Honeywell 3800PDF Manual


Læs nedenfor 📖 manual på dansk for Honeywell 3800PDF (168 sider) i kategorien Stregkodelæser. Denne guide var nyttig for 9 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/168
3800/3900
Handheld Linear Imager
User’s Guide
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Class B Compliance Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio or television technician for help.
Caution: Any changes or modifications made to this device that are not
expressly approved by Hand Held Products, Inc. may void the user’s authority
to operate the equipment.
Note: To maintain compliance with FCC Rules and Regulations, cables
connected to this device must be shielded cables, in which the cable shield
wire(s) have been grounded (tied) to the connector shell.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as
described in the Radio Interference Regulations of the Canadian Department of
Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant
les limites applicables aux appareils numeriques de la classe B prescrites dans
le Reglement sur le brouillage radioelectrique edicte par le ministere des
Communications du Canada.
The CE mark on the product indicates that the system has been
tested to and conforms with the provisions noted within the 89/336/
EEC Electromagnetic Compatibility Directive and the 73/23/EEC
Low Voltage Directive.
For further information please contact:
Hand Held Products
Nijverheidsweg 9-13
Eindhoven, 5627 BT
The Netherlands
Hand Held Products shall not be liable for use of our product with equipment
(i.e., power supplies, personal computers, etc.) that is not CE marked and does
not comply with the Low Voltage Directive.
UL and cUL Statement
UL listed UL1950 and CSA 22.2 No.950. cUL listed UL1950 and CSA 22.2 No
950.
LED Safety Statement
This device has been tested in accordance with EN60825-1 LED safety, and has
been certified to be under the limits of a Class 1 LED device.
TÜV Statement
TÜV or GS marked to EN60950 and EN60825-1.
C-TIC Statement
Conforms to AS/NZS 3548. C-Tick number: N10410.
Patents
Please refer to the 3800/3900 packaging for patent information.
i
Chapter 1 - Getting Started
Typical Applications for the 3900 ........................................ 1-1
About This Manual ............................................................... 1-1
Unpacking the Scanner ......................................................... 1-2
3800 Scanner Identification.................................................. 1-3
3900 Scanner Identification.................................................. 1-3
Connecting the Scanner When Powered by Host
(Keyboard Wedge) ............................................................ 1-4
Mounting Information for the 3900 ..................................... 1-5
Specular Zone................................................................. 1-6
Plug and Play ........................................................................ 1-6
IBM 4683 Ports 5B, 9B, and 17 Interface ............................ 1-8
USB Interface ....................................................................... 1-9
OCIA Interface ................................................................... 1-11
NCR OCIA Short Format (8 Bit) Interface ........................ 1-11
NCR OCIA Long Format (9 Bit) Interface......................... 1-12
Nixdorf OCIA Interface...................................................... 1-12
Serial Wedge....................................................................... 1-12
Chapter 2 - Terminal Interfaces
Keyboard Wedge Connection............................................... 2-1
Terminal ID ......................................................................... 2-2
Supported Terminals............................................................. 2-3
Keyboard Country ................................................................ 2-5
Keyboard Style ..................................................................... 2-5
Keyboard Modifiers.............................................................. 2-6
Serial Port Connection.......................................................... 2-8
Baud Rate....................................................................... 2-9
RS-232 Word Length: Data Bits, Stop Bits, and Parity2-10
RS-232 Handshaking ................................................... 2-12
Wand Emulation Connection ....................................... 2-12
Wand Emulation Transmission Rate............................ 2-13
Wand Emulation Polarity............................................. 2-14
Wand Emulation Idle ................................................... 2-14
Table of Contents
ii
PDF417 Wand Emulation................................................... 2-15
Data Block Size............................................................ 2-15
