Hotpoint H8I HP42 L UK Manual

Hotpoint Opvaskemaskine H8I HP42 L UK

Læs nedenfor 📖 manual på dansk for Hotpoint H8I HP42 L UK (8 sider) i kategorien Opvaskemaskine. Denne guide var nyttig for 2 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/8
EN
1
Daily Reference Guide
THANK YOU FOR BUYING AHOTPOINT PRODUCT.
In order to receive amore complete assistance, please
register your appliance on: www.hotpoint.eu/register
1. ON-OFF/Reset button with indicator light
2. PREVIOUS program button
3. NEXT program button
4. FAVOURITE program button with indicator light
5. Salt reservoir empty indicator light
6. Rinse Aid reservoir empty indicator light
7. DESCALE indicator light
8. Closed Water Tap indicator light
9. Display
10. Program number remaining time and indicator
11. 3D Zone Wash button with indicator lightoption
FIRST TIME USE
1 2 3 4 11 12 13 14 155 6 7 8 9 10
12. Half Load option button with indicator light/ - 3 sec. pressSettings
13. Extra Dry option button with indicator light
14. Delay option button with indicator light
15. START/Pause button with indicator light
SETTING MENU
1. Switch on the appliance by pressing the button.ON-OFF
2. Hold the Settings (Half Load ) button for 3 seconds, until you hear
abeep and the display shows „SEt”.
3. After one second therst available setting (letter „h”) will be displayed.
4. Press PREVIOUS / NEXT to scroll through the list of available settings
(see table below), then press START/Pause to view and change the
value of the currently selected setting.
5. Press PREVIOUS /NEXT to change the value, then press START/Pause
to save the new value and return to the main menu.
6. To change another setting, repeat points 4 and 5.
7. Press or wait 30 seconds to exit the menu.ON-OFF
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
The salt reservoir is located in the lower part of the dishwasher (under the
lower rack on the left side).
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
• Salt must be lled when the SALT REFILL indicator light on the con-
trol panel is lit.1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 0,5 kg); it is not un-
usual for alittle water to leak out.
3. Only the rst time you do this: ll the salt reservoir
with water.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Run aprogram every time as soon as you completed relling the salt
reservoir to avoid corrosion.
Setting the water hardness
To allow the water softener to work in aperfect way, it is essential that the water
hardness setting is based on the actual water hardness in your house. This infor-
mation can be obtained from your local water supplier. The factory setting is “3”.
See „WATER HARDNESS TABLE”.
To change, follow instructions in section “SETTING MENU”.
Only use salt that has been specically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator
light switches o.
If the salt container is not lled, the water softener and the heating
element may be damaged as aresult of limescale accumulation.
Use of salt is recommended with any type of dishwasher detergent.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing
scale buildup on the heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
the salt container when empty. The frequency of regeneration depends
on the water hardness level setting - regeneration takes place once per 4-6
Eco cycles with the water hardness level set to 3. The regeneration process
occurs at the beginning of the cycle with additional fresh water.
• Single regeneration consumes ~3L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A
lled when the RINSE AID REFILL indicator light in the control panel is lit.
1. Open the dispenser B by
pressing and pulling up the
tab on the lid.
2. Pour in the rinse aid (max.110
ml), making sure it does not
overow from the dispenser.
If this happens, clean the spill
immediately with adry cloth.
3. Press the lid down until you hear aclick to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the dosage of rinse aid
If you are not completely satised with the drying results, you can adjust
the quantity of rinse aid used.
To change, follow the instructions in the section “SETTING MENU”.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
Amaximum of levels can be set according to the dishwasher model. 6
• If you see bluish streaks on the dishes, set alow number (0-3).
• If there are drops of water or limescale marks on the dishes, set
amid-range number (4-5).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device Introduce the C.
detergent into the dry dispenser only. Place the amount of detergent for D
pre-washing directly inside the tub.
1. When measuring out the detergent refer to the
mentioned earlier information to add the proper
quantity. Inside the dispenser , there are indicaD-
tions to help the detergent dosing.
2. Remove detergent residues from the edges of the
dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling
it up until the closing device is secured in place.
The detergent dispenser automatically opens up at the right time accord-
ing to the program.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
A
B
D
C
LETTER SETTING VALUES
(Default - )in bold
Water Hardness Level
(see “SETTING THE WATER HARDNESS”
and “WATER HARDNESS TABLE”) 1 | 2 | | 4 | 53
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF RINSE AID”) 0 | 1 | 2 | 3 | 4 | 5
ActiveDry (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Light on the oor (see “OPTIONS AND FUNCTIONS”)
“1” = On, “0” = O 1 | 0
Sound
“1” = On, “0” = O 1 | 0
Factory Settings
Press START/Pause to restore to the factory
default all the values of the settings included
in the settings menu.
-
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
°Clark
English degrees
1 (soft) 0 - 6 0 - 10 0 - 7
2 (medium) 7 - 11 11 - 20 8 - 14
3 (average) 12 - 16 21 - 29 15 - 20
4 (hard) 17 - 34 30 - 60 21 - 42
5 (very hard) 35 - 50 61 - 90 43 - 62
CONTROL PANEL
Before using the appliance carefully read Safety
and Installation Instructions. More information about your product
available on website: docs.whirlpool.eu
After installation, please remember to remove all transport protection
parts from the dishwasher.

Produkt Specifikationer

Mærke: Hotpoint
Kategori: Opvaskemaskine
Model: H8I HP42 L UK

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint H8I HP42 L UK stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine Hotpoint Manualer

Hotpoint

Hotpoint LSTA+ 216 A/HA Manual

13 Oktober 2024
Hotpoint

Hotpoint LSB 5B019 X Aquarius Manual

10 Oktober 2024
Hotpoint

Hotpoint LTF 8B116 EU Manual

3 Oktober 2024
Hotpoint

Hotpoint FDFEX11011P Manual

12 September 2024
Hotpoint

Hotpoint FDFEX 11011 K Extra Manual

5 September 2024
Hotpoint

Hotpoint H0I D534A S Manual

4 September 2024
Hotpoint

Hotpoint H8I HP42 L Manual

2 September 2024
Hotpoint

Hotpoint HI9E 2B19 Manual

2 September 2024
Hotpoint

Hotpoint H2I HD526 A Manual

2 September 2024
Hotpoint

Hotpoint HFC 3C26 W UK Manual

2 September 2024

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Siemens

Siemens SN45M283SK Manual

3 December 2024
Bosch

Bosch SGS44E72EU Manual

29 November 2024
Samsung

Samsung DW60M9550BB Manual

26 November 2024
Bosch

Bosch SMS63M18AU Manual

26 November 2024
Kogan

Kogan KABNCHTPDWA Manual

26 November 2024
Siemens

Siemens SX64M080EU Manual

26 November 2024
Bosch

Bosch SGU53E15AU Manual

25 November 2024
Samsung

Samsung DW60M5044FS Manual

24 November 2024
Samsung

Samsung DW60DG550B00 Manual

24 November 2024
Samsung

Samsung DW60DG540FSR Manual

24 November 2024