
BIN=00010
DEC=2
E.G
1 2 3 4 5
(1) GANGBOX MOUNTING
(2) WALL MOUNTING
Hybrid control panel does not support Z1, GND,
NO/NC, COM.
Scan the QR code a to get programming manual of Hybrid control panel.
HighbitLowbit
Slowly Connuous Beeps In the Entry/Exit delay status, the Delay zone armed,
or 2 min before auto arming/disarming starng.
Rapidly Connuous Beeps In the Entry/Exit delay status, the Delay zone
triggered, or 1 min before auto arming/disarming
starng.
UD15865B-B
©2020 Hangzhou Hikvision Digital Technology Co., Ltd. All
rights reserved.
About this Manual
The Manual includes instrucons for using and managing
the Product. Pictures, charts, images and all other
informaon hereinaer are for descripon and explanaon
only. The informaon contained in the Manual is subject to
change, without noce, due to firmware updates or other
reasons. Please find the latest version of this Manual at the
Hikvision website (hps://www.hikvision.com/).
Please use this Manual with the guidance and assistance of
professionals trained in supporng the Product.
Trademarks
and other Hikvision's trademarks and logos
are the properes of Hikvision in various jurisdicons. Other
trademarks and logos menoned are the properes of their
respecve owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS
MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH
ALL FAULTS AND ERRORS”. HIKVISION MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A
PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT
YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION,
WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING
NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN
CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR
LOSS.
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES
FOR INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE
ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY
LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK,
HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL
APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR
ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN
A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD
PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY,
INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND
OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR
ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR
PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE
DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL
WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY
NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN
SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND
THE APPLICABLE LAW, THE LATER PREVAILS.
3
Legal and Regulatory Information
M del DS-P -L DS-P -LRTo K K
Numeric key
Fu c keyn on
Display
K o N A oeyf b / Tw -way keyf bo
Tamper switch
RS-485 i terfacen
S u do n
Tag/ ard readi g / Supp rtC n N A o
P wer supplyo
P wero
c sumpon on
Temperature
Humidity
Dime sin on
L W )( × × H
Weight
12 keys: 0 t 9, , o * #
8 keys: Pr ject/ uery/Bypass/ e-push to Q On o
arm/Fire/Pa ic/Scr ll up/Scr ll d wn o o o n
L D screeC n
10 t 90% o %
-10 t 55 °C o °C
164 mm 124 mm 31 mm× ×
2 2 g7
1
1
buzzer
12 , 0.15 V A
1.8 W
1. The addional force shall be equal to three mes the
weight of the equipment but not less than 50N. The
equipment and its associated mounng means shall remain
secure during the installaon. Aer the installaon, the
equipment, including any associated mounng plate, shall not
be damaged.
2. Install the equipment according to the instrucons in this
manual.
3. To prevent injury, this equipment must be securely
aached to the wall in accordance with the installaon
instrucons.
INSTALLATION CAUTION
Produkt Specifikationer
Mærke: | Hikvision |
Kategori: | Sikkerhed adgangskontrolsystem |
Model: | DS-PK-LRT(868MHz) |
Har du brug for hjælp?
Hvis du har brug for hjælp til Hikvision DS-PK-LRT(868MHz) stil et spørgsmål nedenfor, og andre brugere vil svare dig
Sikkerhed adgangskontrolsystem Hikvision Manualer
12 Maj 2024
10 Maj 2024
27 April 2024
8 April 2024
10 Marts 2024
22 Februar 2024
6 Februar 2024
31 Januar 2024
28 Januar 2024
27 December 2023
Sikkerhed adgangskontrolsystem Manualer
- Sikkerhed adgangskontrolsystem Bosch
- Sikkerhed adgangskontrolsystem Abus
- Sikkerhed adgangskontrolsystem Burg Wächter
- Sikkerhed adgangskontrolsystem Optex
- Sikkerhed adgangskontrolsystem Honeywell
- Sikkerhed adgangskontrolsystem Viking
- Sikkerhed adgangskontrolsystem Techly
- Sikkerhed adgangskontrolsystem Marmitek
- Sikkerhed adgangskontrolsystem ASSA ABLOY
- Sikkerhed adgangskontrolsystem APC
- Sikkerhed adgangskontrolsystem Velleman
- Sikkerhed adgangskontrolsystem EQ3
- Sikkerhed adgangskontrolsystem ZKTeco
- Sikkerhed adgangskontrolsystem Steren
- Sikkerhed adgangskontrolsystem Safescan
- Sikkerhed adgangskontrolsystem Approx
- Sikkerhed adgangskontrolsystem Suprema
Nyeste Sikkerhed adgangskontrolsystem Manualer
22 Oktober 2024
22 Oktober 2024
22 Oktober 2024
22 Oktober 2024
2 Oktober 2024
2 Oktober 2024
1 Oktober 2024
5 August 2024
27 Juli 2024
12 Juli 2024