JVC UX-G650 Manual

JVC Hi-Fi system UX-G650

Læs nedenfor 📖 manual på dansk for JVC UX-G650 (4 sider) i kategorien Hi-Fi system. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/4

CAUTION: Proper Ventilation

To avoid risk of electric shock and fire, and to prevent

damage, locate the apparatus as follows:

1. Front: No obstructions and open spacing.

2. Sides/Top/Back: No obstructions should be placed in the

areas shown by the dimensions below.

3. Bottom: Place on the level surface. Maintain an adequate

air path for ventilation by placing on a stand with a

height of 10 cm or more.

INSTRUCTIONS

GVT0253-001A[B]

0508WMKMDWJMM

2 4

Connections

Basic and Common Operations

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If

the plug fitted is not suitable for the power points in your

home or the cable is too short to reach a power point,

then obtain an appropriate safety approved extension lead

or consult your dealer.

BE SURE to replace the fuse only with an identical

approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove

the fuse and dispose of the plug immediately, to avoid a

possible shock hazard by inadvertent connection to the

mains supply.

If this product is not supplied fitted with a mains plug then

follow the instructions given below:

IMPORTANT:

DO NOT make any connection to the terminal which is

marked with the letter E or by the safety earth symbol or

coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in

accordance with the following code:

Blue: Neutral

Brown: Live

As these colours may not correspond with the coloured

markings identifying the terminals in your plug proceed

as follows:

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or coloured

black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or coloured

red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

Warnings, Cautions and Others

CAUTION

The button in any position does not disconnect the mains

line.

Disconnect the mains plug to shut the power off completely

(the STANDBY lamp goes off).

The MAINS plug or an appliance coupler is used as the

disconnect device, the disconnect device shall remain readily

operable.

• When the System is on standby, the STANDBY lamp lights

red.

• When the System is turned on, the STANDBY lamp goes

off.

The power can be remote controlled.

CAUTION:

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

Supplied Accessories

After unpacking, check to be sure that you have all the

following items.

• Remote control, RM-SUXG650R (× 1)

• AM loop antenna (× 1)

• FM antenna (× 1)

• Batteries (× 2)

• Core filter (× 1), See page 8 for details.

If anything is missing, consult your dealer immediately.

Prepare the Remote Control

Insert the battery into the remote control by matching the

polarity ( + and –) correctly.

If the range or effectiveness of the remote control decreases,

replace both batteries.

Basic Disc/USB Mass Storage Class Device Operations

To Press Indication/Result

Play back the disc • Current track number and elapsed playing

time appear.

For MP3/WMA/WAV files: Before current track

number and elapsed playing time appear, the

tag information appears if it is recorded.

• During playback, press again to pause.

Play back the USB

mass storage class

device

Stop playback • While playback is stopped, total track number

and total playing time (for MP3/WMA/WAV

files, group number and track number)

appear.

Select a track Select the next tracks.

To go back to the beginning of the current or

previous tracks.

Select a track

directly

Examples:

To select 5, press 5.

To select 10, press 10.

To select 15, press 10, 1, then 5.h

To select 30, press 10, 3, then 0.h

To select 125, press 10, 10, 1, 2, then 5.h h

Select a group

(MP3/WMA/WAV

only)

Select the next groups.

Select the previous groups.

Forward search/

Reverse search

Press and hold to fast-forward the track during

playback.

To stop searching, release the button.

Press and hold to fast-reverse the track during

playback.

To stop searching, release the button.

NOTES:

• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or

“NO USB” appears on the main display.

• If MP3/WMA/WAV files are not recorded on the disc or in the USB mass storage class

device, “NO PLAY” appears on the main display.

Getting Started Playing Back a Disc/USB Mass Storage Class Device

CAUTION:

•

Do not block the ventilation openings or holes. (If the

ventilation openings or holes are blocked by a newspaper or

cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted

candles, on the apparatus.

