Hotpoint HTS15BBMLCC Manual

Hotpoint Køleskab HTS15BBMLCC

Læs nedenfor 📖 manual på dansk for Hotpoint HTS15BBMLCC (32 sider) i kategorien Køleskab. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/32
Refrigerators
Top-Freezer
162D6736P007 39-60256 02-03 JR
Safety Information
Adapter Plugs . . . . . . . . . . . . . . . 3
Connecting Electricity . . . . . . . . 3
Extension Cords . . . . . . . . . . . . . 2
Safety Precautions . . . . . . . . . . . 2
Operating Instructions
Automatic Icemaker . . . . . . . . . .8
Care and Cleaning . . . . . . . . 9, 10
Shelves . . . . . . . . . . . . . . . . . . .5, 6
Storage Drawers . . . . . . . . . . . .6, 7
Temperature Controls . . . . . . . . .4
Installation Instructions
Preparing to Install
the Refrigerator . . . . . . . . . . . . 11
Reversing the Door Swing . 16–22
Water Line Installation . . . . 12–16
Troubleshooting Tips
Before You Call
For Service . . . . . . . . . . . . . .24, 25
Normal Operating Sounds . . . .23
Consumer Support
Consumer Support . . . Back Cover
Product Registration . . . . . . 29, 30
Warranty . . . . . . . . . . . . . . . . . . 31
www.Hotpoint.com
Write the model and serial numbers here:
Model #__________________________
Serial # __________________________
You can find them on a label on the upper
left side of the fresh food compartment.
Models
15, 16, 17, 18
Owner’s Manual and
Installation Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
■
■This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
■
■Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
■
■Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet.
Skin may stick to these extremely cold
surfaces.
■
■Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
■
■Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
■
■In refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating
element that releases the cubes. Do not place
fingers or hands on the automatic icemaking
mechanism while the refrigerator is plugged in.
■
■Unplug the refrigerator before cleaning and
making repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
■
■Turning the control to the position does 0
not remove power to the light circuit.
■
■Do not refreeze frozen foods which have
thawed completely.
2
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigerators are still dangerous…even if they
will sit for “just a few days.” If you are getting
rid of your old refrigerator, please follow the
instructions below to help prevent accidents.
Before You Throw Away Your Old
Refrigerator or Freezer:
■Take off the doors.
■Leave the shelves in place so that children
may not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the
company handling the disposal about what
to do.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed,
3-wire grounding type appliance extension cord having a grounding type plug and outlet and
that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
Consumer Support Troubleshooting Tips Operating InstructionsInstallation InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
3
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
www.Hotpoint.com
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock
hazard from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
The refrigerator should always be plugged into
its own individual electrical outlet which has a
voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
USE OF ADAPTER PLUGS
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an adapter plug.
However, if you must use an adapter, where local
codes permit, a temporary connection may be made
to a properly grounded 2-prong wall outlet by use
of a UL-listed adapter available at most local
hardware stores.
The larger slot in the adapter must be aligned
with the larger slot in the wall outlet to provide
proper polarity in the connection of the power
cord.
When disconnecting the power cord from the
adapter, always hold the adapter in place with
one hand while pulling the power cord plug with
the other hand. If this is not done, the adapter
ground terminal is very likely to break with
repeated use.
If the adapter ground terminal breaks, DO NOT
USE the refrigerator until a proper ground has
been established.
Attaching the adapter ground terminal to a wall outlet
cover screw does not ground the appliance unless the
cover screw is metal, and not insulated, and the wall
outlet is grounded through the house wiring. You should
have the circuit checked by a qualified electrician to
make sure the outlet is properly grounded.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
About the temperature control dial.
Control Settings
Temperature Control Dial
The temperature control dial has nine settings plus 0 1. is the warmest. is the coldest. 9
At first, set the dial at 5.
After using the refrigerator, adjust the dial if necessary.
Insert a coin into the slot in the middle of the dial and you can turn the dial to the setting
that’s best suited to your needs.
Allow 24 hours for the refrigerator to get cold.
Turning the dial to stops cooling in both compartments—fresh food and freezer. It does not shut off power to the0
refrigerator.
4
Consumer Support Troubleshooting Tips Safety InstructionsInstallation InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
5
About the fresh food compartment shelves.
www.Hotpoint.com
Shelf supports at various levels allow you to custom-space your shelves. Not all features are on all models.
