Joranalogue Select 2 Manual

Joranalogue Ikke kategoriseret Select 2

Læs gratis den danske manual til Joranalogue Select 2 (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Joranalogue Select 2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

SELECT 2

DUAL GATED CONTROL PRECISION

VOLTAGE PROCESSOR

INTRODUC TIO N

A 'Swiss Army knife' for your modular system,

Select -2 provides two highly accurate gate

controlled voltage processors in 6 HP. These

allow you to create, switch, mute, hold, invert,

attenuate voltages, , offset, add/ and subtractmix

from slow control voltages (CVs) up to audio

frequencies.

Each processor features two signal inputs, with

the left input used by default. A gate on the

'select' input switches to the right signal input

instead. The signal inputs are normalised to the

precision +5 V reference (left) and 0 V (right).

Following the input section is a hold circuit. A

rising edge on the 'hold' input freezes the input

voltage at that moment, until the gate input

goes low again. While most sample/track- -and

hold modules only manage a few seconds,

Select 2 ’s ‘low droop’ design enables it to store a

held voltage accurately for several minutes.

The end of the signal path consists of a gated

polariser/attenuverter. Using the knob, the

voltage at the output can attenuated and/or

inverted: the gain is −1 (inverted) at the minimum

setting, 0 at the centre and 1 (unity gain) at the +

maximum. The polariser can be disabled using

the 'unity' gate input. This unique ability enables

a variety of interesting gate-controlled signal

modulations. Dual-colour LEDs show the output

voltage of each processor.

Finally, if the A output left unsocket is used, the

signal is mixed together with the B output. This

enables signal offsetting, CV mixing, pitch

transposing etc.

CONTENTS

In the Select 2 box, you’ll find:

 Product card, stating serial number and

production batch.

 16- - -to 10 pin Eurorack power cable.

 Mounting hardware: two black M3 x 6 mm

hex screws, two black nylon washers and a

hex key.

 T he Select 2 module itself, in a protective

cotton bag.

If any of these items are missing, please contact

your dealer or support@joranalogue.com.

Produkt Specifikationer

Mærke:	Joranalogue
Kategori:	Ikke kategoriseret
Model:	Select 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Joranalogue Select 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Joranalogue Manualer

Joranalogue Route 4 Manual

16 August 2024

Joranalogue Orbit 3 Manual

14 August 2024

Joranalogue Morph 4 Manual

14 August 2024

Joranalogue Receive 2 Manual

13 August 2024

Joranalogue Fold 6 Manual

13 August 2024

Joranalogue Mix 3 Manual

12 August 2024

Joranalogue Cycle 5 Manual

4 Juli 2024

Joranalogue Compare 2 Manual

5 December 2023

Joranalogue Enhance 2 Manual

22 Oktober 2023

Joranalogue Dim 2 Manual

16 September 2023

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Hikvision DS-QAE1A40G1-VB Manual

23 Oktober 2025

Microchip HV2818 Manual

23 Oktober 2025

Microchip MIC2298 Manual

23 Oktober 2025

Microchip PIC16F630 Manual

23 Oktober 2025

ADATA Valor Air Mera Edition Manual

23 Oktober 2025

Vestil RSH-108-EF-A Manual

21 Oktober 2025

Hikvision DS-3E1106P-EI Manual

21 Oktober 2025

Dasqua 5121-1101 Manual

21 Oktober 2025

Vestil HCH-1-10 Manual

21 Oktober 2025

Rowenta x Karl Lagerfeld Curls Forever CF311L Manual

21 Oktober 2025