• When discarding batteries, environmental problems

must be considered and local rules or laws governing the

disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping

or splashing and that no objects filled with liquids, such as

vases, shall be placed on the apparatus.

• Excessive sound pressure from earphones or headphones

can cause hearing loss.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. Do not open the top cover or cabinet. There CAUTION:

are no user serviceable parts inside the unit; leave all

servicing to qualified service personnel.

3. Visible and/or invisible class 1M laser radiation CAUTION:

when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED

INSIDE THE UNIT.

Dear Customer,

This apparatus is in conformance with the valid European

directives and standards regarding electromagnetic

compatibility and electrical safety.

European representative of Victor Company of Japan,

Limited is:

JVC Technical Services Europe GmbH

Postfach 10 05 04

61145 Friedberg

Germany

Precautions

Notes on the power cord

• When you are away on travel or otherwise for an extended

period of time, remove the plug from the wall outlet.

• When unplugging the System from the wall outlet, always

pull the plug, not the power cord.

• Do not handle the power cord with wet hands.

• Disconnect the power cord before cleaning the System or

moving the System.

•

Do not alter, twist or pull the power cord, or put anything heavy

on it, which may cause fire, electric shock, or other accidents.

• If the cord is damaged, consult a dealer and have the power

cord replaced with a new one.

Avoid moisture, water, dust, and high temperatures

• Do not place the System in moist or dusty places.

•

If water gets inside the System, turn off the power and remove

the plug from the wall outlet, then consult your dealer. Using

the System in this state may cause a fire or electrical shock.

• Do not expose the System to direct sunlight or place it near

a heating device.

Notes on installation

• Select a place which is level, dry and neither too hot nor too

cold—between 5˚C and 35˚C.

• Do not install the System in a place subject to vibrations.

• Do not put heavy objects on the System.

To prevent malfunction or damage of the System

• Do not insert any metallic objects, such as wires, hairpins,

coins, etc. into the System.

• Do not block the vents.

There are no user-serviceable parts inside. If anything

goes wrong, unplug the power cord and consult your

dealer.

MICRO COMPONENT SYSTEM

UX-G650

—Consists of CA-UXG650 and SP-UXG650

This System can play back...

– CD.

– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA/WAV

files in ISO 9660 format.

– DVD-ROM recorded MP3/WMA/WAV files in UDF-Bridge format.

– USB mass storage class device containing MP3/WMA/WAV files.

• When playing back an MP3 or WMA track, corresponding indicator lights up.

Loading a Disc (on the System only)

1Press to open the disc tray.

2• When using an 8 cm disc, place it on the inner

circle of the disc tray.

3Press to close the disc tray.

Connecting a USB Mass Storage Class Device

You can connect a USB mass storage class device such as a USB flash memory

device, MP3 player, multimedia card reader, etc. to the System.

NOTES:

• When connecting with a USB cable, use the USB 2.0 cable whose length is less than

1 m.

• USB mass storage class device is charged through the USB MEMORY REC/PLAY

terminal when the System is turned on and the source is “USB.”

• You cannot connect a computer to the USB MEMORY REC/PLAY terminal of the

System.

• Do not disconnect the USB mass storage class device when the System is turned on. It

may cause malfunction of both this System and the device.

• Noise and static electricity may stop the USB mass storage class device sound. In this

case, disconnect and connect the USB mass storage class device again after turning

off the System.

Prohibiting Disc Ejection (on the System only)

You can lock the disc tray so that no one can eject the loaded disc.

• This is possible while the System is on standby.

To cancel the prohibition, repeat the same

procedure.

Playing Repeatedly—Repeat Play

1Press repeatedly to specify the repeat mode as follows:

REP TRK: Repeats the current (or specified) track. [ ]

REP GRP: Repeats all tracks in the current group (MP3/WMA/

WAV only). [ ]

REP ALL: Repeats all tracks. [ ]

REP OFF: Normal playback

2or

Programming the Playing Order—Program Play

• Program Play functions only for discs (not for USB mass storage class device).

