Intermatic ST01 Manual

Intermatic Skifte ST01

Læs nedenfor 📖 manual på dansk for Intermatic ST01 (2 sider) i kategorien Skifte. Denne guide var nyttig for 19 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Connect the GREEN wire to the grounding screw in the box. If

a plastic box, connect to ground as supplied.

Make sure all twist connectors are tight.

If a 3-Way Switch Setup:

NOTE: The distance between

switch timer and remote switch

must not exceed 100 feet.

Locate the COMMON

wire connected to ﬁrst old

switch. It might be attached

to a different colored screw,

or ﬁnd markings on old switch.

Connect BLACK wire from switch timer to COMMON wire,

using a twist connector.

Connect the other two wires from the old switch to the Blue

and RED wires from the switch timer.

Connect the GREEN wire to the grounding screw in the box. If

a plastic box, connect to ground as supplied.

Using diagram #1 below. Identify and remove wire “C” from

the “Common” terminal of your existing remote switch.

Using diagram # 2 below, remove and reconnect wires “B”

and “C” to the “Common” terminal of your remote switch,

using the supplied piece of jumper wire, if necessary. Follow

diagram # 3 below, if using a new single-pole remote switch.

NOTE: For new construction or to replace a dimmer switch,

a lighted switch, or a 3-way switch without screw terminals,

a single-pole switch can be used at the remote location, as

shown.

NOTE: If the building’s wiring colors don’t allow you to tell

wire “A” from “B,” just pick one of the two wires and connect

as if it is wire “B.” After the installation is complete, if the con-

trolled light or device will not turn on properly, simply reverse

wires “A” and “B.” See Steps J and K for how to check.

Tuck wires into the timer wall box leaving room for the timer.

Using screws provided, mount the switch timer into the wall

box, then install the wall plate.

Install the remote 3-way switch in its box and install wall

plate. Turn the power back on at the service panel.

Make sure the switch timer displays “MAN” mode. Do the fol-

lowing test with the remote switch in each of its 2 positions:

Press the ON/OFF button on the switch timer several times.

Each time that you push the ON/OFF button, the switch timer

should “click” and the controlled light or device (the “load”)

should turn on or off. If so, proceed to Step K.

If the timer clicks but the load does not operate, re-check

your wiring and make sure the load is functional.

Self-Adjusting Wall Switch Timer

Turn off power at the service panel by REMOVING FUSE or

TURNING THE CIRCUIT BREAKER OFF.

Remove the existing wall switch.

Trim building wires to 7/16” as shown.

If a Single Switch Setup:

Connect one of the two wires

from the wall to the black wire

from the switch timer, using

the twist connectors provided.

Connect the other wire from

the wall to the blue wire from

the switch timer, using the

twist connectors provided.

NOTE: The RED wire is not used in single-switch installations.

Cap with a twist connector.

Resistive (heater) 15 Amp, 120-277 VAC

Tungsten (incandescent) 15 Amp @ 120 VAC, 6 Amp @ 208-277 VAC

Ballast (ﬂuorescent) 8 Amp @ 120 VAC, 4 Amp @ 208-277 VAC

Motors 1 H.P. @ 120 VAC, 2 H.P. @ 240 VAC

DC Loads 4 Amp @ 12 VDC, 2 Amp @ 28 VDC

•

Installation and User Instructions

MODEL ST01 Series

2 – Install the Switch Timer

Ratings

Before installing the switch timer into the wall, make sure the

supplied battery is installed and working.

Open the access door to reveal the battery tray, located below

the ON/OFF keypad.

If there is a pull tab at the battery tray, remove the tab to con-

nect the installed battery. Make sure battery tray is pushed

fully into place. Proceed to Step 6.

If the battery was supplied loose, use a ﬂat screwdriver to pry

loose the battery tray.

Place the supplied “CR2” battery into the tray, observing +

and – markings on tray.

Replace the battery tray into the switch timer.

The display will initialize itself then ﬂash “12:00 AM” in

MANual mode.

Press the ON/OFF button. The switch timer should “click.”

NOTE: If display doesn’t ﬂash “12:00 am”, the battery may be

dead. Replace the battery before installing the switch timer.