Full-Width Shelves
Some models have a steel wire sliding
shelf, a stationary tempered glass shelf or
two steel wire stationary shelves. These
shelves can be moved to another place
in the fresh food compartment.
The full-width sliding shelf has stop-locks.
When placed correctly on the shelf
supports, the shelf will stop before coming
completely out of the refrigerator and will
not tilt when you place food on it or
remove food from it.
To remove the full-width shelves, lift the
rear of the shelf and pull forward.
To remove a full-width shelf when the fresh
food compartment door cannot be opened
fully, lift the rear of the shelf, pull
forward and down, tilt the shelf and
take it out.
Half-Width Shelves
One end of the shelf rests on a molded
side-wall support; a bracket on the other
end hooks into a track on the rear
cabinet wall.
To remove, lift the shelf up at front, then
off the support and out of the track.
To replace, select desired shelf height.
With shelf front raised slightly, hook
the bracket’s top lug into the track,
then lower the shelf onto the support.
NOTE: The shelf to the right of the track is
designed to hook into the right-hand slot;
the shelf to the left is designed to hook
into the left-hand slot.
2Lift up and out
1Tilt up
About the freezer compartment shelves.
Some models have an ice-tray shelf and some have a full-width step shelf.
Ice-Tray Shelf
To remove the ice-tray shelf, lift the left
side of the shelf off its supports, then
pull the shelf to the left to free it of the
plug supports. Pull the shelf to the right
to free the pins from the holes in the
cabinet wall.
Step Shelf
To remove the step shelf:
Lift left side of shelf slightly.
Move shelf to the left to free its right
ends from holes in the cabinet wall.
Lower right side of shelf, move shelf
to the right and take it out.
To replace the step shelf:
With shelf tilted as shown, fit left ends
of shelf into holes in cabinet wall.
Lift left side of shelf slightly, swing shelf
up, fit right ends of shelf into holes in
cabinet wall, and lower shelf into place.
2
1
3
2
1
Plug Supports
About the storage drawers.
Not all features are on all models.
Fruit and Vegetable Drawers
Excess water that may accumulate in the
bottom of the drawers should be emptied
and the drawers wiped dry.
Utility Drawer
The utility drawer can be moved to the
most useful location for your family’s
needs.
6
Consumer Support Troubleshooting Tips Safety InstructionsInstallation InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsTroubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
9
Care and cleaning of the refrigerator.
www.Hotpoint.com
Cleaning the Outside
The door handles and trim (on some
models). Clean with a cloth dampened
with soapy water. Dry with a soft cloth.
Keep the outside clean. Wipe with a clean
cloth lightly dampened with kitchen
appliance wax or mild liquid dish
detergent. Dry and polish with a clean,
soft cloth.
Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box
of baking soda in the fresh food and
freezer compartments.
Unplug the refrigerator before cleaning.
If this is not practical, wring excess
moisture out of sponge or cloth when
cleaning around switches, lights or
controls.
Use warm water and baking soda
solution—about a tablespoon (15 ml) of
baking soda to a quart (1 liter) of water.
This both cleans and neutralizes odors.
Rinse and wipe dry.
After cleaning the door gaskets, apply a
thin layer of petroleum jelly to the door
gaskets at the hinge side. This helps keep
the gaskets from sticking and bending
out of shape.
Avoid cleaning cold glass shelves (on some
models) with hot water because the extreme
temperature difference may cause them to
break. Handle glass shelves carefully. Bumping
tempered glass can cause it to shatter.
Do not wash any plastic refrigerator parts in
the dishwasher.
Condenser
There is no need for routine condenser
cleaning in normal home operating
environments. However, in environments
that may be particularly dusty or greasy,
the condenser should be cleaned
periodically for efficient refrigerator
operation.
To clean the condenser, turn the
temperature control dial to 0. Sweep
away or vacuum up dust.
For best results, use a brush specially
designed for this purpose. It is available
at most appliance parts stores.
Cleaning the condenser coils.
11
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT – Save these
instructions for local inspector’s use.
•IMPORTANT – Observe all
governing codes and ordinances.
•Note to Installer – Be sure to leave these
instructions with the Consumer.
•Note to Consumer – Keep these instructions
for future reference.
•Skill level – Installation of this appliance requires
basic mechanical skills.
•Completion time – Refrigerator Installation
15 minutes
Reversing the Door Swing
1 hour
•Proper installation is the responsibility of the
installer.
•Product failure due to improper installation is not
covered under the Warranty.
• Do not install the refrigerator where the temperature
will go below 60°F (16°C) because it will not run often
enough to maintain proper temperatures.
• Install it on a floor strong enough to support it fully
loaded.
REFRIGERATOR LOCATION
If you have questions, call 1.800.GE.CARES or visit our Website at: www.Hotpoint.com
Installation
Refrigerator
Instructions
Models 15, 16, 17, 18
Allow the following clearances for ease of installation,
