JVC CA-UXG300 Manual

JVC Hi-Fi system CA-UXG300

Læs nedenfor 📖 manual på dansk for JVC CA-UXG300 (2 sider) i kategorien Hi-Fi system. Denne guide var nyttig for 18 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of

10 cm or more.

INSTRUCTIONS

GVT0241-001A[B]

0108WMKMDWJMM

2 4

Connections

Basic and Common Operations

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If

the plug fitted is not suitable for the power points in your

home or the cable is too short to reach a power point,

then obtain an appropriate safety approved extension lead

or consult your dealer.

BE SURE to replace the fuse only with an identical

approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove

the fuse and dispose of the plug immediately, to avoid a

possible shock hazard by inadvertent connection to the

mains supply.

If this product is not supplied fitted with a mains plug then

follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is

marked with the letter E or by the safety earth symbol or

coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in

accordance with the following code:

Blue: Neutral

Brown: Live

As these colours may not correspond with the coloured

markings identifying the terminals in your plug proceed

as follows:

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or coloured

red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Warnings, Cautions and Others

CAUTION: (Standby/on) button!

Disconnect the mains plug to shut the power off completely

(the STANDBY lamp goes off). When installing the apparatus,

ensure that the plug is easily accessible. The (Standby/on)

button in any position does not disconnect the mains line.

• When the System is on standby, the STANDBY lamp lights

red.

• When the System is turned on, the STANDBY lamp goes

off.

The power can be remote controlled.

CAUTION:

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

Supplied Accessories

After unpacking, check to be sure that you have all the

following items.

• Remote control, RM-SUXG300R (× 1)

• Lithium coin battery CR2025 (× 1)

– The battery has been installed when shipped from the

factory.

• AM loop antenna (× 1)

• FM antenna (× 1)

• Core filter (× 1), see page 7 for details

If anything is missing, consult your dealer immediately.

Prepare the Remote Control

When you use the remote control for the first time, pull out

the insulation sheet.

To Replace the Battery in the Remote Control

NOTES:

• Store the battery in a place where children cannot reach. If

a child accidentally swallows the battery, consult a doctor

immediately.

• To prevent the battery from over-heating, cracking, or starting

a fire:

– Do not recharge, short, disassemble or heat the battery or

dispose of it in a fire.

– Do not leave the battery with other metallic materials.

– Wrap the battery with tape and insulate when throwing

away or saving it.

– Do not poke the battery with tweezers or similar tools.

• Dispose of battery in the proper manner, according to federal,

state, and local regulations.

• The batteries (battery pack or batteries installed) shall not be

exposed to excessive heat source such as sunshine, fire or the

like.

Basic Disc/USB Mass Storage Class Device Operations

To Press Indication/Result

Play back the disc • Current track number and elapsed playing

time appear.

For MP3/WMA files: Before current track

number and elapsed playing time appear, the

tag information appears if it is recorded.

• During playback, press again to pause.

Play back the USB

mass storage class

device

Stop playback • While playback is stopped, total track number

and total playing time (for MP3/WMA files,

group number and track number) appear.

Select a track Select the next tracks.

To go back to the beginning of the current or

previous tracks.

Select a group

(MP3/WMA only)

Select the next groups.

Select the previous groups.

Forward search/

Reverse search

Press and hold to fast-forward the track during

playback.

To stop searching, release the button.

Press and hold to fast-reverse the track during

playback.

To stop searching, release the button.

NOTES:

• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or

“NO USB” appears on the main display.

• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,

“NO PLAY” appears on the main display.

Getting Started Playing Back a Disc/USB Mass Storage Class Device

CAUTION:

• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth,

etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted candles, on the apparatus.

• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of

these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases,

shall be placed on the apparatus.

• Excessive sound pressure from earphones or headphones can cause hearing loss.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. Do not open the top cover or cabinet. There CAUTION:

are no user serviceable parts inside the unit; leave all

servicing to qualified service personnel.

3. Visible and/or invisible class 1M laser radiation CAUTION:

when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED

INSIDE THE UNIT.

Dear Customer,

This apparatus is in conformance with the valid European

directives and standards regarding electromagnetic

compatibility and electrical safety.

European representative of Victor Company of Japan,

Limited is:

JVC Technology Centre Europe GmbH

Company name changed in:

JVC Technical Services Europe GmbH

Postfach 10 05 52

61145 Friedberg

Germany

Precautions

Notes on the power cord

• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet.