Delay Between Blocks ................................................. 2-15
Overall Checksum........................................................ 2-16
Chapter 3 - Output
Scan Rate .............................................................................. 3-1
Beeper Volume ..................................................................... 3-1
Beeper Tone.......................................................................... 3-2
Scan Voting .......................................................................... 3-2
Reduce Quiet Zone ............................................................... 3-2
Reread Delay ........................................................................ 3-3
Good Read Delay.................................................................. 3-4
Trigger Mode........................................................................ 3-4
Chapter 4 - Data Editing
Prefix/Suffix Overview......................................................... 4-1
To Add a Prefix or Suffix: ............................................. 4-1
To Clear One or All Prefixes or Suffixes:...................... 4-2
To Add a Carriage Return Suffix to all Symbologies.... 4-3
Prefix Selections............................................................. 4-4
Suffix Selections ............................................................ 4-4
Symbology Chart.................................................................. 4-5
ASCII Conversion Chart (Code Page 1252)......................... 4-6
Function Code Transmit................................................. 4-7
Intercharacter, Interfunction, and Intermessage Delays ....... 4-7
Intercharacter Delay ....................................................... 4-7
User Specified Intercharacter Delay .............................. 4-8
Interfunction Delay ........................................................ 4-9
Intermessage Delay ........................................................ 4-9
iii
Chapter 5 - Data Formatting
Data Format Editor Introduction........................................... 5-1
To Add a Data Format.................................................... 5-1
Other Programming Selections ...................................... 5-2
Data Format Editor Commands...................................... 5-2
Data Format Editor......................................................... 5-4
Data Formatter................................................................ 5-5
Alternate Data Formats .................................................. 5-5
Chapter 6 - Secondary Interface
Secondary Code 39 Wand Emulation ................................... 6-1
Secondary RS-232 Connection ............................................. 6-1
Secondary Non Decoded Output Laser Emulation............... 6-2
Non Decoded Output Laser Emulation Transmission Rate.. 6-2
Non Decoded Output Laser Emulation Polarity ................... 6-2
Non Decoded Laser Emulation Idle...................................... 6-3
Disabling the Secondary Interface ........................................ 6-3
Secondary Trigger Mode ...................................................... 6-3
Chapter 7 - Symbologies
Introduction........................................................................... 7-1
All Symbologies.................................................................... 7-1
Message Length Description ................................................ 7-2
Codabar ................................................................................. 7-3
Start/Stop Characters ..................................................... 7-3
Check Character ............................................................. 7-4
Concatenation................................................................. 7-5
Codabar Message Length ............................................... 7-5
Code 39 ................................................................................. 7-6
Start/Stop Characters ..................................................... 7-6
Check Character ............................................................. 7-7
Code 39 Message Length ............................................... 7-7
Code 39 Append............................................................. 7-8
Base 32 ........................................................................... 7-8
Full ASCII ...................................................................... 7-9
iv
Interleaved 2 of 5 ................................................................ 7-10
Check Digit .................................................................. 7-10
Interleaved 2 of 5 Message Length .............................. 7-11
Strict Decoding............................................................. 7-11
Code 93............................................................................... 7-12