proper air circulation and plumbing and electrical
connections.
• Sides 3/4″ (19 mm)
• Top 1″ (25 mm)
• Back 1″ (25 mm)
CLEARANCES
Leveling legs near each front corner of the refrigerator
are adjustable. They firmly position the refrigerator
and prevent it from moving when the doors are
opened. Leveling legs should be set so the front of the
refrigerator is raised just enough that the doors close
easily when opened about halfway.
Turn the leveling legs clockwise to raise the
refrigerator, counterclockwise to lower it.
Rollers next to the leveling legs allow you to move the
refrigerator away from the wall for cleaning.
Turn the legs counterclockwise until the weight of the
refrigerator is transferred from them to the rollers.
After rolling the refrigerator back into place, turn the
legs clockwise until the legs again bear the weight of
the refrigerator.
ROLLERS AND LEVELING LEGS
If the refrigerator has an icemaker, it will have to be
connected to a cold water line. A water supply kit
(containing copper tubing, shutoff valve, fittings and
instructions) is available at extra cost from your dealer
or from Parts and Accessories, 800.626.2002.
WATER SUPPLY TO THE ICEMAKER
(on some models)
12
Installation Instructions
INSTALLING THE WATER LINE
1
WHAT YOU WILL NEED
•Copper or approved plastic refrigerator tubing kit,
1/4″outer diameter to connect the refrigerator
to the water supply. If using copper, be sure both
ends of the tubing are cut square.
To determine how much tubing you need: measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8′
(2.4 m). Be sure there is sufficient extra tubing
(about 8 [2.4 m] coiled into 3 turns of about 10′ ″
[25 cm] diameter) to allow the refrigerator to move
out from the wall after installation.
Approved plastic refrigerator tubing kits are available
in the following lengths:
2′ (0.6 m) – WX08X10002
6′ (1.8 m) – WX08X10006
15′ (4.6 m) – WX08X10015
25′ (7.6 m) – WX08X10025
Be sure that the kit you select allows at least 8 (2.4 m)′
as described above.
NOTE: The only approved plastic tubing is that
supplied in the refrigerator tubing kits listed above.
Do not use any other plastic water supply line because
the line is under pressure at all times. Certain types
of plastic will crack or rupture with age and cause
water damage to your home.
BEFORE YOU BEGIN
Recommended copper water supply kits are WX8X2,
WX8X3 or WX8X4, depending on the amount of
tubing you need. Approved plastic water supply lines
are refrigerator tubing kits WX08X10002,
WX08X10006, WX08X10015 and WX08X10025.
When connecting your refrigerator to a reverse
osmosis water system, follow the manufacturer’s
recommendations.
This water line installation is not warranted by the
refrigerator or icemaker manufacturer. Follow these
instructions carefully to minimize the risk of expensive
water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and
lead to water leakage or flooding. Call a qualified
plumber to correct water hammer before installing
the water supply line to the refrigerator.
To prevent burns and product damage, do not hook
up the water line to the hot water line.
If you use your refrigerator before connecting the
water line, make sure the icemaker power switch is
in the position (on power switch models) or theO (off)
feeler arm is in the STOP (up) position (on feeler arm
models).
Do not install the icemaker tubing in areas where
temperatures fall below freezing.
When using any electrical device (such as a power
drill) during installation, be sure the device is double
insulated or grounded in a manner to prevent the
hazard of electric shock, or is battery powered.
All installations must be in accordance with local
plumbing code requirements.
13
Installation Instructions
WHAT YOU WILL NEED (CONT.)
•A water supply kit (containing tubing, shutoff valve
and fittings listed below) is available at extra cost
from your dealer or from Parts and Accessories,
1.888.261.3055.
•A cold water supply. The water pressure must be
between 20 and 120 p.s.i. (1.4–8.1 bar).
•Power drill.
•1/2″or adjustable wrench.
•Straight and Phillips blade screwdriver.
•Two 1/4 outer diameter compression nuts and ″
2 ferrules (sleeves)—to connect the copper tubing
to the shutoff valve and the refrigerator water valve.
OR
•If you are using an approved plastic refrigerator
tubing kit, the necessary fittings are preassembled
to the tubing.
•If your existing copper water line has a flared fitting
at the end, you will need an adapter (available at
plumbing supply stores) to connect the water line to
the refrigerator OR you can cut off the flared fitting
with a tube cutter and then use a compression
fitting. Do not cut formed end from approved
plastic refrigerator tubing.
•Shutoff valve to connect to the cold water line.
The shutoff valve should have a water inlet with a
minimum inside diameter of 5/32 at the point of″
connection to the COLD WATER LINE. Saddle-type
shutoff valves are included in many water supply kits.
Before purchasing, make sure a saddle-type valve
complies with your local plumbing codes.
DRILL THE HOLE FOR THE VALVE
Drill a 1/4 hole in the water pipe (even if using ″
a self-piercing valve) using a sharp bit. Remove any
burrs resulting from drilling the hole in the pipe.
Take care not to allow water to drain into the drill.
Failure to drill a 1/4″hole may result in reduced
ice production or smaller cubes.
3
