Kenwood KAC-PS917D Manual
Læs nedenfor 📖 manual på dansk for Kenwood KAC-PS917D (2 sider) i kategorien Receiver. Denne guide var nyttig for 23 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/2
Safety precautions
WARNING
To prevent injury or fire, take the following
precautions:
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and
wiring work to professionals.
• When extending the ignition, battery, or ground wires,
make sure to use automotive-grade wires or other wires
with the range of 5 mm (AWG 10) or more to prevent
wire deterioration and damage to the wire coating.
• To prevent a short circuit, never put or leave any metallic
objects (such as coins or metal tools) inside the unit.
• If the unit starts to emit smoke or strange smells, turn
off the power immediately and consult your Kenwood
dealer.
• Do not touch the unit during use because the surface of
the unit becomes hot and may cause burns if touched.
CAUTION
To prevent damage to the machine, take the following
precautions:
• Be sure the unit is connected to a 12V DC power supply
with a negative ground connection.
• Do not open the top or bottom covers of the unit.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid places
with too much dust or the possibility of water splashing.
• When replacing a fuse, only use a new one with the
prescribed rating. Using a fuse with the wrong rating
may cause your unit to malfunction.
• To prevent a short circuit when replacing a fuse, first
disconnect the wiring harness.
NOTE
• If you experience problems during installation, consult
your Kenwood dealer.
• If the unit does not seem to be working right, consult
your Kenwood dealer.
Cleaning the unit
If the front panel gets dirty, turn off the power and wipe
the panel with a dry silicon cloth or soft cloth.
CAUTION
Do not wipe the panel with a hard cloth or a cloth
dampened by volatile solvents such as paint thinner and
alcohol. They can scratch the surface of the panel and/or
cause the indicator letters to peel off.
To prevent battery rise
When the unit is used in the ACC ON position without
turning the engine ON, it depletes the battery. Use it after
starting the engine.
Protection function
The protection function is activated in the following
situations:
This unit is equipped with a protection function for
protecting this unit and your speakers from various
accidents or problems that can occur.
When the protection function is triggered, the power
indicator goes off and the amplifier stops operating.
• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is sent to
the speaker output.
• When the internal temperature is high and unit won’t
operate.
7 Wiring
• Take the battery wire for this unit directly from the
battery. If it's connected to the vehicle’s wiring harness, it
can cause blown fuses etc.
• If a buzzing noise is heard from the speakers when the
engine is running, connect a line noise filter (optional) to
each of the battery wire.
• Do not allow the wire to directly contact the edge of the
iron plate by using Grommets.
• Connect the ground wire to a metal part of the car
chassis that acts as an electrical ground passing
electricity to the battery‘s negative terminal. Do not ·
turn the power on if the ground wire is not connected.
• Be sure to install a protective fuse in the power cord
near the battery. The protective fuse should be the same
capacity as the unit’s fuse capacity or somewhat larger.
• For the power cord and ground, use a vehicle type
(fireproof ) power wring cord. (Use a power wiring cord
with the range of 5 mm (AWG 10) or more.)
• When more than one power amplifier are going to be
used, use a power supply wiring wire and protective
fuse of greater current-handling capacity than the total
maximum current drawn by each amplifier.
7 Speaker selection
• Using speakers with smaller input ratings than the
amplifier’s output power would result in smoke
generation or equipment failure.
• Use speakers that have an impedance of 2 or greater.
When more than one set of speakers are going to
be used, calculate the combined impedance of the
speakers and then connect suitable speakers to the
amplifier.
