Joblotron JA-80F Manual

Joblotron Overvågningskamera JA-80F

Læs nedenfor 📖 manual på dansk for Joblotron JA-80F (1 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

The JA-80F wireless keypad MHE51302 1

The JA-80F wireless keypad

The JA-80F is a component of Jablotron’s OASiS alarm system and is

designed to control and program the system. It has a built-in proximity access

card reader and allows the wiring up of a separate door detector. The battery-

powered keypad communicates wirelessly using OASiS protocol.

Installation

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor. The keypad is for indoor installation

only, typically by the main entrance door. Avoid locating it close to metal

objects which could shield radio communication.

1. Open the keypad housing (by pressing the tab on the bottom) and

disconnect the inter-housing connection cable inside (by pulling the

connector from the board)

2. Install the rear housing to the desired location

3. Install the external hard-wired detector (if required) and route its

cable through the rear housing

4. Enroll the keypad to the control panel (see the control panel

installation manual) as follows:

• Enter enrollment mode in the control panel (if the system does

not have a keypad already, briefly short the reset link on the

control panel main board, or if a keypad is present, then press

key 1 in service mode).

• Install the battery into the keypad to trigger enrollment.

• Exit enrollment mode by pressing the # key.

5. Connect the inter-housing cable to the board. If a door detector

and an external AC adaptor are used, then connect their cables too.

Attach the keypad to the rear housing.

6. Instructions on how to use the keypad can be found in the control

panel operating manual.

Installing a door detector

It is possible to wire up a detector(s) to the keypad. The IN input terminal is

triggered when disconnected from GND. The control panel’s natural reaction

to the IN input being triggered is a delayed intruder alarm linked to the

keypad‘s address. If desired, another reaction can be programmed in the

control panel. The IN input can indicate a door being permanently open

(status reaction). If the IN input is never used then it must be shorted to GND.

Note: The lifetime of

the battery is reduced

proportionally to how

frequently the door

detector is triggered

and how often and how

long the keypad is

battery-powered.

Keypad sleep mode

When battery-powered, the

keypad saves energy by

turning itself off when the cover is closed or automatically after 20 seconds of

inactivity (15 minutes in service mode). The keypad is woken up by: opening

the keypad‘s flip cover, pressing any key, or triggering the wired door detector.

Recommendation: install the keypad with the door detector wired to its

IN terminal. The door detector will always turn the keypad on when the door

is opened and the keypad can also indicate the entrance delay and be ready

to read access cards. You will also save money on a wireless door detector.

Note: If the keypad unit is powered by an AC adaptor there is no sleep mode,

but 3 minutes after setting the system, status indication stops. If desired, the

system setting/unsetting status can be programmed in the control panel to be

permanently indicate by the keypad.

Optional AC adapter

If the keypad is powered by an AC adapter (model: Jablotron DE01-12 for

terminals: +U and GND), it will not turn off after 20 seconds of inactivity. If

the adapter is used, batteries should still be installed. Only turn on the AC

adapter after the keypad unit has been powered up by batteries and the

two halves of the housing are back together.

Keypad menu – language selection and door bell function

If the ∗ key is kept pressed during battery connection the internal keypad

menu will be displayed allowing the selection of the desired language. Using

the arrows choose your language and confirm selection by the ∗ key.

In this menu the door bell function can also be enabled or disabled (if

enabled the keypad makes a sound when its IN input is triggered).

Notes:

• The menu can be displayed even if the keypad has not been enrolled to

the control panel.

• If you wish to display the menu on a keypad which already has its

battery installed, disconnect and reconnect the batteries first.

• Each keypad has its own menu, i.e. each keypad in the system can

have its own unique settings.

• The keypad keeps its settings even if its power is disconnected (settings

can only be altered via the keypad menu).

Testing keypad communication

In service mode, the control panel allows the keypad’s radio signal to be

checked, including signal strength measurement. To test the keypad

signal, trigger either its IN input or its tamper sensor.

