Joblotron JA-81F Manual

Joblotron Overvågningskamera JA-81F

Læs nedenfor 📖 manual på dansk for Joblotron JA-81F (1 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 16 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/1

The JA-80F wireless keypad MLH51300 1

The JA-81F wireless keypad

The JA-81F is a component of Jablotron’s OASiS alarm system and is designed to

control and program the system. It has a built-in proximity access card reader and

allows the wiring up of a separate door detector. The battery-powered keypad

communicates wirelessly using OASiS protocol.

Installation

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor. The keypad is for indoor installation only,

typically by the main entrance door. Avoid locating it close to metal objects,

which could shield radio communication.

1. Open the keypad housing (by pressing the tab on the bottom) using a

screwdriver. The tab is also accessible from the front after opening the key

cover.

1. Install the rear housing to the desired location

2. Install the external hard-wired detector (if required) route its cable

through the rear housing and connect to the IN and GND terminals.

3. Enroll the keypad to the control panel (see the control panel

installation manual) as follows:

• Enter enrollment mode in the control panel (if the system does not

have a keypad already, briefly short the reset link on the control panel

main board, or if a keypad is present, then press key 1 in service

mode).

• Install the battery into the keypad to trigger enrollment.

• Exit enrollment mode by pressing the # key.

4. Attach the keypad to the rear housing.

5. Instructions on how to use the keypad can be found in the control panel

operating manual.

Keypad menu

The menu can be entered in Service mode by holding the ? key. Then the

internal keypad menu will be displayed. Using the arrows on keys 1 and 7 you

can scroll through the menu:

Display Key Description

Tamper ON ¾ Disable / Enable the tamper sensor

(only for service purposes)

Door chime ON ¾ Disable / Enable sound when IN triggered

Beeper ON ¾ Disable / Enable system sounds

Brightness  Sets the display brightness 0 - 9

Contrast  Sets the display contrast 0 - 9

Edit text ¾ Entry to keypads text editing

English ¾ Sets English (reload default texts)

Čeština ¾ Other languages ...

To exit the menu, press # (exiting also occurs after 10 seconds’ inactivity).

Notes:

• The menu can be displayed even if the keypad has not been enrolled to the

control panel.

• Each keypad has its own menu, i.e. each keypad in the system can have its

own unique settings.

• The keypad keeps its settings even if its power is disconnected (settings can

only be altered via the keypad menu).

• The menu can also be entered when the ¾ key is kept pressed while the

keypad is being powered-up.

Keypad sleep mode

When battery-powered, the keypad saves energy by turning itself off when the

cover is closed or automatically after 20 seconds of inactivity (15 minutes in service

mode). The keypad is woken up by: opening the keypad‘s flip cover, pressing any

key, or triggering the wired door detector input - see below.

Optional AC adapter

If the keypad is powered by an AC adapter (model: Jablotron DE01-12 for

terminals: +U and GND), it will not turn off after 20 seconds of inactivity. If the

adapter is used, batteries should still be installed. Only turn on the AC adapter

after the keypad unit has been powered up by batteries and the two halves of

the housing are back together.

Note: To comply with EN standards the keypad does not indicate the status of

the alarm system. If desired, the system setting / unsetting status can be

programmed in the control panel to be permanently indicate by the keypad.

Installing a door detector

It is possible to wire up a detector(s) to the keypad. The IN input terminal is

triggered when disconnected from GND. The control panel’s reaction to the IN input

being triggered is a delayed intruder alarm linked to the keypad‘s address. If

desired, another reaction can be programmed in the control panel. The IN input can

indicate a door being permanently open (status reaction). If the IN input is not used

then it must be shorted to GND.

123

ABC

456

789

0 #

OFF

ESC

ABC

OASiS

GND

Note: The lifetime of the battery is reduced proportionally to how frequently the

door detector is triggered and how often and how long the keypad is battery-

powered.

Testing keypad communication

In service mode, the control panel allows you to measure the keypad’s radio

signal strength. To test the keypad signal, trigger either its IN input or its

tamper sensor.