<Example>
Combined impedance
B64-5144-00/00 (MV)© 2013 JVC KENWOOD Corporation
KAC-PS917D
CLASS D MONO POWER AMPLIFIER
INSTRUCTION MANUAL
高性能D类数字功率放大器
使用说明书
安全注意事项
警告
为了防止受伤和火灾，请遵守下列注意事项。
• 安装本产品和连接导线需要一定的技能和经验。为了保证安
全，应请专业人员完成安装和连接导线作业。
• 当延长蓄电池导线和接地导线时，请使用车辆 用导线或
5mm2（AWG 10）以上的导线，以防 止导线劣化和被覆面
的损伤。
• 为了防止短路等事故，请勿将金属物品（硬币，工具等）掉
落在装置中。
• 万一装置冒烟或有异味时，请立即关闭电源，并与建伍经销
商洽谈。
• 在使用中请尽量不要接触装置表面。因为装置在使用中表面
发热会烫伤人体。
注意
为了防止装置发生故障，请遵守下列注意事项，正确操作和
使用。
• 请以负接地线的12V直流电源向本装置供电。
• 请勿打开顶部和底部的盖子。
• 请勿将本装置安装在曝露于直射阳光，高温或高湿， 水可
能飞溅的或有灰尘的地方。
• 更换保险丝时，请更换规定容量相同的保险丝， 如使用不
同容量的保险丝，可能会造成装置的故障。
• 更换保险丝时，为了防止短路事故，请先拔下电源线束再进
行更换。
注
• 安装有困难时，请与建伍经销商洽谈。
• 如果仍不能恢复正常时，请与建伍经销商洽谈。
装置的保养
如果外表污脏时，请关闭电源，使用干燥的硅布或柔软的布
匹擦拭。
注意
请勿使用硬布或涂料稀释剂，酒精等挥发性溶剂， 以免损坏
外表面或将所附指示字符擦掉。
防止蓄电池全部放电
当本机在ACC ON位置使用而不开动发动机时，将消耗蓄电池
的电量。 请在开动了发动机之后使用。
保护功能
在以下场合中保护功能被激活
本机装有保护功能，可以保护本机以及扬声器不会受到可能
发生的各种意外事故的损害。
当保护功能被触发时，电源指示灯将熄灭，放大器也停止工
作。
• 当扬声器缆线短路时。
• 当扬声器的输出接地时。
• 当本机出现误动作，有 DC（直流） 信号传送到扬声器输出
端时。
• 内部高温不能动作时。
7 接线
• 请将本机的蓄电池连接线直接与蓄电池连接。 如果与汽车
的配线束连接，将产生烧毁保险丝等故障。
• 如果发动机运转时从扬声器中发出噪音，可以在蓄电池的每
根连线上加一个线路噪音滤波器（选购件）。
• 使用保护套，以防缆线直接接触铁板的边缘。
• 将接地线连接到车架的金属部位，车架起到车辆电气接地的
作用，将电流传递到蓄电池的负极·。 如果接地线没有连
接就不要打开电源开关。
• 应务必在蓄电池附近的电源连接线上设置保险丝。 保险丝
的规格应该与本机的保险丝容量相同或者略大。
• 对于电源连接线和接地线，请使用汽车用（防火）电源连接
线。（请使用截面积为5mm2（AWG 10）或者 以上的电源
连接线。）
• 当使用多个功率放大器时，电源导线的电流容量及保险丝的
容量要大于各个放大器的使用电流之和的最大值。
7 扬声器选择
• 使用输入额定值比放大器输出功率小的扬声器将会导致冒烟
或设备故障。
• 使用的扬声器的阻抗必须大于或等于 2 欧姆。 当使用一组
扬声器时，必须在计算扬声器的总阻抗之后，再连接合适的
扬声器。
＜例＞
综合阻抗
Troubleshooting guide
What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.
Before calling service, first check the following table for possible problems.
PROBLEM POSSIBLE CAUSE SOLUTION
No sound.
(No sound from one
side.)
(Blown fuse.)
• Input (or output) cables are disconnected.
• Protection circuit may be activated.
• Volume is too high.
• The speaker cord is shorted.
• Connect the input (or output) cables.
• Check connections by referring to
<Protection function>.
• Replace the fuse and use lower volume.
• After check the speaker cord and fixing the
cause of the short, replace the fuse.
The output level is too
small (or too large).
• The input sensitivity adjusting control is
not set to the correct position. • Adjust the control correctly referring to
<Controls>.
The sound quality is
bad.
(The sound is distorted.)
• The speakers wire are connected with
wrong / polarity.ª ·
• A speaker wire is pinched by a screw in
the car body.
• The switches may be set improperly.
• Connect them properly checking the / ª ·
of the terminals and wires well.
• Connect the speaker wire again so that it is
not pinched by anything.
• Set switches properly by referring to
<Controls>.
