Intelix AVO-VGA Manual

Intelix Skifte AVO-VGA

Læs gratis den danske manual til Intelix AVO-VGA (4 sider) i kategorien Skifte. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Intelix AVO-VGA, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Intelix AVO-VGA

Installation Manual

Introduction

The Intelix AVO-VGA balun set transmits VGA video passively over standard unshielded

twisted pair cable, such as Cat 5, Cat 5e or Cat 6. The AVO-VGA eliminates costly and

bulky VGA cable, and extends video transmission distances.

Pre-Installation

The AVO-VGA features shielded RJ45 connectors, which are provided as an option in

harsh electrical environments, such as installations with large motors or cable runs

near sources of interference. In such environments, shielded twisted pair cable (STP) may

provide additional noise immunity. When using STP, ensure the shield on both ends of the

cable run is terminated to a shielded RJ45 connector.

Note: The AVO-VGA does not support VGA handshakin

and control si

nals.

Therefore, it is necessar

to set the monitor attributes prior to installin

the balun set.

First connect the source (typically a computer) directly to the destination (typically a

monitor) with a standard VGA cable. After doin

so, set the monitor attributes to the

required settin

s (i.e., resolution, color, etc.). For best results, also set the contrast and

htness to the maximum level.

Caution: Do not attempt to disassemble or alter the balun housin

. There are no

user-serviceable parts inside the unit. Doing so will void your warranty.

Installation

1. Power off the source and destination devices which will be connected to the baluns.

2. Verify the modular outlets and cross connects to which you will connect the AVO-

VGA are configured properly and labeled appropriately to identify the circuit.

3. Verify the desired twisted pairs are not being used for other LAN or telephone

equipment.

4. Connect the send balun (AVO-VGA-S) to the VGA port of the source equipment.

Tighten the mounting screws on each balun.

5. Connect one end of the twisted pair cable to the send balun. The RJ45 pinout in the

twisted pair cabling should conform to the EIA/TIA 568A or 568B standard.

6. Connect the receive balun (AVO-VGA-R) to the destination equipment.

7. Connect the other end of the twisted pair cable to the receive balun. The RJ45 pinout

in the twisted pair cabling should conform to the EIA/TIA 568A or 568B standard.

8. Power on the source and destination equipment.

9. If necessary, set monitor contrast and brightness to the desired levels.

10. Set the monitor refresh rate to the optimal rate for the display at the desired resolution.

11. If necessary, adjust the image quality with the Sync Adjust switch on the send and

receive baluns. It is recommended that both switches be in the same position.

Caution: Do not connect the balun to a telecommunication outlet wired to

unrelated equipment. Doin

so ma

dama

e the unit or an

connected equipment.

Ensure all connected twisted pair cabling is straight-through (point-to-point).

Caution: To minimize the possibilit

of equipment dama

e from electrostatic

discharge (ESD), all source and destination equipment must be powered off durin

installation. This includes signal extenders, splitters, and switches.

Note: For your convenience, it is recommended that

ou uniquel

mark the ends

of the twisted pair cable before pulling them through a wall or conduit.

Note: The AVO-VGA features an optional grounding screw that may be used to

correct an

ima

e anomalies, such as differences in hue from one side of a monitor to

the next. Should this occur, connect the balun

round to earth

round. However, if the

building has a grounding problem, such as ground loo

roundin

the balun ma

negatively affect the signal. Only ground the AVO-VGA if it positivel

affects the

nal.

Produkt Specifikationer

Mærke:	Intelix
Kategori:	Skifte
Model:	AVO-VGA

Har du brug for hjælp?

Hvis du har brug for hjælp til Intelix AVO-VGA stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skifte Intelix Manualer

Intelix AVO-VGA Manual

8 Juni 2024

Skifte Manualer

Nyeste Skifte Manualer

Lancom GS-2412 Manual

4 April 2025

Lancom GS-2412P Manual

4 April 2025

Lancom GS-2426 Manual

4 April 2025

Hager ARF970D Manual

3 April 2025

Hager ARF920D Manual

3 April 2025

Roline 14.01.3579 Manual

2 April 2025

Fantini Cosmi B12BN Manual

1 April 2025

Fantini Cosmi B12DN Manual

1 April 2025

Fantini Cosmi B12GN Manual

1 April 2025

Fantini Cosmi B12HN Manual

1 April 2025