Code 93 Message Length ............................................. 7-12
Code 2 of 5.......................................................................... 7-13
Code 2 of 5 Message Length........................................ 7-13
IATA Code 2 of 5 ............................................................... 7-14
IATA Code 2 of 5 Message Length ............................. 7-14
Matrix 2 of 5 ....................................................................... 7-15
Matrix 2 of 5 Message Length ..................................... 7-15
Code 11............................................................................... 7-16
Check Digits Required ................................................. 7-16
Code 11 Message Length ............................................. 7-17
Code 128............................................................................. 7-18
<GS> Substitution........................................................ 7-18
Code 128 Message Length ........................................... 7-19
Telepen .............................................................................. 7-20
Telepen Output............................................................. 7-20
Telepen Message Length.............................................. 7-20
UPC A................................................................................. 7-21
Check Digit .................................................................. 7-21
Number System............................................................ 7-21
UPC A, continued ........................................................ 7-22
Addenda ....................................................................... 7-22
Addenda Required........................................................ 7-22
Addenda Separator ....................................................... 7-23
UPC Strict Decoding.................................................... 7-23
UPC E0 and UPC E1 .......................................................... 7-24
UPC E Expand ............................................................. 7-24
Check Digit .................................................................. 7-25
Number System............................................................ 7-25
Addenda ....................................................................... 7-26
Addenda Required........................................................ 7-26
Addenda Separator ....................................................... 7-27
v
EAN/JAN 13....................................................................... 7-28
Check Digit................................................................... 7-28
Addenda........................................................................ 7-29
Addenda Required........................................................ 7-29
Addenda Separator ....................................................... 7-30
ISBN Enable................................................................. 7-30
EAN/JAN 8......................................................................... 7-31
Check Digit................................................................... 7-31
Addenda........................................................................ 7-32
Addenda Required........................................................ 7-32
Addenda Separator ....................................................... 7-33
MSI ..................................................................................... 7-34
MSI, continued ............................................................. 7-34
Check Character ........................................................... 7-34
MSI Message Length.................................................... 7-35
Plessey................................................................................. 7-36
Plessey Message Length............................................... 7-36
RSS-14 ................................................................................ 7-37
RSS Limited........................................................................ 7-37
RSS Expanded .................................................................... 7-38
RSS Expanded Message Length................................... 7-38
China Post Code.................................................................. 7-39
China Post Message Length ......................................... 7-39
PDF417 ............................................................................... 7-40
PDF417 Message Length ............................................. 7-40
Show GLI Blocks ........................................................ 7-41
Scan Diagnostics .......................................................... 7-41
PDF Learn Mode .......................................................... 7-42
