Hudson Valley Arietta 6500-AGB Manual

Hudson Valley Lys Arietta 6500-AGB

Læs nedenfor 📖 manual på dansk for Hudson Valley Arietta 6500-AGB (2 sider) i kategorien Lys. Denne guide var nyttig for 13 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
6500
Thank you for purchasing our lighting fixture.
Please clean with a soft, dry cloth ONLY! Do not
use cleansers.
www.hudsonvalleylighting.com
GENERAL
1. To ensure successful installation, the following instructions and agram(s) should di
be read and understood.
2. All electrical connections must be made in accordance with the National Electric
code and local codes and ordinances. If you are uncertain how to install electrical
wiring and lighting fixtures, secure the services of a qualified licensed electrician.
TOOLS NEEDED
Blade screwdriver, phillips screwdriver, slip joint pliers or small adjustable wrench,
wire cutter/stripper, electrical current tester, stepladder and electrical tape.
INSTALLATION PREPARATION
1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH
THE LIGHTING FIXTURE IS TO BE ATTACHED. Turn circuit breaker
to the off position or completely remove the fuse controlling the circuit.
2. If an existing fixture is being replaced, remove it and note to which of the
wires in the outlet box the fixture was attached. DO NOT SEPARATE
MULTIPLE TWISTED WIRES THAT MAY BE IN THE BOX. DO
NOT DAMAGE THE INSULATION OF OLDER WIRING. In regular
circumstances the BLACK wire will be the “Hot” lead and the WHITE wire will
be the “Neutral” or “Common” lead. A GREEN or BARE COPPER wire is the
“Ground”. In older buildings it is always good practice to reconfirm the polarity
of the wiring.
3. This fixture is designed to be mounted on an octagon box. The box must be
securely mounted to the structure of the building.
FIXTURE INSTALLATION
1.Remove the fixture and parts bag(s) from the carton. Before discarding the
carton, double check packing to make certain that all parts are found.
2. Attach the mounting bar to the outlet box. (The green screw should face out).
Pull wires out of box. Thread the nipple onto the mounting bar.
3. Fasten the bare ground wire to the green or bare copper wire in the outlet box
or the green screw on the crossbar.
NEVER FASTEN THE GROUND WIRE TO THE BLACK OR "HOT"
WIRE ! FAILURE TO FOLLOW THIS INSTRUCTION COULD
RESULT IN SERIOUS INJURY OR DEATH !
4. Fasten the fixture lead with the ridge(s) to the white wire in the outlet box.
Fasten the wires together with an approved fastener (wire nut) arting about 1" St
below the fastener, tightly wrap the connetion with electrical tape so that the tape
seals the end of the fastener. Make sure that there is no exposed wire or
strands that could cause a dangerous short circuit !
5. Connect the black fixture wires to the black wire in the outlet box. Fasten the
joined wires as in step 4.
6 Place the canopy over the outlet box and fasten it by the ball nut. .
7. Install the lamp, The fixture is rated for 60 watt type C lamp.
DO NOT EXCEED RECOMMENDED WATTAGE !
8. Restore power to circuit at breaker or fuse box.
NOTE: The important safeguards and instructions outlined on this sheet are not
meant to cover all possible conditions and situations that may occur. It must be
understood that common sense, caution and care are factors that cannot be built
into any product. Caution and care must be supplied by the person(s) installing,
operating and maintaining this lighting fixture.


Produkt Specifikationer

Mærke: Hudson Valley
Kategori: Lys
Model: Arietta 6500-AGB

Har du brug for hjælp?

Hvis du har brug for hjælp til Hudson Valley Arietta 6500-AGB stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys Hudson Valley Manualer

Lys Manualer

Nyeste Lys Manualer

Nanlite

Nanlite D672BII Manual

19 December 2024
Nanlite

Nanlite Compac 40 Manual

19 December 2024
Nanlite

Nanlite MixPad II 11C Manual

18 December 2024
Nanlite

Nanlite D672II Manual

18 December 2024
Chauvet

Chauvet WELL POD 2X6 Manual

17 December 2024
Luxli

Luxli ORC-VIOLA-M2 Manual

17 December 2024
Makita

Makita DML817 Manual

16 December 2024
Makita

Makita MT001 Manual

16 December 2024