Note: the control panel measures the strength of the signal transmitted

by the keypad. It is impossible to measure the signal strength received by

the keypad from the control panel. If the keypad has lost communication

with the control panel (e.g. if the control panel is damaged) it would

display a communication error. If you re-power a control panel which

previously worked with a keypad, and the keypad does not function, then

we recommend disconnecting and re-connecting the keypad batteries.

Disabling the tamper sensor

To disable the tamper sensor, short out the jumper in the keypad unit

close to the tamper sensor (equipped with a spring). This is useful when

carrying the keypad unit around while servicing the system. During

normal use of the system this jumper must remain open circuited.

Keypad text editing

There are two kinds of text: device and code names (displayed on the

second line after the address number) and other system text.

The names can be edited via the keypad after pressing and holding the

? key in service mode – see the control panel installation manual. The

edited text is only stored in the keypad unit used for editing.

The most convenient way to edit text is to use a PC running OLink

software. To transfer edited text from a PC to the keypad, the keypad

(with its batteries installed) has to be connected to the OASiS system‘s

digital bus (i.e. one cable from the keypad to the control panel, and

another cable from the control panel to the PC). If there are multiple

keypads, they can all be connected together (via the digital bus) while

transferring edited text from the PC, or you can transfer text to each

keypad, one at a time. We recommend using a digital bus splitter (model

BS-84). OLink software also allows editing of the keypad’s system text.

Battery replacement

The system checks the battery status and if discharged it will inform the

end user or the installer. The keypad will continue to work but will also

indicate a low battery. Batteries should be replaced within 2 weeks by a

qualified technician in service mode.

Note: It is strongly recommended to change both batteries together

and with identical types (manufacturer).

Do not put expired batteries in the garbage, but follow local regulations..

Removing the keypad from the system

If the keypad is removed from the system, the control panel indicates this

event. If you want to uninstall the keypad, it must also be erased in the

control panel.

Technical specifications

Power supply 2x lithium batteries type CR123A (3.0V)

Typical battery lifetime approx. 3 years (with a max.of 2 daily activations)

Communication frequency 868 MHz, OASiS protocol

Communication range approx. 100m (open area)

RFID cards Jablotron PC-01 or PC-02 (EM UNIQUE 125kHz)

Door detector input IN = normally closed loop

Dimensions 113 x 121 x 63 mm

Environment according to EN 50131-1 II. internal

Operating temperature range -10 to +40 °C

EN 50131-1, CLC/TS 50131-3, EN 50131-5-3 classification class 2

Can be operated according to ERC REC 70-03

FCC ID VL6JA80F

Jablotron Ltd. hereby declares that the JA-80F is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC

and complies with part 15 of the FCC rules. Operation is subject to the following

two conditions: 1. This device may not cause harmful interference, and 2. This device must

accept any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modifications no expressly approved by Jablotron could void the

user´s authority to operate the equipment. The original of the conformity assessment can

be found at www.jablotron.com, Technical Support

section.

Note: Although this product does not

contain any harmful materials we suggest

you return the product to the dealer or

directly to the producer after use.

: www.

jab

zT+el.: 420 4 983559 99 f: 0ax +42 483 9559 93P

Jab

Czeceph Rublic

OASIS 80

A B C

ABC

GND

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	JA-80F

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-80F stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Sony SNC-DH160 Manual

16 November 2024

Bresser DL-30MP Manual

15 November 2024

D-Link DCS-6500LHV2 Manual

14 November 2024

D-Link DCS-2803KT Manual

13 November 2024

D-Link DCS-2804KT Manual

13 November 2024

D-Link DCS-931L Manual

13 November 2024

D-Link DCS-6100LHV2 Manual

13 November 2024

Philips Series 3000 HSP3800 Manual

13 November 2024

Emos H4060 Manual

13 November 2024

Philips Series 3000 HSP3500 Manual

13 November 2024