Note: the control panel measures the strength of the signal transmitted by the

keypad. It is impossible to measure the signal strength received by the keypad

from the control panel. If the keypad has lost communication with the control

panel (e.g. if the control panel is damaged) it would display COMM ERROR a

communication error. If you re-power a control panel, which previously worked

with a keypad, and the keypad does not function, then we recommend

disconnecting and re-connecting the keypad batteries.

Controlling the PgX output

The PgX output can be switched ON and OFF by pressing the ON (¾) and

OFF (#) buttons long (for 5 seconds). The function of PgX must be set in the

control panel. A long beep confirms the change of the output’s state.

Keypad text editing

The most convenient way to edit text is to use a PC running OLink software.

To transfer edited text from a PC to the keypad, the keypad (with its batteries

installed) has to be connected either to the OASiS system‘s digital bus (i.e.

one cable from the keypad to the control panel, and another cable from the

control panel to the PC) or directly from the PC. The texts are transferred by

choosing the Save menu in the Texts window in OLink software.

The names can be edited via the keypad in the “Edit Text” menu item – see

the control panel installation manual. The edited text is only stored in the

keypad unit used for editing.

Battery replacement

The system checks the battery status and if discharged it will inform the user or

the installer. The keypad will continue to work but will also indicate a low

battery as well as the backlight being reduced. Batteries should be replaced

within 2 weeks by a qualified technician in service mode. If they are not, the

keypad is switched off when the battery power falls under a critical limit.

Note: Both batteries must be always changed together and with

identical types (manufacturer).

Removing the keypad from the system

If the keypad is removed from the system, the control panel indicates this

event. If you want to uninstall the keypad, it must also be erased in the control

panel.

Technical specifications

Power supply 2x lithium batteries type CR123A (3.0V)

Typical battery lifetime approx. 3 years (with a max.of 2 daily activations)

Communication frequency 868 MHz, OASiS protocol

Communication range approx. 100m (open area)

RFID cards Jablotron PC-01 or PC-02 (EM UNIQUE 125kHz)

Door detector input IN = normally closed loop

Dimensions 120 x 130 x 30 mm

Environment according to EN 50131-1 II. internal

Operating temperature range -10 to +40 °C

EN 50131-1, EN 50131-3, EN 50131-6, EN 50131-5-3 classification 2

Complies with ETSI 300220, ETSI 300330, EN 50130-4,

EN 55022, EN 60950-1

Can be operated according to ERC REC 70-03

JABLOTRON ALARMS a.s. hereby declares that the JA-80F is in compliance

with the essential requirements and other relevant provisions of Directive

1999/5/ECThe original of the conformity assessment can be found at

www.jablotron.com , Technical Support section.

Note: Although this product does not contain any harmful materials we

suggest you return the product to the dealer or directly to the producer

after use.

Produkt Specifikationer

Mærke:	Joblotron
Kategori:	Overvågningskamera
Model:	JA-81F

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-81F stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Overvågningskamera Joblotron Manualer

Joblotron H-915 Manual

13 Maj 2024

Joblotron JA-60 Manual

18 April 2024

Joblotron JA-63E Manual

17 April 2024

Joblotron SP-02 Manual

6 April 2024

Joblotron GS-130 Manual

6 April 2024

Joblotron UC-230 Manual

1 April 2024

Joblotron UC-261 Manual

27 Marts 2024

Joblotron JA-60M Manual

6 Marts 2024

Joblotron JA-80A Manual

6 Marts 2024

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Sony SNC-DH160 Manual

16 November 2024

Bresser DL-30MP Manual

15 November 2024

D-Link DCS-6500LHV2 Manual

14 November 2024

D-Link DCS-2803KT Manual

13 November 2024

D-Link DCS-2804KT Manual

13 November 2024

D-Link DCS-931L Manual

13 November 2024

D-Link DCS-6100LHV2 Manual

13 November 2024

Philips Series 3000 HSP3800 Manual

13 November 2024

Emos H4060 Manual

13 November 2024

Philips Series 3000 HSP3500 Manual

13 November 2024