JVC SP-UXG38 Manual

JVC Hi-Fi system SP-UXG38

Læs nedenfor 📖 manual på dansk for JVC SP-UXG38 (4 sider) i kategorien Hi-Fi system. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

To connect the speaker cords

Make sure the both speakers are connected correctly and

firmly.

• Before connecting the speaker cords, twist and pull the

insulation coat off and remove.

When connecting the speaker cords, match the polarity of

the speaker terminals: gray cord to (+) and gray cord with

black stripe to (–).

2 4

Connections

Do not connect the AC power cord until all other connections have been made.

Basic and Common Operations

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If

the plug fitted is not suitable for the power points in your

home or the cable is too short to reach a power point,

then obtain an appropriate safety approved extension lead

or consult your dealer.

BE SURE to replace the fuse only with an identical

approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove

the fuse and dispose of the plug immediately, to avoid a

possible shock hazard by inadvertent connection to the

mains supply.

If this product is not supplied fitted with a mains plug then

follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is

marked with the letter E or by the safety earth symbol or

coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in

accordance with the following code:

Blue: Neutral

Brown: Live

As these colours may not correspond with the coloured

markings identifying the terminals in your plug proceed

as follows:

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or coloured

red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Warnings, Cautions and Others

Caution — button!

Disconnect the mains plug to shut the power off completely

(the STANDBY lamp goes off ). When installing the apparatus,

ensure that the plug is easily accessible. The button in

any position does not disconnect the mains line.

• When the system is on standby, the STANDBY lamp lights

red.

• When the system is turned on, the STANDBY lamp goes off.

The power can be remote controlled.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

Supplied Accessories

After unpacking, check to be sure that you have all the

following items. The number in parentheses indicates the

quantity of each piece supplied.

• Remote control (x 1)

• Lithium coin battery CR2025 (x 1) (The battery has been

installed when shipped from the factory.)

• AM loop antenna (x 1)

• FM antenna (x 1)

• Core filter (x 1)

If anything is missing, consult your dealer immediately.

To a wall outlet

Plug the AC power cord only after all

connections are complete.

AM loop antenna (supplied)

Turn it until the best reception

is obtained.

To assemble the

AM loop antenna

To connect the AM loop antenna

NOTES

• DO NOT connect more than one speaker to each terminal.

• DO NOT allow the conductor of the speaker cords to be in

touch with the metallic parts of the System.

NOTES

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the

antennas away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.

• If the cords are covered with vinyl, remove the vinyl to expose the tip of the cord by twisting the vinyl.

Basic Disc/USB Mass Storage Class Device Operations

Press

On the

System

On the

remote

Play back the disc • Current track number and elapsed playing time appear on the

main display.

For MP3/WMA files: Before current track number and elapsed

playing time appear, the tag information is scrolled if it is recorded.

• During playback, press again to pause.

Play back the USB

mass storage

class device

Stop playback

• While playback is stopped, total track number and total playing

time (for MP3/WMA files, group number and track number)

appear on the main display.

Select a track

Press to select the next tracks.

Press to go back to the beginning of the current or previous tracks.

Select a group

(MP3/WMA only)

— Press to select the next groups while playback is stopped.

— Press to select the previous groups while playback is stopped.

Forward search/

Reverse search

—Press once or twice to fast-forward the track during playback.

To stop searching, press .6

—Press once or twice to fast-reverse the track during playback.

To stop searching, press .6

NOTES

• If no disc is inserted, “NO DISC” appears on the main display.

• If no USB mass storage class device is connected, “NO USB” appears on the main display.

• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device, “NO FILE” appears on the

main display.

Outdoor FM antenna

(not supplied)

For better FM reception

FM antenna (supplied)

Extend it so that you can obtain the best reception.

Getting Started Playing Back a Disc/USB Mass Storage Class Device

Disconnect the supplied FM antenna,

and connect to an outdoor FM antenna

using a 75 Ω wire with coaxial type

connector (IEC or DIN45325).

CAUTION:

• Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper

or cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted

candles, on the apparatus.

• When discarding batteries, environmental problems

must be considered and local rules or laws governing the

disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping

or splashing and that no objects filled with liquids, such

as vases, shall be placed on the apparatus.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user

serviceable parts inside the unit; leave all servicing to

qualified service personnel.

