Honeywell Horizon 7625 Manual

Honeywell Stregkodelæser Horizon 7625

Læs nedenfor 📖 manual på dansk for Honeywell Horizon 7625 (84 sider) i kategorien Stregkodelæser. Denne guide var nyttig for 34 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/84

METROLOGIC INSTRUMENTS, INC.

MS7600 Horizon®Series

Installation and User’s Guide

iii

T CABLE OF ONTENTS

Introduction........................................................................................................... 1

Scanner and Accessories..................................................................................... 2

Before Installing Your MS7600............................................................................. 4

Mounting the MS7600 Series

Option A: Shelf Support .................................................................................... 5

Option B: Free Hanging Support....................................................................... 6

Option C: Trim Ring .......................................................................................... 7

Installation

For Keyboard Wedge Interface......................................................................... 8

For Stand-Alone Keyboard Interface ................................................................ 9

For USB Interface ........................................................................................... 10

For RS232 or Light Pen Interfaces ................................................................. 12

For IBM 46xx Interface ................................................................................... 14

For OCIA Interface.......................................................................................... 15

Of a Secondary Scanner ................................................................................ 16

Scanner Parts..................................................................................................... 19

Maintenance....................................................................................................... 20

EAS Deactivation Antenna ................................................................................. 20

Scanner Labels .................................................................................................. 21

Audible Indicators............................................................................................... 22

Visual Indicators ................................................................................................. 23

Failure Modes..................................................................................................... 24

Changing the Beeper Tone & Volume ................................................................ 25

Power Save Modes and IR Detection................................................................. 26

Scan Volume Specifications ............................................................................... 28

Depth of Field by Minimum Bar Code Element Width ........................................ 29

Troubleshooting Guide ....................................................................................... 30

Design Specifications ......................................................................................... 35

RS232 Demonstration Program ......................................................................... 37

Applications and Protocols ................................................................................. 38

Default Settings .................................................................................................. 39

Scanner and Cable Terminations ....................................................................... 45

Limited Warranty ................................................................................................ 49

Notices ............................................................................................................... 50

Patents ............................................................................................................... 52

Index................................................................................................................... 53

MOUNTING THE MS7600 SERIES

OPTION B: Free Hanging Support

Figure 8: Package Flow (right)

Figure 9: Specifications for free hanging support.

Figure 10: Installation Tabs

Figure 19: RS232/IBM, Interface

I INSTALLATION FOR IBM 46XX NTERFACE

1. Turn off the host system.

2. Connect the MVC cable to the

1st jack down from the top of

the MS7600.

3. Connect the other end of the

MVC cable to the host.

Before continuing verify that the

MVC cable is connected to the

appropriate interface jack on the

scanner. An incorrect cable

connection can cause

communication problems or

potential damage to the scanner.

Manufacturers Note:

Plugging the scanner into the

serial port of the PC does not

guarantee that scanned

information will appear at the PC.

A software driver and correct

configuration setting are also

required for proper

communication to occur.

4. Turn on the host system.

5. Scan the Load 46xx IBM Defaults

bar code to configure the

MS7600 for IBM 46xx

communication.

For additional communication options for IBM interfaces refer to the MetroSelect

Programming Guide (MLPN 00-02407).

Caution:

To maintain compliance with applicable standards, all circuits connected to the scanner must meet the

requirements for SELV (Safety Extra Low Voltage) according to EN 60950.

To maintain compliance with standard CSA C22.2 No. 60950-00/UL 60950 and norm EN 60950, the power

source should meet applicable performance requirements for a limited power source.

³999995

Load 46xx IBM Defaults

V IISUAL NDICATORS

There is a red LED and amber LED on

the front of the MS7600. When the scanner is

on, the flashing or constant illumination of the

LEDs indicates the status of the current scan

and the scanner.

Figure 24: LEDs

No Red or Amber LED

The LEDs will not be illuminated if the scanner is

not receiving power from the host or transformer.

Steady Amber

When the laser is active, the amber LED is

illuminated. The amber LED will remain

illuminated until the laser is deactivated.

Steady Amber and Single Red Flash

When the scanner successfully reads a bar code,

the red LED will flash and the scanner will beep

once. If the red LED does not flash or the

scanner does not beep once, then the bar code

has not been successfully read.

Steady Amber and Steady Red

After a successful scan, the scanner transmits

the data to the host device. Some

communication modes require that the host

inform the scanner when data is ready to be

received. If the host is not ready to accept the

information, the scanner’s red LED will remain on

until the data can be transmitted.

Flashing Amber then Flashing Red

This indicates the scanner is in program mode. A

razzberry tone indicates that an invalid bar code

has been scanned in this mode.

If the unit is in sleep mode, each LED will flash

once every 15 seconds.

Steady Red, Amber off

This indicates the scanner may be waiting for

communication from the host.

S V SCAN OLUME PECIFICATIONS

(BASED ON AR 100% UPC B CODES)

Figure 28: Scan Volume in Plane Perpendicular to Flow

Figure 29: Scan Volume in Plane Parallel to Flow

Specifications subject to change without notice.

T G )ROUBLESHOOTING UIDE (CONTINUED

SYMPTOMS POSSIBLE CAUSE(S) SOLUTION

Scanning a particular

symbology that is not

enabled.

UPC/EAN, Code 39, interleaved

2 of 5, Code 93, Code 128 and

Codabar are enabled by default.

Verify that the type of bar code

being read has been selected.

The unit powers

up, but does

not scan and/or

beep.

The scanner has been

programmed for a

character length lock,

or a minimum length

and bar code being

scanned does not

satisfy the

programmed criteria.

Verify that the bar code that is

being scanned falls into the

criteria.

(Typical of Non-UPC/EAN

codes. The scanner defaults to

a minimum of 4 character bar

code.)

The unit scans

a bar code, but

locks up after

the first scan

(red LED stays

on).

The scanner is

configured to support

some form of host

handshaking but is not

receiving the signal.

If the scanner is setup to support

ACK/NAK, RTS/CTS,

XON/XOFF or D/E, verify that

the host cable and host are

supporting the handshaking

properly.

The unit scans,

but the data

transmitted to

the host is

incorrect.

The scanner’s data

format does not match

the host system

requirements.

Verify that the scanner’s data

format matches that required by

the host. Make sure that the

scanner is connected to the

proper host port.

The print quality of the

bar code is suspect.

Also check character

length lock.

Scanner beeps

at some bar

codes and NOT

for others of the

same bar code

symbology. The aspect ratio of the

bar code is out of

tolerance.

Check print mode. The type of

printer could be the problem.

Change print settings. For

example change to econo mode

or high speed.

Produkt Specifikationer

Mærke:	Honeywell
Kategori:	Stregkodelæser
Model:	Horizon 7625
Vægt:	2900 g
Produktfarve:	Grå
Opbevaringstemperatur (T-T):	-40 - 60 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Strømforbrug (standby):	0.83 W
Driftstemperatur (T-T):	0 - 40 °C
Husmateriale:	Rustfrit stål
Dimensioner (BxDxH):	229 x 193 x 88 mm
Certificering:	FCC, ICES, EN, IEC
Indgangsspænding:	5 V
Standard grænseflader:	USB,RS-232,PS/2
Strømforbrug:	500 mA
Lyskilde:	VLD 650 +/- 10nm
Strømforbrug (aktiv):	2.6 W
Pitch læsningsvinkel:	-60 - 60 °
Yaw læsningsvinkel:	-60 - 60 °
Afkodningsstandarder:	1D, GS1