MicroPDF417 .................................................................... 7-43
MicroPDF417............................................................... 7-43
MicroPDF417 Message Length.................................... 7-43
EAN•UCC Composite Symbology .................................... 7-44
EAN•UCC Composite ........................................................ 7-44
Enable UPC/EAN Version.................................................. 7-44
EAN•UCC Composite Code Message Length ............. 7-45
vi
Chapter 8 - Cloning
Procedure .............................................................................. 8-1
Chapter 9 - Visual Menu
Visual Menu Introduction..................................................... 9-1
Temporary Visual Menu Configuration......................... 9-1
Installing Visual Menu from the Web............................ 9-1
Upgrading USB Firmware ............................................. 9-2
Chapter 10 - Interface Keys
Keyboard Function Relationships....................................... 10-1
Supported Interface Keys .................................................. 10-3
Chapter 11 - Utilities
To Add a Test Code I.D. Prefix to All Symbologies.......... 11-1
Show Software Revision..................................................... 11-1
Show Data Format .............................................................. 11-1
Specular Effect Reduction .................................................. 11-2
Chapter 12 - Serial Programming Commands
Conventions ........................................................................ 12-1
Menu Command Syntax ..................................................... 12-1
Query Commands......................................................... 12-2
Concatenation of Multiple Commands ........................ 12-2
Trigger Commands ............................................................. 12-4
Resetting the Factory Settings ............................................ 12-4
Menu Commands ............................................................... 12-5
PDF417 Wand Emulation ............................................ 12-7
Chapter 13 - Product Specifications
3800 Product Specifications ............................................... 13-1
3900 Product Specifications ............................................... 13-2
Standard Cable Pinouts....................................................... 13-3
vii
Chapter 14 - Maintenance
Repairs ................................................................................ 14-1
Maintenance........................................................................ 14-1
Replacing the Interface Cable ...................................... 14-2
Troubleshooting .................................................................. 14-2
Chapter 15 - Customer Support
Product Service and Repair................................................. 15-1
Online Product Service and Repair Assistance ............ 15-2
Technical Assistance........................................................... 15-2
Online Technical Assistance ........................................ 15-3
Limited Warranty ............................................................... 15-4
viii
3800/3900 User’s Guide 1 - 1
1
Getting Started
The 3800 is a high performance linear imaging scanner from Hand Held
Products. The 3800 marks a new performance level for handheld scanners.
Linear imaging technology is defined by a bright and sharply focused aiming line,
high resolution imaging, and fast reading speed. The 3800 is comfortable to
hold, easy to use, rugged, and excellent for all general scanning applications.
The 3900 is a fixed mount bar code scanner designed for retail kiosks,
manufacturing WIP tracking, document processing, or other OEM applications.
It is a complete decoded output scanner that is easy to integrate. It
communicates with PCs or host terminals via keyboard wedge or a serial RS-232
interface. The 3900 can be used internally or externally. The housing provides
protection from dust, dirt, and electrostatic discharge.
Typical Applications for the 3900
The 3900 is an ideal scanner
for retail kiosks. The bright
aiming line and large working
range make scanning easy for
untrained users.
The 3900 mounted in a stand
makes an efficient bar code
document reader; it takes up a
minimum of counter space and
reads and transmits data
quickly.
About This Manual
This User’s Guide provides installation and programming instructions for the
3800/3900. Product specifications, dimensions, warranty, and customer support
information are also included.
Hand Held Products bar code scanners are factory programmed for the most
common terminal and communications settings. If you need to change these
settings, programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
1 - 2 3800/3900 User’s Guide
Unpacking the Scanner
