Hikvision DS-PM-WO2 Manual

Hikvision Ikke kategoriseret DS-PM-WO2

Læs nedenfor 📖 manual på dansk for Hikvision DS-PM-WO2 (6 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 34 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/6

RF Frequency 433MHz

RF Modula on FM

Transmisson Speed 10.0kbps

RF Transmisson Distance 800m (Open area)

Output Mode (NO/NC) 30 VDC/1A

Power Supply DC19V to DC15V

Inidcator

3 panel status indicators

8 internal relay status indicators

Tamper-proof

1 rear TAMPER bu om

1 front panel TAMPER buon

Internal Bu on Expander registra on

DIP Switch Enable/Disable indicator

Temperature

-10 to 55℃ ℃

Humidity 10% to 90%

Dimension (L × W × H) 160mm × 105mm ×28mm

Weight 165.0g

Installa on Wall-moun ng

Wireless Output Expander

Quick Start Guide

Product Informaon

Co., Ltd.

Any and all informaon, including, among others, wordings,

pictures, graphs are the properes of Hangzhou Hikvision

Digital Technology Co., Ltd. or its subsidiaries (hereinaer

referred to be “Hikvision”). This user manual (hereinaer

referred to be “the Manual”) cannot be reproduced,

changed, translated, or distributed, parally or wholly, by

any means, without the prior wrien permission of

Hikvision. Unless otherwise spulated, Hikvision does not

make any warranes, guarantees or representaons,

express or implied, regarding to the Manual.

About this Manual

This Manual is applicable to Control Panel

The Manual includes instrucons for using and managing

the product. Pictures, charts, images and all other

informaon hereinaer are for descripon and explanaon

only. The informaon contained in the Manual is subject to

change, without noce, due to ﬁrmware updates or other

reasons. Please ﬁnd the latest version in the company

website (hp://overseas.hikvision.com/en/).

Please use this user manual under the guidance of

professionals.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,

THE PRODUCT DESCRIBED, WITH ITS HARDWARE,

SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL

FAULTS AND ERRORS, AND HIKVISION MAKES NO

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT

LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,

FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGE-

MENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS

DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE

TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL,

OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,

DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS

INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN

CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF

HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET

ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR

OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBI-

LITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR

OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER

ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY

RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY

TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK

ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING

THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE

CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE

LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH

ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL

AND THE APPLICABLE LAW, THE LATER PREVAILS.

Trademarks Acknowledgement and other

Hikvision’s trademarks and logos are the properes of

Hikvision in various jurisdicons. Other trademarks and

logos menoned below are the properes of their

respecve owners.

English

Diagram Reference

①

②

③

④

⑤

⑥ ⑦

① ②

1Expander Wiring

Format the Expander:

Power the expander oﬀ. Hold the formang key and power the expander

on at the same me. Signal strength indicator ﬂashes three mes in red

when the formang is completed.

Select NO/NC Mode:

Turn the switch to the CNX terminal to set the mode as NC. Turn the switch

to the terminal to set the terminal as NO.

2Dimension

3Appearance

4Installaon

1. Check Signal Strength

1) Enter the signal checking mode by operang on the control panel. Wait for

the voice announcement to ﬁnish.

2) Hold the TAMPER buon for 2 seconds to trigger the tampering alarm,

and then observe the light of signal strength indicator.

Detector indicator turns green: Strong Signal.

Detector indicator turns red: Weak Signal.

2. Wire and route cables.

3. Install the rear panel: Secure the rear panel on the wall with 5 screws.

4. Fix the front panel on the rear panel by ghtening the set screw.

① Front Cover ③ Rear Cover

② ④ Screw Wall

5Register Expander

Power on the security control panel. Press the registraon key once and

add the expander accroding to the voice prompt.

Note: The distance between the security control panel and the expander

should be less than 50 cm.

Registering Expander via APP:

1.Log in to the APP Store and input “Hik-Connect” to search the mobile

client. Download and install Hik-Connect to your phone.

2.Aer installing, tap to run the client.

3.Power on the security control panel.

4.Log in the Hik-Connect and tap the icon“+” at the upper-right coner of the

Hik-Connect page to add the security control panel. You can scan the QR

code on the device rear panel or on the package box, or input the device

serial No. manually to add the device when the device is in the registraon

mode.

5.Aer adding the security control panel, tap the alarming status icon on

the right of the security control panel's name to enter the Paron page.

6.Tap the “+” icon on the Paron page to add the peripherals.

6DIP Switch

① Enbale the indicators Disable the indicators②

③ Power Indicator: Solid green aer power on

② Fault Indicator: Orange - Fault

① Signal Strength Indicator: Under the signal strength checking mode:

Green - Strong Signal Red - Weak Signal/

④ Register Buon / Formang Buon

⑤⑥ Terminals ⑦ DIP Switch

Speciﬁcaon

1 1

NO/

NC7

NO/

NC8 COM7COM8

NO/

NC2

NO/

NC1 COM2COM1VCCGND GND

NO/

NC5

NO/

NC6 COM5COM6

NO/

NC4

NO/

NC3 COM4COM3

Alarm Output

(Dry Contact)

Alarm Output

(Dry Contact)

CN7 CN8 C N9

CN6

CN5

CN10

CN12

CN11

Forma ng

S itchw

DIP S itchw

Tamper

S itchw

1 1

within 50cm

①

②

③④

105

160

Produkt Specifikationer

Mærke:	Hikvision
Kategori:	Ikke kategoriseret
Model:	DS-PM-WO2

Har du brug for hjælp?

Hvis du har brug for hjælp til Hikvision DS-PM-WO2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Hikvision Manualer

Hikvision DS-PI-T50 Manual

8 December 2024

Hikvision DS-PI-T50/FM Manual

8 December 2024

Hikvision DS-PI-D60/FM Manual

8 December 2024

Hikvision DS-PI-D60 Manual

8 December 2024

Hikvision DS-PI-D80/FM Manual

8 December 2024

Hikvision DS-PI-Q250 Manual

8 December 2024

Hikvision DS-PI-T100/FM Manual

8 December 2024

Hikvision DS-PI-T150/FM Manual

8 December 2024

Hikvision DVR-116G-K1 Manual

8 December 2024

Hikvision DS-1232ZJ-T Manual

30 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

EOTech EXPS3 Manual

26 December 2024

Schwinn 430 Manual

26 December 2024

Mount-It! MI-SB52 Manual

26 December 2024

Taga Harmony GTCS-606-6R SE Manual

26 December 2024

Taga Harmony TA-600multi Manual

26 December 2024

Taga Harmony TA-900multi Manual

26 December 2024

Taga Harmony TCW-100R v.3 Manual

26 December 2024

Taga Harmony TCW-180R Manual

26 December 2024

Taga Harmony TCW-380R Manual

26 December 2024

Taga Harmony TCW-600R v.2 Manual

26 December 2024