Iget M3P15V2 Manual

Iget Overvågningskamera M3P15V2

Læs nedenfor 📖 manual på dansk for Iget M3P15V2 (6 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 10 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/6

Safety precautions

Individual parameters, description by figures and design in the manual may differ depending on the version

and updates. Printing errors reserved. The buyer is obliged to provide a serial number on the warranty card as

well as in the delivery note and the proof of purchase. In this context, the buyer acknowledges that unless the

serial number of goods is not marked on the proof of purchase, delivery note and in the warranty card and

therefore it cannot be possible to compare this serial number marked on goods and its protective packaging

with the serial number stated in the warranty card, delivery note and the proof of purchase and thus to verify

that the goods runs from the seller, the service center is competent to claim such a goods automatically and

reject it immediately. The buyer must instruct all persons to whom the goods would be subsequently sold.

Product complaints do with your dealer if you are not on the web www.iget.eu indicated otherwise.

For household use: The given symbol (crossed-out wheeled bin) on the product or at accompanying

documents means that used electrical and electronic products should not disposed of with household waste.

To ensure proper disposal of the product, hand it over to a designated collection point, where it will be

accepted free of charge. The correct disposal of this product will help to save valuable natural resources and

prevent any potential negative impacts on the environment and human health, which could otherwise be

caused by inappropriate disposal of wastes. For more details, please, contact your local authorities or the

nearest collection point. The improper disposal of this waste can be penalized in accordance with national

regulations. Information for users to disposal of electrical and electronic devices (corporate and business use):

For proper disposal of electrical and electronic devices, ask for details from your dealer or distributor.

Information for users to disposal of electrical and electronic devices in other countries outside EU: The above

mentioned symbol (crossed-out wheeled bin) is valid only in the countries of EU. For proper disposal of

electrical and electronic devices, ask for details from your authorities or dealer. All is expressed by the symbol of

crossed-out wheeled bin on product, packaging or in printed materials.

Set up the claim for warranty repair of device at your dealer. If you have technical questions or problems,

contact your dealer. Follow the rules for working with electrical equipment. The user may not dismantle the

device or replace any part of this. Opening or removing the covers poses the risk of electric shock.

Declaration of Conformity:

Company INTELEK spol. s r.o. hereby declares that all M3P15v2 devices are in compliance /M3P18v2/M3P20v2

with essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU

Declaration of Conformity is available on this website www.iget.eu.

The warranty period of the product is 24 months, unless stated otherwise.

This device can be used in the following countries:

RoHS: The components used in the device meet the requirements on the restriction of hazardous substances in

electrical and electronic devices in accordance with Directive 2011/65/EU. The RoHS declaration can be

downloaded from www.iget.eu.

Producer / Exclusive importer of iGET products to EU:

INTELEK spol. s r.o., Ericha Roučky 1291/4, 627 00 Brno - Černovice, CZ, web: http://www.iget.eu

SUPPORT: http://www.iget.eu/helpdesk

Insert Lan Cable and Power Up

Please lways onnect mart amera ith AN efore a c S C w L b

powering up when you first using it.

• Make sure the the settings like DHCP Server and UPNP are

enabled on your router.

• Connec pow cable Smar Camer r some t the er , the t a will un

diagnostic proc like rolling the camer W it stops esses a. hen

rolling, the startup is completed.

Pairing with system

T “+” dd accessory to scan QR codes printed on the backap A cover

of the camera. Then name the camera for daily use. After that,

you’ve successfully paired the camera with system.

EN M3P15v2/M3P18v2/M3P20v2 iGET

Setting Up Camera M3P15v2/M3P18v2

Setting Up Camera M3P20v2

Power up

• Insert power cable into the Micro-USB slot on the round edge.

•The camera will power up you will hear the prompt voice to

show you it is waiting to WiFi settings.

Pairing with system

Tap “+” Add accessory to scan QR codes printed on the back

cover of the camera, you will be guided to connect to Camera by

connected the AP started with IPCAM-XXXXXX.

WiFi Settings

•After switch back to App, you will have the page to set up WiFi

of camera.

•Select your WiFi router in the list, then input Password and Save.

•You will hear the camera play a special tone that means it was

connected to the router successfully.

•Name it, then getting started to use camera.

FAQ

I’ve Already Connected My Camera to Internet, But I Can’t Connect It in App.

Please make sure your router has successfully connected to Internet.

DHCP Server/Service should be Enable on the router. UPNP should be Enable too.

Your phone’s data plan should be available. Some carriers restricts the p2p connection protocol, try using App in the Wi-Fi with Smart Camera to same

figure out the problem. If you still can’t connect it, try another router if possible. Some routers’ build-in firewall also interfere the connection.

I Can’t Save the Snapshots.

App will need to access to your phone’s album for saving The authorization might need you to approve while using the function for the snapshots.

first time in some phones. If you mis-click the ‘No’ option during the authorization, you might need to enable it in the system setting menu.

How to Reset My Camera?

PLEASE MAKE SURE YOU CLEARLY KNOW THE RESULT OF RESETING: ALL DATA WILL BE ERASED INCLUDING THE INTERNET SETTINGS.

Power up your Smart Camera, wait until the camera stops rolling. Hold the reset button for a while until the camer starts rolling again. Release the a

button then the Smart Camera would be reset.