HP BLc3000 Manual

HP Server BLc3000

Læs nedenfor 📖 manual på dansk for HP BLc3000 (2 sider) i kategorien Server. Denne guide var nyttig for 50 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
HP c3000 DDR2 Onboard
Administrator
Installation Instructions
for HP BladeSystem c3000 and c3000 Tower Enclosure
Introduction
There are two optional Onboard Administrator modules available
with the enclosure:
HP c3000 DDR2 Onboard Administrator module, part number
488099-B21
HP c3000 Dual Onboard Administrator module, part number
488100-B21
To use the Onboard Administrator modules, you must have HP
BladeSystem Onboard Administrator version 2.30 or greater
installed. For more information on using the Onboard Administrator
software, see the HP BladeSystem Onboard Administrator User
Guide.
You can install the optional HP c3000 DDR2 Onboard Administrator
module in the enclosure without a second module.
Before you install an HP c3000 Dual Onboard Administrator in the
enclosure, you must have installed the c3000 DDR2 Onboard
Administrator module.
NOTE: The HP BladeSystem c3000 Enclosure is shown
in the illustrations throughout this document. The HP
BladeSystem c3000 Tower Enclosure is rotated 90
degrees clockwise from what is shown in the
illustrations.
HP c3000 DDR2 Onboard
Administrator module components
Item Name Description
1 Insight Display A display that
provides
information about
the health and
operation of the
enclosure
2 Serial connector Serial RS232 DB-9
connector with PC
standard pinout.
3 UID LED Blue = UID on
Dark = UID off
Item Name Description
4 Active Onboard
Administrator LED
An LED that
indicates which
Onboard
Administrator is
active
5 Health LED Green = OK
Red = Critical error
6 USB A USB 2.0 Type A
connector that
connects supported
USB devices
7 Reset button
HP c3000 Dual Onboard
Administrator module components
Item Name Description
1 Serial connector Serial RS232 DB-9
connector with PC
standard pinout
2 UID LED Blue = UID on
Dark = UID off
3 Active Onboard
Administrator LED
An LED that
indicates which
Onboard
Administrator is
active
4 Health LED Green = OK
Red = Critical error
5 USB USB 2.0 Type A
connector that
connects supported
USB devices
6 Reset button
Upgrading an HP Onboard
Administrator module to an HP
c3000 DDR2 Onboard
Administrator module
1. Disconnect all cables from the HP Onboard Administrator
module.
2. Remove the HP Onboard Administrator module.
3. Slide either the c3000 Dual Onboard Administrator module (if
ordered) or an Onboard Administrator blank into the c3000
DDR2 Onboard Administrator module, and close the handle.
© Copyright 2008, 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-
Packard Com
p
an
y
under license.
Part Number 488456-002
September 2009 (Second Edition)


Produkt Specifikationer

Mærke: HP
Kategori: Server
Model: BLc3000
Vægt: 1810 g
Ethernet LAN-porte (RJ-45): 1
Antal USB 2.0-porte: 1
Certificering: CE, FCC
Antal serielle porte: 1

Har du brug for hjælp?

Hvis du har brug for hjælp til HP BLc3000 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Server HP Manualer

Server Manualer

Nyeste Server Manualer

MSI

MSI N5010 Manual

18 December 2024
MSI

MSI N1000a Manual

18 December 2024
Gigabyte

Gigabyte TO24-JD0 Manual

15 December 2024
Digitus

Digitus DN-170108 Manual

13 December 2024
APC

APC RBC55 Manual

11 December 2024
Asus

Asus TS700-E6/RS8 Manual

9 December 2024
Dell

Dell PowerEdge C6300 Manual

8 December 2024
Dell

Dell NX430 Manual

8 December 2024
APC

APC AP8653 Manual

7 December 2024