• When unplugging the System from the wall outlet, always pull the plug, not the power cord.

• Do not handle the power cord with wet hands.

• Disconnect the power cord before cleaning the System or moving the System.

• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.

• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.

Avoid moisture, water, dust, and high temperatures

• Do not place the System in moist or dusty places.

• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using

the System in this state may cause a fire or electrical shock.

• Do not expose the System to direct sunlight or place it near a heating device.

Notes on installation

• Select a place which is level, dry and neither too hot nor too cold—between 5˚C and 35˚C.

• Do not install the System in a place subject to vibrations.

• Do not put heavy objects on the System.

To prevent malfunction or damage of the System

• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.

• Do not block the vents.

There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.

MICRO COMPONENT SYSTEM

UX-G300

—Consists of CA-UXG300 and SP-UXG300

This System can play back...

– CD.

– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files

in ISO 9660 format.

– USB mass storage class device containing MP3/WMA files.

• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.

Loading a Disc (on the System only)

1Press to open the disc tray.

2• When using an 8 cm disc, place it on the inner

circle of the disc tray.

3Press to close the disc tray.

Connecting a USB Mass Storage Class Device

You can connect a USB mass storage class device such as a USB flash memory

device, MP3 player, multimedia card reader, etc. to the System.

NOTES:

• When connecting with a USB cable, use the USB 2.0 cable whose length is less than

1 m.

• USB mass storage class device is charged through the USB MEMORY terminal when

the System is turned on and the source is “USB.”

• You cannot connect a computer to the USB MEMORY terminal of the System.

• Do not disconnect the USB mass storage class device when the System is turned on. It

may cause malfunction of both this System and the device.

• Noise and static electricity may stop the USB mass storage class device sound. In this

case, disconnect and connect the USB mass storage class device again after turning

off the System.

Prohibiting Disc Ejection (on the System only)

You can lock the disc tray so that no one can eject the loaded disc.

• This is possible while the System is on standby.

To cancel the prohibition, repeat the same procedure.

USB cable (not supplied)

Playing Repeatedly—Repeat Play

1Press repeatedly to specify the repeat mode as follows:

REP TRK: Repeats the current (or specified) track. [ ]

REP GRP: Repeats all tracks in the current group (MP3/WMA

only). [ ]

REP ALL: Repeats all tracks. [ ALL ]

REP OFF: Normal playback

2or

Programming the Playing Order—Program Play

1During stops, press until the PRGM (program) indicator lights

up before playing.

• For MP3/WMA files: Select a group number, then a track

number.

• For CD: Select a track number.

3Press to program the selected group/track.

4Repeat steps 2 3 and to program other tracks you want.

• If you try to program a 51st track, “FULL” will appear.

5The tracks are played back in the programmed order.

Operations for Program Play (while not playing)

• To check the programmed contents, press or .4 ¢

• To add tracks, repeat steps and above.2 3

• To erase the last programmed track, press CANCEL.

• To erase the entire program, press and hold CANCEL for about 2 seconds.

• To exit from program play, press MODE.

– The stored program is kept.

Playing at Random—Random Play

1Press until the RND (random) indicator lights up before you start

playback.

2or Playback starts in random order.

Random Play ends when all tracks are played back.

Operations for Random Play

• To skip a track, press .¢

• To go back to the beginning of the current track, press .4

• To exit from random play, press MODE while playback is stopped.

Thank you for purchasing a JVC product.

Front view Side view

Information for Users on Disposal of Old

Equipment

[European Union only]

This symbol indicates that the product

with this symbol should not be disposed

as general household waste. If you want to

dispose of this equipment, please do not

use the ordinary dust bin! There is a separate

collection System for these products.

To Press Indication/Result

System Remote

Turn on or off

(standby) the power

The STANDBY lamp on the System turns off/on.

Select a source See “Playing Back a Disc/USB Mass Storage Class

Device” on page 4.

Press repeatedly to select “FM” or “AM.”

• For “FM/AM,” see “Listening to FM and AM

Broadcasts” on page 5.

See “Listening to Digital Audio Player” on page 6.

Adjust the volume Adjustable range: Level 0 (“VOL MIN”) to level 40

(“VOL MAX”).

Drop the volume in

a moment —To restore the volume, press again, or adjust the

volume level.

Activate the EALA

surround mode —

The indicator lights up.