故障检修
有时被认为是故障的现象，其实是因微小的操作或配线失误而造成。 在要求维修之前，请参照下表稍做检查为盼。
现象 原因 排除方法
没有声音
（保险丝跳断）
· 输入（或输出）缆线未连接。
· 保护线路可能被触发。
· 音量过大。
· 扬声器电线短路。
· 连接输入（或输出）缆线。
· 参考 <保护功能> 一节，检查连接状况。
· 请更换保险丝，减小音量。
·
确认扬声器线，解除短路原因后，更换保险丝。
输出电平过低（或过高） · 输入灵敏度调节不当，没有位于妥当位置。 · 调节该控制器。请参考 <控制>。
声音质量很差
（声音失真）
· 扬声器缆线的极性 / 连接错误。ª ·
· 扬声器缆线的一根被车体螺钉压迫。
· 开关的设定可能不妥。
· 请将缆线的极性 / 连接正确。ª ·
· 重新连接缆线，使之不再受螺钉压迫。
· 请参考 <控制>，将开关正确设置。
规格
规格可能会变更，恕不另行通知。
音频部
额定输出功率 (+B = 14.4V)
(4 Ω) (20 Hz – 200 Hz, ≤ 1.0 % THD) ................. 500 W × 1
(2 Ω) (100 Hz, ≤ 1.0 % THD) ............................1000 W × 1
扬声器阻抗 .............................................4 Ω (2 Ω - 8 Ω允许)
频率响应 (+0, – 3 dB) ........................................ 20 Hz 200 Hz -
灵敏度 (RCA)......................................................... 0.2 V
- 5.0 V
信噪比 ............................................................................ 100 dB
输入阻抗 .........................................................................10 kΩ
低通滤波器过滤频率 (-24 dB/oct.) ...........50 Hz – 200 Hz (可变)
次音频过滤频率 (-24 dB/oct.) ....................20 Hz – 50 Hz (可变)
低音增强控制 (40 Hz) ....................................0 – +18 dB (可变)
共同
使用电压 ............................................... 14.4 V (允许11 - 16 V)
消耗电流 ............................................................................65 A
安装尺寸（宽×高×深）........................335 × 56 × 192 mm
重量 ................................................................................ 2.8 kg
Specifications
Specifications subject to change without notice.
Audio section
Rated power output (+B = 14.4V)
(4 ) (20 Hz – 200 Hz, ≤ 1.0 % THD) ............................. 500 W × 1
(2 ) (100 Hz, ≤ 1.0 % THD)............................................. 1000 W × 1
Speaker impedance ............................... 4 (2 to 8 allowable)
Frequency response (+0, –3 dB)............................20 Hz – 200 Hz
Input sensitivity (RCA)........................................................... 0.2 V – 5.0 V
Signal to noise ratio...........................................................................100 dB
Input impedance ...................................................................................10 k
Low pass filter frequency (-24 dB/oct.)
.....................................................................50 Hz – 200 Hz (variable)
Infrasonic Filter Frequency (-24 dB/oct.)
........................................................................20 Hz – 50 Hz (variable)
Bass Boost Control (40 Hz) ............................. 0 – +18 dB (variable)
General
Operating voltage ................................ 14.4 V (11 – 16 V allowable)
Current consumption ...........................................................................65 A
Dimensions (W × H × D) ...................................335 × 56 × 192 mm
Weight ..........................................................................................................2.8 kg
The warranty will only be honored in the country in which the unit was originally purchased.
EXPRESS WARRANTY STATEMENT FOR CAR STEREO AND
PERSONAL AUDIO COMPONENTS
JVC KENWOOD AUSTRALIA PTY. LTD. (“JVC KENWOOD”) is proud of the quality and workmanship of its audio equipment.
This unit has been properly designed, tested and inspected before it was shipped to you. If properly installed and operated in
accordance with instructions furnished, it should give optimum reliable performance.
For Australian Customers
Our goods comes with guarantees that cannot be excluded under the Australian Consumer Law. Under Australian Consumer
Law, you are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
The benefi ts of this warranty are in addition to any rights and remedies imposed by Australian State and Federal legislation
that cannot be excluded. Nothing in this warranty is to be interpreted as excluding, restricting or modifying any State or Federal
legislation applicable to the supply of goods and services which cannot be excluded, restricted or modifi ed.
For New Zealand Customers
The benefi ts of the express warranty described below are in addition to your statutory rights and remedies under the Consumer
Guarantees Act 1993 that cannot be excluded. If you are acquiring Product for the purposes of a business, to the extent
permitted by law, the Consumer Guarantees Act 1993 does not apply. Otherwise nothing in this warranty is to be interpreted as
excluding, or restricting, the Consumer Guarantees Act 1993. To the extent permitted by law, all other warranties, guarantees
or representations (whether implied by statute, common law or custom of the trade or otherwise) in respect of the Product, not
expressly included in this warranty, are excluded.