Open the carton. The shipping carton or container should contain:
Check to make sure everything you ordered is present.
Save the shipping container for later storage or shipping.
Check for damage during shipment. Report damage immediately to the
carrier who delivered the carton.
An 3800: or an 3900:
3800/3900 User’s Guide 1 - 3
3800 Scanner Identification
3900 Scanner Identification
www.handheld.com
Hand Held Products, Inc.
Made in USA
geprufte
S i c her heit
.
.
.
.
TUV
Rheinland
ProductSafety
E 153740
7D21
Input:
4.5-5.5VDC,
0-.3A
FOR HOME OR OFFICE USE
Tes ted to C omply With FC C S tandards
This Class B digital apparatus complies wit h Canadian
ICES-003. Cet appareil
numerique de la
Classe B est conforme a la
norme NMB-003 du Canada.
N10410
S e e m anua l f or
P a te n t d e ta ils .
Input:
4.5-5.5 VDC, 0-.3A
S ee m a nu al for
P aten tdetails .
Made in USA
geprufte
Sicherheit
.
.
.
.
TUV
Rheinland
Product Safety
E 153740
7D21
Teste d toCo mply WithFCC St an dards
FOR HOME OR OFFICE USE
Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada.
This C lass B d igi tal apparatu s c omp lie s w ith C ana dian ICE S-0 03.
N10410
Hand Held Products, Inc.
ww w.handheld.com
3900 Scanner
Bottom View
Input:
4.5-5.5 VDC, 0-.3A
S ee m a nu al f or
P a tent deta ils .
Made in USA
gep r u ft e
Si cher h e it
.
.
.
.
TUV
Rheinland
Product Safety
E 153740
7D21
Tes ted to C omply With FC C S tandards
FOR HOME OR OFFICE USE
Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada.
This Class B digital apparatus complies with Canadian ICES-003.
N 10410
Hand Held Products, Inc.
www.handheld.com
1 - 4 3800/3900 User’s Guide
Connecting the Scanner When Powered by Host
(Keyboard Wedge)
A scanner can be connected between the keyboard and PC as a “keyboard
wedge,” plugged into the serial port, or connected to a portable data terminal in
wand emulation or non decoded output mode. The following is an example of a
keyboard wedge connection:
1. Turn off power to the terminal/computer.
2. Disconnect the keyboard cable from the
back of the terminal/computer.
3. Connect the appropriate
interface cable to the
scanner and to the terminal/
computer.
4. Turn the terminal/computer
power back on. The scanner will beep twice.
5. Verify the scanner operation by scanning a bar code from the back cover of
this manual. The scanner will beep once.
Disconnect
Disconnect
Disconnect
Disconnect
Disconnect
12
3
3800/3900 User’s Guide 1 - 5
Mounting Information for the 3900
Aperture plane
1.52
1.52
B
B
B
BB
.8 Optical center is ± 2" from horizontal.
(Angle begins at aperture plane.)
2˚ Ref typ
4.64
2.67 1.52 Ref
2.99
47.5˚
.89
.04
.700
.700
M4 Inserts typ 3
Thread depth
4.7 mm (.185")
Cable Exit
1.3
.65
2.5
(13 mil and 15 mil)
3.5
(5 mil and 7.5 mil)
4.1
5
6
7
8.5
9.5
3 mil
5 mil
7.5 mil 13 mil
15 mil
23˚ typ
4.9
4.2
3
1.9
TYPICAL PERFORMANCE ON HIGH QUALITY SYMBOLS.
Note: Measurements are in inches.
1 - 6 3800/3900 User’s Guide
Mounting Information, continued
Specular Zone
The 3900 must be mounted at a 5 degree, or greater, angle to the bar code in
order to scan properly:
The scanner is now connected and ready to communicate with your terminal/PC.
You must program the scanner for your interface before bar code data can be
transmitted to your terminal/PC. If you are using the scanner as a keyboard
wedge, turn to page 2-1. If the scanner is connected via a serial port, turn to
page 2-8. If this is a wand emulation application, turn to page 2-15, and for a non
decoded output connection, turn to page 6-2.
Plug and Play
Plug and Play bar codes provide instant scanner set up for commonly used
interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have the
interface in effect.
The most common interface is Keyboard Wedge. The following Keyboard
Wedge bar code also programs a carriage return (CR) suffix.
Keyboard Wedge Interface for IBM PC
AT and Compatibles
3800/3900 User’s Guide 1 - 7
The following Plug and Play bar code for IBM XT and Compatibles also
programs a carriage return (CR) suffix.
The following Plug and Play bar code for IBM PS-2 and Compatibles also
programs a carriage return (CR) suffix.
Use Non Decoded Output Laser Emulation when connecting to a secondary
terminal with integral decoding. This also sets the transmission rate to 36 scans
per second and the polarity to white high.
For most laptops, scanning the Laptop Direct Connect bar code allows
operation of the integral keyboard. The following Laptop Direct Connect bar
code also programs a carriage return (CR) suffix.
The RS-232 Interface bar code is used when connecting to the serial port of a
PC or terminal. The following RS-232 Interface bar code adds a suffix of a CR
and LF, and also programs the parameters:
Option Setting
Baud Rate 9600 bps
Parity Even
IBM XT and Compatibles
IBM PS-2 and Compatibles
Non Decoded Output
Laser Emulation