To cancel this function, press repeatedly until

indicator lights off.

Emphasize the

sound (Sound Turbo

function)

The S.TURBO indicator lights up.

To cancel this function, press again.

Reinforce the bass

sound (Active Hyper

Bass Pro function) —

Press and hold until the AHB indicator lights up.

• When Sound Turbo function is activated (see above),

this function cannot be activated.

To cancel this function, press and hold again when

Sound Turbo function is deactivated.

Adjust the tone

(Bass/Treble)

—

Press once for adjusting the bass level; twice for treble

level, then, press VOLUME +/–.

Adjustable range: –3 to +3.

Change the display

brightness —

Press when the System is turned on.

To cancel this function, press again.

Change the display

information (Clock

and Source)

—

For setting the clock, see “Setting the Clock and Using

Timers” on page 6.

• Not applicable for FM.

Set the Save Mode

—

Press when the System is on standby.

Setting the save mode allows you to reduce power

consumption by turning the display off while on

standby.

To cancel this function, press again when the System

is on standby.

NOTE:

DO NOT turn off (standby) the System with the volume set to an extremely high level;

otherwise, the sudden blast of sound can damage your hearing, speakers and/or

headphones when you turn on the System or start playback.

To a wall outlet

Plug the AC power cord only after all connections are complete.

Rear view

Outdoor FM antenna

(not supplied)

Disconnect the supplied FM antenna, and connect to

an outdoor FM antenna using a 75 Ω wire with coaxial

type connector (IEC or DIN45325).

FM antenna (supplied)

AM loop antenna (supplied)

Turn it until the best reception

is obtained.

RESUME Play (For MP3/WMA only)

When you stop the playback by one of the following operations, this System

stores the beginning of the stopped track on the disc or USB mass storage class

device.

– Pressing 7 once

– Changing the source

When you start playback again, playback starts from the stored position.

To clear the stored position, open the disc tray or disconnect the USB mass

storage class device.

• When you clear the stored position and start playback, playback starts from the

beginning of the first track

NOTE:

This function does not work in Program Play and Random Play.

The following operations are explained using the remote control, unless

mentioned otherwise. However, if the System has the same or similar button

names, they can also be used for the operations.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

NOTES:

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas

away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.

• Make sure both the speakers are connected correctly and firmly.

• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).

• DO NOT connect more than one speaker to each terminal.

• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.

Do not connect the AC power cord until all other connections have been made.

To connect the FM antenna (supplied)

Extend it so that you can obtain the best reception.

For better FM reception

To connect the AM loop antenna (supplied) To assemble the AM loop antenna

To connect the speaker cords

Using Headphones

Be sure to turn down the volume before connecting or putting on the headphones.

• Connecting the headphones will deactivate the speakers.

• Sound adjustments also affect the sound through the headphones.

STANDBY lamp

Point at the remote sensor on the front panel.

(The operating range is approx. 7 m.)

PHONES jack

Stereo mini plug cord

Front view

Lithium coin battery

(product number: CR2025)

Insulation sheet

Press and hold

Insert

Release

Red

Black From left

speaker

From right

speaker

How to cancel the demonstration

Press and hold DEMO button while on standby. (Refer to the attached “Information

about the demonstration function.”)

Produkt Specifikationer

Mærke:	JVC
Kategori:	Hi-Fi system
Model:	CA-UXG300

Har du brug for hjælp?

Hvis du har brug for hjælp til JVC CA-UXG300 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system JVC Manualer

JVC CA-MXJ750R Manual

31 August 2024

JVC RD-E761 Manual

28 August 2024

JVC UX-F227B-DAB Manual

5 August 2024

JVC FS-900 Manual

31 Juli 2024

JVC CA-MXJ550R Manual

30 Juli 2024

30 Juli 2024

29 Juli 2024

29 Juli 2024

26 Juli 2024

25 Juli 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

Honor Earbuds X6 Manual

23 November 2024

Alba ICS105 Manual

16 November 2024

Korg Nu 1 Manual

15 November 2024

Kenwood UD-F5 Manual

15 November 2024

Krüger&Matz KM1961 Manual

15 November 2024

Auna VCP-191 Manual

15 November 2024

Denon CEOL N-8 Manual

15 November 2024

Samsung MAX-DC20900 Manual

10 November 2024

Samsung MAX-X65 Manual

10 November 2024

Samsung MAX-DT95 Manual

10 November 2024