3. Visible and/or invisible class 1M laser radiation CAUTION:

when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED

INSIDE THE UNIT.

NOTES

• Store the battery in a place where children cannot reach. If

a child accidentally swallows the battery, consult a doctor

immediately.

• Do not recharge, short, disassemble or heat the battery or

dispose of it in a fire. Doing any of these things may cause

the battery to give off heat, crack, or start a fire.

• Do not leave the battery with other metallic materials.

Doing this may cause the battery to give off heat, crack, or

start a fire.

• When throwing away or saving the battery, wrap it in tape

and insulate; otherwise, the battery may start to give off

heat, crack, or start a fire.

• Do not poke the battery with tweezers or similar tools.

Doing this may cause the battery to give off heat, crack, or

start a fire.

• Dispose of battery in the proper manner, according to

federal, state, and local regulations.

• The batteries (battery pack or batteries installed ) shall not

be exposed to excessive heat source such as sunshine, fire

or the like.

CAUTION:

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Dear Customer,

This apparatus is in conformance with the valid European

directives and standards regarding electromagnetic

compatibility and electrical safety.

European representative of Victor Company of Japan,

Limited is:

JVC Technology Centre Europe GmbH

Postfach 10 05 52

61145 Friedberg

Germany

Precautions

Notes on the power cord

• When you are away on travel or otherwise for an extended period of time, remove the plug from the wall outlet. A small

amount of power (3.0 W) is always consumed while the power cord is connected to the wall outlet.

• When unplugging the System from the wall outlet, always pull the plug, not the power cord.

• Do not handle the power cord with wet hands.

• Disconnect the power cord before cleaning the System or moving the System.

• Do not alter, twist or pull the power cord, or put anything heavy on it, which may cause fire, electric shock, or other accidents.

• If the cord is damaged, consult a dealer and have the power cord replaced with a new one.

Avoid moisture, water, dust, and high temperatures

• Do not place the System in moist or dusty places.

• If water gets inside the System, turn off the power and remove the plug from the wall outlet, then consult your dealer. Using

the System in this state may cause a fire or electrical shock.

• Do not expose the System to direct sunlight or place it near a heating device.

Notes on installation

• Select a place which is level, dry and neither too hot nor too cold between 5˚C and 35˚C.

• Do not install the System in a place subject to vibrations.

• Do not put heavy objects on the System.

To prevent malfunction or damage of the System

• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the System.

• Do not block the vents.

There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult

your dealer.

MICRO COMPONENT SYSTEM

UX-G37

—Consists of CA-UXG37 and SP-UXG38

UX-G38

—Consists of CA-UXG38 and SP-UXG38

INSTRUCTIONS

GNT0080-001A[B]

0107JSKMDWJEM

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of

10 cm or more.

Front view Side view

Information for Users on Disposal of Old Equipment

[European Union only]

This symbol indicates that the product with this symbol should not be disposed as general household

waste. If you want to dispose of this equipment, please do not use the ordinary dust bin! There is a separate

collection System for these products.

This System can play back...

– CD.

– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/

WMA files in ISO 9660 format.

– USB mass storage class device which contains MP3/WMA files.

• When playing back an MP3 or WMA track, MP3 or WMA indicator lights

on the display.

Loading a Disc

Press to open the disc tray.

2• When using an 8 cm disc, place it on

the inner circle of the disc tray.

Press to close the disc tray.

Connecting a USB Mass Storage Class Device

You can connect a USB mass storage class device such as a USB flash

memory device, MP3 player, multimedia card reader, etc. to the System.

NOTES

• When connecting with a USB cable, use the cable whose length is less

than 1 m.

• USB mass storage class device is charged through the USB MEMORY

terminal when the System is turned on and the source is “USB.”

• You cannot connect a computer to the USB MEMORY terminal of the

System.

• Do not disconnect the USB mass storage class device when the System is

turned on. It may cause malfunction of both this System and the device.

• Noise and static electricity may stop the USB mass storage class device

sound. In this case, disconnect and connect the USB mass storage class

device again after turning off the System.

Turning Off the System Automatically

—AUTO STANDBY function

Press and hold until the A.STBY indicator lights on the display.