1Press to activate the Program Play while playback is stopped.

2Select tracks you want for Program Play.

1For MP3/WMA/WAV files only: Select a group number.

2Select a track number.

• To select a track directly, see the left column.

3Press to store the selected track.

4Repeat steps 2 3 and to program other tracks you want.

• If you try to program a 100th track, “FULL” will appear.

5The tracks are played back in the programmed order.

Operations for Program Play (while not playing)

• To check the programmed contents, press or .4 ¢

• To add tracks, repeat steps and above.2 3

• To erase the last programmed track, press CANCEL.

• To erase the entire program, press and hold CANCEL for about 2 seconds.

• To exit from Program Play, press PROGRAM.

– The stored program is kept.

Playing at Random—Random Play

• Random Play functions only for discs (not for USB mass storage class device).

1Press to activate the Random Play while playback is stopped.

2Playback starts in random order.

Random Play ends when all tracks are played back.

Operations for Random Play

• To skip a track, press .¢

• To go back to the beginning of the current track, press .4

• To exit from Random Play, press RANDOM while playback is stopped.

Thank you for purchasing a JVC product.

Front

view

Side

view

Information for Users on Disposal of Old

Equipment

[European Union only]

This symbol indicates that the product

with this symbol should not be disposed

as general household waste. If you want to

dispose of this equipment, please do not

use the ordinary dust bin! There is a separate

collection System for these products.

To Press Indication/Result

System Remote

Turn on or off

(standby) the power

The STANDBY lamp on the System turns off/on.

Select a source See “Playing Back a Disc/USB Mass Storage Class Device” on

page 4.

FM: Press to select “FM” as the source.

AM: Press to select “AM” as the source.

TUNER: Press repeatedly to select “FM” or “AM” as the source.

• See “Listening to FM and AM Broadcasts” on page 5.

See “Listening to Digital Audio Player” on page 5.

Adjust the volume Adjustable range: Level 0 (“VOL MIN”) to level 40 (“VOL MAX”).

Drop the volume in

a moment —To restore the volume, press again, or adjust the volume level.

Activate the EALA

surround mode —

The indicator lights up.

To cancel this function, press repeatedly until indicator

lights off.

Emphasize the

sound (Sound Turbo

function)

The S.TURBO indicator lights up.

To cancel this function, press again.

Reinforce the bass

sound (Active Hyper

Bass Pro function) —

The AHB PRO indicator lights up.

• When Sound Turbo function is activated (see above), this

function cannot be activated.

To cancel this function, press again when Sound Turbo

function is deactivated.

Adjust the tone

(Bass/Treble)

—

Press once for adjusting the bass level; twice for treble level,

then, press +/–.

Adjustable range: –3 to +3.

Change the display

brightness —Press when the System is turned on.

To cancel this function, press again.

Change the display

information (Clock

and Source) —

For setting the clock, see “Setting the Clock and Using Timers”

on page 7.

• When FM is selected as the source, you can check Radio Data

System information (see page 5).

Set the ECO

(ecology) Mode

Press when the System is on standby.

Setting the ECO (ecology) Mode allows you to reduce power

consumption by turning the display off while on standby.

To cancel this function, press again when the System is on

standby.

NOTE:

DO NOT turn off (standby) the System with the volume set to an extremely high level;

otherwise, the sudden blast of sound can damage your hearing, speakers and/or

headphones when you turn on the System or start playback.

To a wall outlet

Plug the AC power cord only after all connections are complete.

Rear view

Outdoor FM antenna

(not supplied)

Disconnect the supplied FM antenna, and connect to

an outdoor FM antenna using a 75 Ω wire with coaxial

type connector (IEC or DIN45325).

FM antenna (supplied)

AM loop antenna (supplied)

Turn it until the best reception

is obtained.