SCOPE OF EXPRESS WARRANTY
Subject to the “EXCLUSIONS”, “PROCEDURE WHEN REQUESTING SERVICE UNDER THE EXPRESS WARRANTY” and
“LIMITATIONS” below, each of the KENWOOD brand products (“Products”) is expressly warranted under normal installation
and use against defects in material and workmanship during the Warranty Period.
This warranty is not transferable to a subsequent customer if the Product is sold by the original purchaser during the Warranty Period.
During the Warranty Period, JVC KENWOOD will cause the Product or the defective part of the Product to be repaired by providing
to anyJVC KENWOOD Authorized Service Centre in Australia or New Zealand(as applicable to country of purchase) free of charge
parts necessary to correct any defect in material or workmanship. JVC KENWOOD reserves the right to replace defective parts
of the Product with parts and components of similar quality, grade and composition where an identical part or component is not
available. Products presented for repair may be replaced by refurbished products of the same type rather than being repaired.
Refurbished parts may be used to repair the goods.
WARRANTY PERIOD
The KENWOOD brand car stereo is expressly warranted for a period of from the date of the original purchase.ONE YEAR
CONDITIONS OF THE EXPRESS WARRANTY
The following are not covered by this express warranty:
1. Voltage conversions;
2. Cabinets, grilles, other exterior fi nishes, belts, tape heads, and other nondurable parts and accessories;
3. Any fault caused by faulty installation, water damage, the vehicle (including its electronically system) or connection to an incorrect
power supply;
4. Periodic check-ups which do not disclose any defects covered by this warranty;
5. Products on which the serial number has been defected, modifi ed or removed;
6. Products that have been subject to abnormal conditions, including environment, temperature, water, fi re, humidity, pressure, stress
or similar;
7. Alleged defects that are within acceptable industry variances;
8. Damage or deterioration:
a. Resulting from installation and/or removal of the product.
b. Resulting from accident, misuse, abuse, neglect, unauthorized product modifi cation or failure to follow instructions contained
in the Owner’s Manual.
c. Resulting from installation of parts or accessories that do not conform to the quality or specifi cations of the original parts or
accessories.
d. Occurring during shipment (claims must be present to shipper); and
9. Damaged magnetic tapes.
The warranty does not extend to:
1. Installation and removal charges; or
2. Shipping charges to or from an authorised JVC KENWOOD Service Centre.
PROCEDURE WHEN REQUESTING SERVICE UNDER THE WARRANTY
1. When requesting service under JVC KENWOOD warranty, preferably make your Product available for inspection and testing to the
dealer from whom you made the purchase, or to the nearest Authorised JVC KENWOOD Service Centre for KENWOOD products,
or ship your Product in its original packaging, or equivalent, with shipping charges and insurance prepaid, to the Authorised JVC
KENWOOD Service Centre for KENWOOD products. Otherwise, contact JVC KENWOOD at the contact address listed below.
. Attach the following to the Product:
. the warranty record in the back of this page together;
. a valid purchase docket attached; and
. detailed description of the problem encountered, including details of any problems which relate to associated equipment.
2.
If such inspection and testing fi nd no defect in the Product, the purchaser, at JVC KENWOOD’s discretion must pay JVC KENWOOD’s cost
of service work, evaluation and testing.
3. Make sure you recover this card, your purchase docket and repair docket when accepting the equipment back after repair or after
your claim is rejected.
IMPORTANT NOTICE
1. Proper maintenance and use are important to the performance level of all KENWOOD brand products. Therefore, you should read
your instruction manual.
2. Retain your purchase docket together with this warranty record in a safe place, and present them both to prove your eligibility for
warranty service.
3. We recommend that you keep all the original packaging as it provide the best protection you can have for transportation of your
equipment in the future.
4. Location of nearest JVC KENWOOD Service Centre can be obtained from the dealer.
LIMITATIONS
To the extent permitted by law, JVC KENWOOD makes no express warranties or representations other than set out in this warranty.
The repair or replacement of the unit or part of the unit is the absolute limits of JVC KENWOOD’s liability under this express warranty.
JVC KENWOOD AUSTRALIA PTY. LTD.