Laptop Direct Connect
1 - 8 3800/3900 User’s Guide
In Wand Emulation mode, the scanner decodes the bar code then sends data in
the same format as a wand scanner. The Same Code format transmits UPC,
EAN, Code 128 and Interleaved 2 of 5 bar codes without any changes, but
converts all other symbologies to Code 39.
The following Wand Emulation bar code sets the interface to Wand Emulation
mode and translates bar code data as Code 39 symbology. It also programs the
Transmission Rate to 25 inches per second, and Output Polarity to black high.
Note: For the 3800PDF model: When the 3800PDF interface is set to wand
emulation, all PDF417 bar code data is transmitted as Code 128. Data
from other symbologies follow the rules described above.
IBM 4683 Ports 5B, 9B, and 17 Interface
Note: The following Retail “Plug and Play” codes are for use with the 3800XX-
11 and 3800XX-11E models only.
Scan one of the following “Plug and Play” codes to program the 3800 for IBM
4683 Port 5B, 9B, or 17.
Data Format 7 data bits, parity bit, 1 stop bit (8 bit data)
Option Setting
RS-232 Interface
Wand Emulation Same Code
Wand Emulation (Code 39 Format)
3800/3900 User’s Guide 1 - 9
Note: After scanning one of these codes, you must re-boot the cash register.
Each bar code above also programs the following suffixes for each symbology:
USB Interface
Note: The following USB “Plug and Play” codes (IBM SurePOS handheld and
tabletop scanners) are for use with the 3800XX-15 models only.
Scan one of the following “Plug and Play” codes to program the 3800 for IBM
SurePos (USB Handheld scanner) or IBM SurePos (USB Tabletop scanner).
Symbology Suffix
EAN 8 0C
EAN 13 16
UPC A 0D
UPC E 0A
Code 39 00 0A 0B
Interleaved 2 of 5 00 0D 0B
Code 128 00 18 0B
IBM 4683 Port 5B Interface
IBM 4683 Port 9B HHBCR-1 Interface
IBM 4683 Port 9B HHBCR-2 Interface
IBM 4683 Port 17 Interface
1 - 10 3800/3900 User’s Guide
Note: After scanning one of these codes, you must re-boot the cash register.
Each bar code above also programs the following suffixes for each symbology:
Scan one of the following codes to program the 3800 for USB PC Keyboard or
USB Macintosh Keyboard.
Scan the following code to program the 3800 for USB HID bar code scanners.
Symbology Suffix
EAN 8 0C
EAN 13 16
UPC A 0D
UPC E 0A
Code 39 00 0A 0B
Interleaved 2 of 5 00 0D 0B
Code 128 00 18 0B
IBM SurePos (USB Handheld Scanner) Interface
IBM SurePos (USB Tabletop Scanner) Interface
USB Keyboard (PC)
USB Keyboard (Mac)
USB HID Bar Code Scanner
3800/3900 User’s Guide 1 - 11
OCIA Interface
Note: The OCIA interfaces are only available on the 3800XX-11 and 3800XX-
11E models.
Scan one of the following “Plug and Play” codes to program the 3800 for Generic
OCIA, NCR OCIA Short Format (8 bit), NCR OCIA Long Format (9 bit), and
Nixdorf OCIA.
Note: After scanning one of these codes, you must re-boot the cash register.
The Generic OCIA bar code also programs the following prefixes for each
symbology:
NCR OCIA Short Format (8 Bit) Interface
The NCR OCIA Short Format (8 Bit) bar code also programs the following
prefixes for each symbology:
Symbology Prefix
EAN 8 06 06
EAN 13 06
UPC A 01
UPC E 05
Symbology Prefix
EAN 8 0F 0F
EAN 13 0F
UPC A 0A
UPC E 0E
Generic OCIA Interface
NCR OCIA Short Format (8 Bit) Interface
1 - 12 3800/3900 User’s Guide
NCR OCIA Long Format (9 Bit) Interface
The NCR OCIA Long Format (9 Bit) bar code also programs the following
prefixes for each symbology:
Nixdorf OCIA Interface
The Nixdorf OCIA bar code also programs the following prefixes for each
symbology:
Serial Wedge
The 3800/3900 uses true and TTL signal levels to wedge into an RS-232 serial
network. Use 3800/3900 serial wedge cables only to prevent damage to the
scanner. Refer to the serial interface programming (pages 2-8 to 2-12) to set the
baud rate and communications protocol.
Symbology Prefix
EAN 8 46 46
EAN 13 46
UPC A 41
UPC E 45
Code 39 42 31
Interleaved 2 of 5 42 32
Code 128 42 33
Symbology Prefix
EAN/UPC with Addenda 44 4B
Code 39 44 49
Interleaved 2 of 5 44 48
2 of 5 44 47
Code 128 44 4A
NCR OCIA Long Format (9 Bit) Interface
Nixdorf OCIA Interface
3800/3900 User’s Guide 1 - 13
To set up the serial wedge terminal ID, find the terminal ID in the Supported
Terminal Chart and follow the instructions on page 2-2. Set the port to which you
want the scanned data to transmit. Port 1 corresponds to P1 on the output cable
and Port 2 corresponds to P2 on the output cable. Choosing Both sends
scanned data to P1 and P2. Default = P1.
* P1
P2
Both P1 and P2
1 - 14 3800/3900 User’s Guide
3800/3900 User’s Guide 2 - 1
2
Terminal Interfaces
Keyboard Wedge Connection
3800/3900 scanners are factory programmed for a keyboard wedge interface to
an IBM PC AT with a USA keyboard. If this is your interface and you do not need
to modify the settings, skip to Chapter 3 - Output.