RESUME Play (For MP3/WMA/WAV only)

When you stop the playback, the System stores the stop point. (The RESUME

indicator lights up.)

When you start the playback again, it starts from the stored position.

To clear the stored position, press twice.7

The following operations are explained using the remote control, unless

mentioned otherwise. However, if the System has the same or similar button

names, they can also be used for the operations.

CAUTION:

Battery shall not be exposed to excessive heat such as

sunshine, fire, or the like.

NOTES:

• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas

away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.

• Make sure both the speakers are connected correctly and firmly.

• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).

• DO NOT connect more than one speaker to each terminal.

• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.

Do not connect the AC power cord until all other connections have been made.

To connect the FM antenna (supplied)

Extend it so that you can obtain the best reception.

For better FM reception

To connect the AM loop antenna (supplied) To assemble the AM loop antenna

To connect the speaker cords

Using Headphones

Be sure to turn down the volume before connecting or putting on the headphones.

• Connecting the headphones will deactivate the speakers.

• Sound adjustments also affect the sound through the headphones.

Front view

Press and hold

Insert

Release

Red

Black From left

speaker

From right

speaker

How to cancel the demonstration

Press and hold DEMO button while on standby. (Refer to the attached “Information

about the demonstration function.”)

SAFETY INSTRUCTIONS

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been designed and manufactured

to meet international safety standards but, like any

electrical equipment, care must be taken if you are to

obtain the best results and safety is to be assured.

Do read the operating instructions before you attempt to

use the equipment.

Do ensure that all electrical connections (including

the mains plug, extension leads and interconnections

between pieces of equipment) are properly made and

in accordance with the manufacturer’s instructions.

Switch off and withdraw the mains plug when making or

changing connections.

Do consult your dealer if you are ever in doubt about the

installation, operation or safety of your equipment.

Do be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in

any doubt about it working normally, or if it is damaged

in any way—switch off, withdraw the mains plug and

consult your dealer.

DON’T remove any fixed cover as this may expose

dangerous voltages.

DON’T leave equipment switched on when it is unattended

unless it is specifically stated that it is designed for

unattended operation or has a standby mode.

Switch off using the switch on the equipment and make

sure that your family know how to do this.

Special arrangements may need to be made for infirm or

handicapped people.

DON’T use equipment such as personal stereos or radios

so that you are distracted from the requirements of

traffic safety. It is illegal to watch television whilst driving.

DON’T listen to headphones at high volume as such use

can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for

example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of

the equipment.

DON’T use makeshift stands and NEVER fix legs with

wood screws—to ensure complete safety always fit the

manufacturer’s approved stand or legs with the fixings

provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain

or moisture.

ABOVE ALL

– NEVER let anyone, especially children, push anything

into holes, slots or any other opening in the case

—this could result in a fatal electrical shock.

–

NEVER guess or take chances with electrical equipment

of any kind—it is better to be safe than sorry!

USB cable (not supplied)

USB memory

(not supplied)

STANDBY lamp

Point at the remote sensor on the front panel.

(The operating range is approx. 7 m.)

Stereo mini plug cord

PHONES jack

Produkt Specifikationer

Mærke:	JVC
Kategori:	Hi-Fi system
Model:	UX-G650
Type:	Home audio micro system
Vægt:	6000 g
Produktfarve:	Sort
Udgangseffekt (RMS):	60 W
Equalizer:	Ja
Antal USB 2.0-porte:	1
Understøttede lydformater:	MP3, WAV, WMA
Dimensioner (BxDxH):	165 x 304 x 251 mm
Integreret ur:	Ja
Impedens:	6 ohm (Ω)
Understøttede radiobånd:	AM, FM
MP3-afspilning:	Ja
CD-R-afspilning:	Ja
CD-RW-afspilning:	Ja
Højttalere:	2
Signal/støjforhold:	89 dB
Optisk diskafspiller:	Ja
Afspilning af DVD-lyd:	Ja