CHOOSE THE VALVE LOCATION
Choose a location for the valve that is easily
accessible. It is best to connect into the side of
a vertical water pipe. When it is necessary to
connect into a horizontal water pipe, make the
connection to the top or side, rather than at the
bottom, to avoid drawing off any sediment from
the water pipe.
2
Install the shutoff valve on the nearest frequently used
drinking water line.
SHUT OFF THE MAIN WATER
SUPPLY
Turn on the nearest faucet long enough to clear
the line of water.
1
14
Installation Instructions
INSTALLING THE WATER LINE (CONT.)
1
FLUSH OUT THE TUBING
Turn the main water supply on and flush out the
tubing until the water is clear.
Shut the water off at the water valve after about
one quart (1 liter) of water has been flushed
through the tubing.
8
CONNECT THE TUBING
TO THE VALVE
Place the compression nut and ferrule (sleeve)
for copper tubing onto the end of the tubing and
connect it to the shutoff valve.
Make sure the tubing is fully inserted into the
valve. Tighten the compression nut securely.
For plastic tubing from an approved refrigerator
tubing kit, insert the molded end of the tubing into
the shutoff valve and tighten compression nut until
it is hand tight, then tighten one additional turn
with a wrench. Overtightening may cause leaks.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
7
Saddle-Type
Shutoff Valve
Compression
Nut
Approved
Plastic Tubing
Packing Nut
Outlet Valve Ferrule (sleeve)
FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with
the pipe clamp.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
4
Vertical Cold
Water Pipe
Saddle-Type
Shutoff Valve
Pipe Clamp
TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer
begins to swell.
NOTE: Do not overtighten or you may crush the
tubing.
5
Washer
Inlet End
Pipe Clamp
Clamp Screw
ROUTE THE TUBING
Route the tubing between the cold water line and
the refrigerator.
Route the tubing through a hole drilled in the wall
or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing
(about 8 feet [244 cm] coiled into 3 turns of about
10″[25 cm] diameter) to allow the refrigerator to
move out from the wall after installation.
6
15
Installation Instructions
CONNECT THE TUBING
TO THE REFRIGERATOR
NOTES:
•Before making the connection to the refrigerator,
be sure the refrigerator power cord is not plugged
into the wall outlet.
•We recommend installing a water filter if your
water supply has sand or particles that could clog
the screen of the refrigerator’s water valve. Install
it in the water line near the refrigerator. If using
an approved plastic refrigerator tubing kit, you
will need an additional tube (WX08X10002) to
connect the filter. Do not cut plastic tube to
install filter.
Remove the access cover.
Remove the plastic flexible cap from the water
valve (refrigerator connection).
Place the compression nut and ferrule (sleeve)
onto the end of the tubing as shown. On an
approved plastic refrigerator tubing kit, the nuts
are already assembled to the tubing.
Insert the end of the tubing into the water valve
connection as far as possible. While holding the
tubing, tighten the fitting.
For plastic tubing from an approved refrigerator
tubing kit, insert the molded end of the tubing into
the shutoff valve and tighten compression nut until
it is hand tight, then tighten one additional turn
with a wrench. Overtightening may cause leaks.
9
TURN THE WATER ON AT THE
SHUTOFF VALVE
Tighten any connections that leak.
10
CONNECT THE TUBING TO THE
REFRIGERATOR (CONT.)
Fasten the tubing into the clamp provided to
hold it in a vertical position. You may need to
pry open the clamp.
Reattach the access cover.
9
Tubing Clamp
1/4″Compression
Nut
Ferrule
(sleeve)
Approved
Plastic Tubing
Refrigerator
Connection
1/4″Copper
Tubing
16
Installation Instructions
REVERSING THE DOOR SWING
2
When reversing the door swing:
•Read the instructions all the way through before
starting.
•Handle parts carefully to avoid scratching paint.
•Set screws down by their related parts to avoid using
them in the wrong places.
•Provide a non-scratching work surface for
the doors.
IMPORTANT: Once you begin, do not move the
cabinet until door-swing reversal is completed.
These instructions are for changing the hinges from
the right side to the left side—if you ever want to change
the hinges back to the right side, follow these same
instructions and reverse all references to left and right.
IMPORTANT NOTES
Phillips screwdriver
TOOLS REQUIRED
Masking tape
T20 or T25 Torxdriver,
(needed for some
models)
5/16 hex-head ″
socket driver
5/16 open-end″
wrench
Putty knife or thin-blade
screwdriver
PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it does not vibrate
against the back of the refrigerator or against the
wall. Push the refrigerator back to the wall.
11
On power switch models, set the icemaker power
switch to the position. On feeler arm models,l (on)
move the feeler arm to the ON (down) position. The
icemaker will not begin to operate until it reaches
its operating temperature of 15°F (–9°C) or below.
It will then begin operation automatically.
NOTE: In lower water pressure conditions, the
water valve may turn on up to 3 times to deliver
enough water to the icemaker.
START THE ICEMAKER
Power
switch
Power switch model
Feeler Arm in the
STOP (up) position
Feeler Arm in
the ON (down) position
Feeler arm model
12
INSTALLING THE WATER LINE (CONT.)
1