1 – Before Installing Switch Timer, Install and Check Battery

BLACK WIRE

BLUE WIRE

RED WIRE

(capped, not connected)

RED WIRE

BLUE WIRE

BLACK WIRE

WIRE FROM

“COMMON” OF

OLD SWITCH

7/16”

DIAGRAM 1:

TYPICAL

EXISTING

2-SWITCH

SETUP

LOAD

NEUTRAL

3-WAY

MAIN SWITCH

WIRE “A”

“COMMON” TERMINAL

LINE

3-WAY

REMOTE SWITCH

WIRE “B”

WIRE “C”

DIAGRAM 2:

2-SWITCH SETUP,

TIMER INSTALL

RE-USING EXISTING

REMOTE 3-WAY SWITCH

LOAD

NEUTRAL

WIRE “A”

“COMMON” TERMINAL

LINE

3-WAY

REMOTE SWITCH

WIRE “B”

NOT USED

BLACK

TIMER

BLUE

RED

WIRE “C”

JUMPER

DIAGRAM 3:

2-SWITCH SETUP,

TIMER INSTALL USING

NEW SINGLE-POLE

REMOTE SWITCH

LOAD

NEUTRAL

WIRE “A”

LINE

SINGLE-POLE

REMOTE SWITCH

WIRE “B”

BLACK

TIMER

BLUE

RED

WIRE “C”

JUMPER

158ST13133

Observed Problem Possible Cause What to Do

Switch timer does not switch ON/OFF but

display looks normal.

Switch timer is not set in AUTO, RANDom, or

MANual mode.

Press MODE to select the operational mode you

want to use.

Switch timer won’t enter AUTO or

RANDom mode when you press MODE.

The time of day or timer settings have not

been set.

Make sure the time of day and at least one sched-

uled activity have been set.

Switch timer switches at incorrect times

or skips some of the programmed times.

Programmed schedule(s) are incorrect. Press ON/OFF to review the settings and revise

them as necessary. See instructions at the left.

Switch timer is in RANDom mode, which var-

ies switching times up to ±20 minutes (to give

your home a “lived-in” look).

If you don’t want to keep the switch timer in

RANDom mode, press MODE to change to AUTO

mode.

The Astronomic and Speciﬁc switching times

are in conﬂict. For example, you’ve set ON to

DUSK and OFF at 8 pm, and due to seasonal

changes, DUSK has advanced to 8:30 pm.

NOTE: Your switch timer automatically skips

any conﬂicting ON event as summer ap-

proaches to prevent unwanted operation of

lights or other controlled devices. See “What

to Do” if you want to identify and remove

conﬂicting settings.

Complete the steps for setting the Time and

Date, then temporarily change the date to

June 21st.

Review the DAWN and DUSK settings by

pushing the ON/OFF button.

Make sure the speciﬁc ON or OFF time set-

tings won’t interfere with these DAWN and

DUSK times. Make changes as necessary.

When ﬁnished, change the Date setting back

to today’s date.

The lights or controlled devices don’t

match the programmed ON/OFF status

immediately after setting the time or

programming a schedule.

Switch timer does not “catch up” automati-

cally to the programmed load state. The status

of the switch timer will remain as is until it

comes to the next programmed ON/OFF time.

After entering your schedules or the time, then

returning to the AUTO mode, push the ON/OFF but-

ton to change the load state if necessary.

Load only operates when the remote

(3-way) switch is in one position, or the

switch timer ignores the remote switch.

The remote switch is wired incorrectly.

Recheck the wiring, especially for the jumper,

according to “If a 3-way Switch Timer” and “If a

Multiple Switch Timer Setup.”

The switch timer ignores a 3-way remote

switch even though it is wired correctly.

There is an excessive length of wire (more

than 100 feet), or there is buried wire to the

switch.

Eliminate the condition: either replace the buried

cable, do without the remote switch, or contact

Intermatic Customer Service for more options.

The remote switch is not functioning properly

or worn out. Replace the remote switch.

The load turns off immediately after being

turned on.

The remote switch or switch timer is wired

wrong.

There is an excessive length of wire

(greater than 100 feet)

There is buried wire to the remote switch.

The switch timer is not functioning properly.

•

If the problem persists with the switch timer’s red

wire disconnected or with a remote switch tempo-

rarily connected right at the switch timer, replace

the non-functioning switch timer. Otherwise, try

the above suggestions.

The battery tray is difﬁcult to replace.

Battery is not seated in the tray.

The tray is misaligned.

The contact tabs of the tray are bent.

•

Seat the battery in the tray, then reinstall.

The switch timer operation is sluggish or

not switching ON/OFF at all.

Though the “BATT” message is not being

displayed, the battery is getting weak.

Replace the battery. To test the battery, press the

ON/OFF button. The timer should “click.”

Timer shows ON but the light or other

controlled device is OFF.

The light or controlled device itself may be

switched OFF.

Make sure the light or controlled device is

switched ON and plugged in.

Troubleshooting Guide

LIMITED ONE-YEAR WARRANTY

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is

extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use;

(b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modiﬁed; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed

lamps and/or lamp bulbs, LED’s and batteries; (f) the ﬁnish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs,

removal costs, or reinstallation costs.

INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE

WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF

THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO

YOU.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized

service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap