Joblotron JA-81F-RGB Manual

Joblotron Overvågningskamera JA-81F-RGB

Læs nedenfor 📖 manual på dansk for Joblotron JA-81F-RGB (1 sider) i kategorien Overvågningskamera. Denne guide var nyttig for 28 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/1
The JA-81F-RGB wireless keypad MLH51700 1
The JA-81F-RGB wireless keypad
The JA-81F is a component of Jablotron’s OASiS alarm system and is designed to control
and program the system. The display backlight colour can be set according to your needs.
It has a built-in proximity access card reader and allows the wiring up of a separate door
detector. The battery-powered keypad communicates wirelessly using OASiS protocol.
Installation
Installation shall only be undertaken by technicians holding a certificate issued by
an authorized distributor. The keypad is for indoor installation only, typically by the
main entrance door. Avoid locating it close to metal objects, which could shield radio
communication.
1. Open the keypad housing (by pressing the tab on the bottom) using a
screwdriver. The tab is also accessible from the front after opening the key
cover.
1. Install the rear housing to the desired location
2. Install the external hard-wired detector (if required) route its cable through
the rear housing and connect to the IN and GND terminals.
3. Enroll the keypad to the control panel (see the control panel installation
manual) as follows:
• Enter enrollment mode in the control panel (if the system does not have a
keypad already, briefly short the reset link on the control panel main board,
or if a keypad is present, then press key 1 in service mode).
• Install the battery into the keypad to trigger enrollment.
• Exit enrollment mode by pressing the # key.
4. Attach the keypad to the rear housing.
5. Instructions on how to use the keypad can be found in the control panel
operating manual.
Keypad menu
The menu can be entered in Service mode by holding the ? key. Then the internal
keypad menu will be displayed. Using the arrows on keys 1 and 7 you can scroll
through the menu:
Display Key Description
Tamper ON Disable / Enable the tamper sensor
(only for service purposes)
Door chime ON Disable / Enable sound when IN triggered
Beeper ON Disable / Enable system sounds
Backlight colour  Sets the normal display backlight colour 0 - 7
Warning colour  Sets the warning display backlight colour 0 - 7
Brightness  Sets the display brightness 0 - 9
Contrast  Sets the display contrast 0 - 9
Edit text Entry to keypads text editing
English Sets English (reload default texts)
Čeština other languages ...
To exit the menu, press # (exiting also occurs after 60 seconds’ inactivity).
Notes:
• It is possible to set a different colour backlight as a warning colour for when a fault
is indicated or after an alarm state (warning colour). The user can be visually
informed of the status. If unwanted, please set both colours to the same value.
• The menu can be displayed even if the keypad has not been enrolled to the
control panel.
• Each keypad has its own menu, i.e. each keypad in the system can have its own
unique settings.
• The keypad keeps its settings even if its power is disconnected (settings can only
be altered via the keypad menu).
• The menu can also be entered when the key is kept pressed while the keypad
is being powered-up.
Keypad sleep mode
When battery-powered, the keypad saves energy by turning itself off when the cover is
closed or automatically after 20 seconds of inactivity (15 minutes in service mode). The
keypad is woken up by: opening the keypad‘s flip cover, pressing any key, or triggering
the wired door detector input - see below.
Optional AC adapter
If the keypad is powered by an AC adapter (model: Jablotron DE01-12 for terminals:
+U and GND), it will not turn off after 20 seconds of inactivity. If the adapter is used,
batteries should still be installed. Only turn on the AC adapter after the keypad unit
has been powered up by batteries and the two halves of the housing are back
together.
Note: To comply with EN standards the keypad does not indicate the status of the
alarm system. If desired, the system setting / unsetting status can be programmed in
the control panel to be permanently indicate by the keypad.
Installing a door detector
It is possible to wire up a detector(s) to the keypad. The IN input terminal is triggered when
disconnected from GND. The control panel’s reaction to the IN input being triggered is a
delayed intruder alarm linked to the keypad‘s address. If desired, another reaction can be
programmed in the control panel. The IN input can indicate a door being permanently
open (status reaction). If the IN input is not used then it must be shorted to GND.
1 2 3
ABC
4 5 6
A
7 8 9
ON
0 #
B
?
OFF
ESC
A B C
OASiS
IN
GND
+U
Note: The lifetime of the battery is reduced proportionally to how frequently the door
detector is triggered and how often and how long the keypad is battery-powered.
Testing keypad communication
In service mode, the control panel allows you to measure the keypad’s radio signal
strength. To test the keypad signal, trigger either its IN input or its tamper sensor.
Note: the control panel measures the strength of the signal transmitted by the
keypad. It is impossible to measure the signal strength received by the keypad from
the control panel. If the keypad has lost communication with the control panel (e.g. if
the control panel is damaged) it would display COMM ERROR a communication
error. If you re-power a control panel, which previously worked with a keypad, and
the keypad does not function, then we recommend disconnecting the keypad
batteries for one minute.
Controlling the PgX output
The PgX output can be switched ON and OFF by pressing the ON (
) and OFF (#)
buttons long (for 5 seconds). be set in the control panel. A The function of PgX must
long beep confirms the change of the output’s state.
Keypad text editing
The most convenient way to edit text is to use a PC running OLink software. To
transfer edited text from a PC to the keypad, the keypad (with its batteries installed)
has to be connected eit tal bus (i.e. one cable from the her to the OASiS system‘s digi
keypad to the control panel, and another cable from the control panel to the PC) or
directly from the PC. The texts are transferred by choosing the Save menu in the
Texts window in OLink software.
The names can be edited via the keypad in the “Edit Text” menu item – see the
control panel installation manual. The edited text is only stored in the keypad unit
used for editing.
Battery replacement
The system checks the battery status and if discharged it will inform the user or the
installer. The keypad will continue to work but will also indicate a low battery as well
as the backlight being reduced. Batteries should be replaced within one week by a
qualified technician in service mode. If they are not, the keypad is switched off when
the battery power falls under a critical limit.
Note: Both batteries must be always changed together and with
identical types (manufacturer). Please allow one minute delay before
inserting new batteries.
Removing the keypad from the system
If the keypad is removed from the system, the control panel indicates this event. If
you want to uninstall the keypad, it must also be erased in the control panel.
Technical specifications
Power supply 2x lithium batteries type CR123A (3.0V)
Typical battery lifetime approx. 2 years (2 daily activations and no IN usage)
External power supply 12 V DC
Standby consumption 100mA
Communication frequency 868 MHz, OASiS protocol
Communication range approx. 100m (open area)
RFID cards Jablotron PC-01 or PC-02 (EM UNIQUE 125kHz)
Door detector input IN = normally closed loop
Dimensions 120 x 130 x 30 mm
Environment according to EN 50131-1 II. internal
Operating temperature range -10 to +40 °C
EN 50131-1, EN 50131-3, EN 50131-6, EN 50131-5-3 classification 2
Complies with ETSI 300220, ETSI 300330, EN 50130-4,
EN 55022, EN 60950-1
Can be operated according to ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the JA-80F is in compliance
with the essential requirements and other relevant provisions of Directive
1999/5/ECThe original of the conformity assessment can be found at
www.jablotron.com, Technical Support section.
Note: Although this product does not contain any harmful materials we
suggest you return the product to the dealer or directly to the producer
after use.