If you programmed the scanner for a different terminal interface and/or you want
to change to an IBM PC AT and Compatibles Keyboard Wedge interface, scan
the bar code below.
IBM PC AT and Compatibles
with CR suffix
2 - 2 3800/3900 User’s Guide
Terminal ID
If your interface is not a standard PC AT, refer to "Supported Terminals" on page
2-3 through page 2-4, and locate the Terminal ID number for your PC. Scan the
Terminal ID bar code below, then scan the numeric bar code(s) on the inside
back cover of this manual to program the scanner for your terminal ID. Scan
Save to save your selection.
For example, an IBM AT terminal has a Terminal ID of 003. You would scan the
Terminal ID bar code, then 0, 0, 3 from the inside back cover, then Save. If you
make an error while scanning the digits (before scanning Save), scan the
Discard code on the back cover, scan the Terminal ID bar code, scan the digits,
and the Save code again.
Note: After scanning one of these codes, you must power cycle your computer.
Terminal ID
Save
3800/3900 User’s Guide 2 - 3
Supported Terminals
Terminal Model(s) Terminal ID
Apple Mac Mac Classic, SE SE30, II (All) 049 **
Apple Mac Powerbook 5300 Series (Portable PC) 049 **
DEC VT510, 520, 525 (PC style) 005
DEC VT510, 520, 525 (DEC style
LK411)
104
Esprit 200, 400 005
Heath Zenith PC, AT 090
HP Vectra 003
HP Vectra ES 023
IBM XT 001
IBM PS/2 25, 30, 77DX2 002
IBM AT, PS/2 30–286, 50, 55SX, 60,
70, 70–061, 70–121, 80
003 *
IBM 102 key 3151, 3161, 3162, 3163, 3191,
3192, 3194, 3196, 3197, 3471,
3472, 3476, 3477
006
IBM 122 key 3191, 3192, 3471, 3472 007
IBM 122 key 3196, 3197, 3476, 3477, 3486,
3482, 3488
008
IBM 122 key 3180 024
IBM 122 key 3180 data entry keyboard 114
IBM DOS/V 106 key PC & Workstation 102
IBM SurePOS USB Handheld Scanner 128****
IBM SurePOS USB Tabletop Scanner 129****
IBM Thinkpad 360 CSE, 340, 750 097
IBM Thinkpad 106
IBM Thinkpad 365, 755CV 003
I/O 122 key 2676D, 2677C, 2677D 008
ITT 9271 007
Lee Data IIS 007
NEC 98XX Series 103
Olivetti M19, M200 001
Olivetti M240, M250, M290, M380,
P500
003
RS-232 True 000 ***
RS-232 TTL 000
Serial Wedge 050
Silicon Graphics Indy, Indigoll 005
2 - 4 3800/3900 User’s Guide
Telex 88 key
078, 078A, 79, 80, 191, 196,
1191,1192, 1471, 1472, 1476,
1477, 1483
025
Telex 88 key Data Entry Keyboard 112
Telex 102 key
078, 078A, 79, 80, 191, 196,
1191,1192, 1471, 1472, 1476,
1477, 1483
045
Telex 122 key
078, 078A, 79, 80, 191, 196,
1191,1192, 1471, 1472, 1476,
1477, 1482, 1483
046
USB converter 124
USB PC Keyboard 124 *****
USB Mac Keyboard 125
Wand Emulation 061
*
Default for -11, -12 models
** Applies to -12 models only
*** Default for -13 model (applies to -13 models only)
**** Applies to -15 model only. Because special suffixes are required
by the IBM SurePOS terminal, it is best to use the Plug and Play
bar codes on page 1-10 to program these interfaces, rather than
scanning the terminal ID listed in this table.
***** Default for -14, -15 models
Supported Terminals (Continued)
Terminal Model(s) Terminal ID
2 - 6 3800/3900 User’s Guide
Shift Lock
is used when you normally have the Shift Lock key on (not common
to U.S. keyboards).
Automatic Caps Lock
is used if you change the Caps Lock key on and off. The
software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only).
This selection can only be used with systems that have an LED which notes the
Caps Lock status.
Emulate External Keyboard
should be scanned if you do not have an external
keyboard (IBM AT or equivalent). To connect the scanner to a laptop, it may be
necessary to use the Automatic Direct Connect selection on in page 2-7
conjunction with the bar code below.
Note: After scanning the Emulate External Keyboard bar code, you must power
cycle your computer.
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo
Mode.
Control + ASCII Mode On:
The scanner sends key combinations for ASCII
control characters for values 00-1F. Refer to page 10-1 for CTRL+ ASCII
Values. Default = Off
Shift Lock
Automatic Caps Lock
Emulate External Keyboard
Control + ASCII Mode On
* Control + ASCII Mode Off


Produkt Specifikationer

Mærke: Honeywell
Kategori: Stregkodelæser
Model: 3800PDF

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell 3800PDF stil et spørgsmål nedenfor, og andre brugere vil svare dig




Stregkodelæser Honeywell Manualer

Stregkodelæser Manualer

Nyeste Stregkodelæser Manualer

Cognex

Cognex DataMan 50 Manual

26 Februar 2025
Unitech

Unitech MS852N Manual

23 Februar 2025
Unitech

Unitech MS926 Manual

23 Februar 2025
Unitech

Unitech MS242 Manual

23 Februar 2025
Unitech

Unitech MS588 Manual

23 Februar 2025
Unitech

Unitech MS851 Manual

23 Februar 2025
Unitech

Unitech MS840P Manual

21 Februar 2025
Unitech

Unitech MS838B Manual

20 Februar 2025
Unitech

Unitech MS339 Manual

20 Februar 2025
Unitech

Unitech MS842DPM Manual

20 Februar 2025