Produkt Specifikationer

Mærke: Hotpoint
Kategori: Køleskab
Model: HTS15BBMLCC

Har du brug for hjælp?

Hvis du har brug for hjælp til Hotpoint HTS15BBMLCC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Køleskab Hotpoint Manualer

Hotpoint

Hotpoint HTSD184011A1 Manual

12 Marts 2025
Hotpoint

Hotpoint HTSD18A011A1 Manual

12 Marts 2025
Hotpoint

Hotpoint SH8 A2Q GRD Manual

12 Marts 2025
Hotpoint

Hotpoint SH6 A2Q WR Manual

12 Marts 2025
Hotpoint

Hotpoint LECO8 FF2 Manual

25 Februar 2025
Hotpoint

Hotpoint HTH17BCCRWW Manual

15 Januar 2025
Hotpoint

Hotpoint RFAA52P Manual

13 Januar 2025
Hotpoint

Hotpoint LH8 FF2I X Manual

11 Januar 2025
Hotpoint

Hotpoint HAT70 832 X Manual

10 Januar 2025
Hotpoint

Hotpoint H8 A1E W Manual

29 December 2024

Køleskab Manualer

Nyeste Køleskab Manualer

Whirlpool

Whirlpool ARG 746/A+/5 Manual

25 Marts 2025
Bosch

Bosch KTR15NWEAG Manual

22 Marts 2025
Caple

Caple RBL6 Manual

21 Marts 2025
FrigeluX

FrigeluX CBNF177BI Manual

20 Marts 2025
Café

Café CWE19SP2NS1 Manual

16 Marts 2025
Bosch

Bosch B36FD30ENS Manual

15 Marts 2025
Bosch

Bosch KTR15NWECG Manual

13 Marts 2025
Hisense

Hisense HRBF126 Manual

13 Marts 2025
Café

Café CWE19SP3ND1 Manual

11 Marts 2025
Exquisit

Exquisit KGC265-70-040D Manual

10 Marts 2025