Produkt Specifikationer

Mærke: Joblotron
Kategori: Overvågningskamera
Model: JA-81F-RGB

Har du brug for hjælp?

Hvis du har brug for hjælp til Joblotron JA-81F-RGB stil et spørgsmål nedenfor, og andre brugere vil svare dig


Overvågningskamera Joblotron Manualer

Joblotron

Joblotron H-915 Manual

13 Maj 2024
Joblotron

Joblotron JA-60 Manual

18 April 2024
Joblotron

Joblotron JA-63E Manual

17 April 2024
Joblotron

Joblotron SP-02 Manual

6 April 2024
Joblotron

Joblotron GS-130 Manual

6 April 2024
Joblotron

Joblotron UC-230 Manual

1 April 2024
Joblotron

Joblotron UC-261 Manual

27 Marts 2024
Joblotron

Joblotron JA-60M Manual

6 Marts 2024
Joblotron

Joblotron JA-80A Manual

6 Marts 2024
Joblotron

Joblotron JK-16 Manual

6 Januar 2024

Overvågningskamera Manualer

Nyeste Overvågningskamera Manualer

Sony

Sony SNC-DH160 Manual

16 November 2024
Bresser

Bresser DL-30MP Manual

15 November 2024
D-Link

D-Link DCS-6500LHV2 Manual

14 November 2024
D-Link

D-Link DCS-2803KT Manual

13 November 2024
D-Link

D-Link DCS-2804KT Manual

13 November 2024
D-Link

D-Link DCS-931L Manual

13 November 2024
D-Link

D-Link DCS-6100LHV2 Manual

13 November 2024
Philips

Philips Series 3000 HSP3800 Manual

13 November 2024
Emos

Emos H4060 Manual

13 November 2024
Philips

Philips Series 3000 HSP3500 Manual

13 November 2024