• The A.STBY indicator starts flashing after playback stops.

If no operation is done for about 3 minutes, the System

turns off.

To cancel this function, press and hold again.

Prohibiting Disc Ejection

You can lock the disc tray so that no one can eject the loaded disc.

• This is possible while the System is on standby.

On the System only

Press and hold

To cancel the prohibition, repeat the

same procedure.

Play mode indicators

(See page 4.)

Radio Data System indicators (See page 5.)

QPL indicator

(See page 6.)

Main Display

A.STBY (Auto Standby) indicator (See page 4.)

AHB indicator (See the left table.)

Using Headphones

Be sure to turn down the volume before connecting or putting on

the headphones.

• Connecting the headphones will deactivate the speakers.

• Sound adjustments also affect the sound through the headphones.

Operating on the Remote Control

To Pre ss

Turn on or off

(standby) the power

The STANDBY lamp on the System turns

off/on.

Select a source*

See “Playing Back a Disc/USB Mass Storage

Class Device” on page 4.

Press repeatedly to select “FM,” “AM,” or “LINE.”

• For “FM/AM,” see “Listening to FM and AM

Broadcasts” on page 5.

• For “LINE,” see “Listening to Digital Audio

Player” on page 6.

Adjust the volume You can adjust the volume level from level 0

(“VOL MIN”) to level 31 (“VOL MAX”).

Drop the volume in a

moment

To restore the volume, press again, or adjust

the volume level.

Emphasize the sound

(Sound Turbo

function)

The S.TURBO indicator lights on the display.

To cancel this function, press again.

Reinforce the bass

sound (Active Hyper

Bass Pro function)

Press and hold until the AHB indicator lights

on the display.

• When Sound Turbo function is activated (see

above), this function cannot be activated.

To cancel this function, press and hold again.

Display Information

To Pre ss

Adjust the tone (Bass/

Treble)

• Once: for the bass level

• Twice: for the treble level

Then, press VOLUME + to increase the level or

press VOLUME – to decrease it.

• You can adjust the bass and/or treble level

from –3 to +3.

Changing the display

information (Clock

and Source)

Press briefly (not applicable for FM mode).

For setting the clock, see “Setting the Clock

and Daily Timer” on page 6.

Turn off the System by

using the sleep timer

Press repeatedly to specify the time (in

minutes) as follows (The SLEEP indicator lights

on the display):

• To check the remaining time to turn off after

setting the sleep timer, press once.

* The corresponding source indicator lights on the display (except when selecting

“LINE”).

NOTE

DO NOT turn off (standby) the System with the volume set to an extremely high level;

otherwise, the sudden blast of sound can damage your hearing, speakers and/or

headphones when you turn on the System or start playback.

RESUME indicator (See page 4.)

Source indicators (See the left table.)

Timer mode indicators (See page 6.)

SLEEP indicator (See the left table.)

File type indicators (See page 4.)

Programming the Playing Order—

Program Play (not Applicable for MP3/

WMA Discs)

1Press repeatedly until the PRGM

(program) indicator lights on the

display before playback.

2or Select a track number to program.

3Press to program the selected

track.

4Repeat steps and 2 3 to program other tracks you want.

• If you try to program a 33rd track, “FULL” will appear on

the main display.

The tracks are played back in the

programmed order.

To Operate on the Program Play Mode

To Pre ss

Check the

programmed

contents or Press while playback is

stopped.

Add tracks Repeat steps 2 3 and above while playback

is stopped.

Erase tracks

1Press UP or DOWN to select the track you

want to erase while playback is stopped.

2Press to erase the track.

Erase the

entire program

Press while playback is

stopped.

Exit from

program play

Press twice while playback is

stopped.

• The stored program is

erased.

Playing at Random—Random Play

1Press repeatedly until the RND

(random) indicator lights on the

display before you start playback.

Playback starts in random order.

Random Play ends when all

tracks are played back.

To Operate on the Random Play Mode

To Pre ss

Skip a track Press to skip the current track.

Go back to the

beginning of

the current

track

Press to go back to the

beginning of the current track.

Exit from

random play

Press once while playback is

stopped.

Canceled

USB cable (not supplied)

Front view

FM reception

indicators

(See page 5.)

Source indicators (See the left table.)

Playing Repeatedly—Repeat Play

1Press repeatedly before you start playback to specify the repeat mode

as follows:

REP 1 Repeats the current (or specified) track.

REP GRP Repeats all tracks in the current group (MP3/

WMA only).

ALL REP ALL Repeats all tracks.

REP OFF Normal playback

S.TURBO (Sound Turbo) indicator (See the left table.)

Point at the remote

sensor on the front panel.

(The operating range is

approx. 7 m.)

STANDBY lamp

PHONES jack

Stereo mini plug cord

Operating on the System

To Pre ss

Turn on or off (standby)

the power The STANDBY lamp on the System turns off/on.

Changing the display

brightness

Press when the System is turned on.

To cancel this function, press again.

Set the Save mode

Press and hold for more than 2 seconds when the System is on standby.

• Setting the Save mode allows you to reduce power consumption by

turning the display off while on standby.

To cancel this function, press and hold for more than 2 seconds again.

Emphasize the sound

(Sound Turbo function) To cancel this function, press again.

Select a source*

See “Playing Back a Disc/USB Mass Storage Class Device” on page 4.

See “Listening to FM and AM Broadcasts” on page 5.

See “Listening to Digital Audio Player” on page 6.

Adjust the volume You can adjust the volume level from level 0 (“VOL MIN”) to level 31

(“VOL MAX”).

Thank you for purchasing a JVC product.

Prepare the Remote Control

When you use the remote control for

the first time, pull out the insulation

sheet.

To Replace the Battery in the Remote Control

Insert the battery into the remote control by matching the

polarity (+ and –) correctly.

Insulation sheet

Lithium coin battery

(product number: CR2025)

Attaching the Core Filter

Attach the provided core filter to the power cord, then the

core filter reduces interference.

Stopper

Release the stopper of the core

filter.

2Run the power cord through the

core filter, leaving approx. 5 cm

between the rear of the unit and

the core filter.

Wind firmly the power cord twice

inside the cutout of the core filter

as shown in the illustration.

Close the core filter until you hear

a clicking sound.

NOTE

Do not damage the power cord by applying excessive

power when winding.

The illustration of the unit

above is UX-G38.

• UX-G37 is in black color.

RESUME Play

When you stop the playback by one of the following

operations, this System stores the beginning of the

stopped track on the disc or stores the stopped

position of the file on the USB mass storage class

device.

– Pressing 7 once (The RESUME indicator lights on the

display.)

– Changing the source

– Turning off the System

When you start playback again, playback starts from

the stored position.

To clear the stored position, press while playback 7

is stopped.

• Opening the disc tray or disconnecting the USB

mass storage class device also clears the stored

position.

• When you clear the stored position and start

playback, playback starts...

– For disc: From the beginning of the first track

– For USB mass storage class device: From the

beginning of the current file

If you disconnect the USB mass storage class

device, connect it again, and start playback,

playback starts from the beginning of the first file.

NOTE

This function does not work in program play and

random play (see the right tables).

CAUTION:

Excessive sound pressure from earphones or headphones

can cause hearing loss.

Produkt Specifikationer

Mærke:	JVC
Kategori:	Hi-Fi system
Model:	SP-UXG38

Har du brug for hjælp?

Hvis du har brug for hjælp til JVC SP-UXG38 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system JVC Manualer

JVC CA-MXJ750R Manual

31 August 2024

JVC RD-E761 Manual

28 August 2024

JVC UX-F227B-DAB Manual

5 August 2024

JVC FS-900 Manual

31 Juli 2024

JVC CA-MXJ550R Manual

30 Juli 2024

30 Juli 2024

29 Juli 2024

29 Juli 2024

26 Juli 2024

25 Juli 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

Alba ICS105 Manual

16 November 2024

Korg Nu 1 Manual

15 November 2024

Kenwood UD-F5 Manual

15 November 2024

Krüger&Matz KM1961 Manual

15 November 2024

Auna VCP-191 Manual

15 November 2024

Denon CEOL N-8 Manual

15 November 2024

Samsung MAX-DC20900 Manual

10 November 2024

Samsung MAX-X65 Manual

10 November 2024

Samsung MAX-DT95 Manual

10 November 2024

Samsung MAX-DA67 Manual

10 November 2024