4 TALAVERA ROAD, NORTH RYDE
N.S.W. 2113, AUSTRALIA
TEL. (02) 8879-2211
FAX. (02) 8879-2255
svcdept@kenwood.com.au
AUSTRALIA/NEW ZEALAND JVC KENWOOD AUSTRALIA PTY. LTD.
Warranty Card
Model number & serial number
Dealer & stamp
Purchase date
Name & address of customer
Attention:
This card and receipt (or invoice) are necessary to purchase a new panel in case of
theft or damage.
Dear Customer,
Thank you for purchasing this kenwood product. As mentioned in the pages of this booklet,
our warranty is only valid in the countries listed. If your country is not listed please contact
your retailer for information on warranty procedure, or write to:
JVC KENWOOD Customer Information Center
3-12, Moriyacho, Kanagawa-ku, Yokohama-shi, Kanagawa 221-0022, Japan
Produkt Specifikationer
| Mærke: | Kenwood |
| Kategori: | Receiver |
| Model: | KAC-PS917D |
Har du brug for hjælp?
Hvis du har brug for hjælp til Kenwood KAC-PS917D stil et spørgsmål nedenfor, og andre brugere vil svare dig
Receiver Kenwood Manualer
28 Juni 2024
28 Juni 2024
20 Maj 2024
11 April 2024
6 April 2024
21 Marts 2024
20 Marts 2024
23 Februar 2024
19 Februar 2024
19 Februar 2024
Receiver Manualer
- Receiver SilverCrest
- Receiver Denver
- Receiver Sencor
- Receiver Sony
- Receiver Fenton
- Receiver Panasonic
- Receiver VOX
- Receiver Pro-Ject
- Receiver Anthem
- Receiver IFM
- Receiver Musway
- Receiver Audio-Technica
- Receiver Peavey
- Receiver Pioneer
- Receiver TOA
- Receiver Hifonics
- Receiver Sharp
- Receiver Qtx
- Receiver Dynacord
- Receiver Logitech
- Receiver Behringer
- Receiver Emos
- Receiver MB Quart
- Receiver Smart
- Receiver Sennheiser
- Receiver Harman Kardon
- Receiver Garmin
- Receiver Grundig
- Receiver Roland
- Receiver Asus
- Receiver Golden Age Project
- Receiver Pyle
- Receiver Argon
- Receiver Roksan
- Receiver Denon
- Receiver Yamaha
- Receiver Matsui
- Receiver Nedis
- Receiver Kicker
- Receiver Optoma
- Receiver Renegade
- Receiver LD Systems
- Receiver Hama
- Receiver Auna
- Receiver Thomson
- Receiver Aiwa
- Receiver Rega
- Receiver Yorkville
- Receiver Pyle Pro
- Receiver JBL
- Receiver AKAI
- Receiver Teufel
- Receiver DataVideo
- Receiver Strong
- Receiver RCF
- Receiver Optex
- Receiver Smartwares
- Receiver Chandler
- Receiver Trust
- Receiver Blaupunkt
- Receiver JVC
- Receiver Hilti
- Receiver Crunch
- Receiver Medion
- Receiver Megasat
- Receiver Cambridge
- Receiver Tangent
- Receiver Cisco
- Receiver König
- Receiver TechniSat
- Receiver Bose
- Receiver Jabra
- Receiver Alpine
- Receiver Salus
- Receiver Triax
- Receiver Tripp Lite
- Receiver Mercury
- Receiver Genie
- Receiver KEF
- Receiver Technics
- Receiver Summit Audio
- Receiver Jensen
- Receiver Alecto
- Receiver Icom
- Receiver Astro
- Receiver Plantronics
- Receiver Krüger&Matz
- Receiver Canal Digital
- Receiver Marmitek
- Receiver PreSonus
- Receiver Kopul
- Receiver Kathrein
- Receiver Sonos
- Receiver NAD
- Receiver Tascam
- Receiver Bogen
- Receiver Omnitronic
- Receiver Velleman
- Receiver Marshall
- Receiver Sonance
- Receiver Vivotek
- Receiver Bush
- Receiver JUNG
- Receiver Fostex
- Receiver MIPRO
- Receiver Dual
- Receiver Electro-Voice
- Receiver HQ Power
- Receiver Fredenstein
- Receiver RME
- Receiver Sagem
- Receiver Onkyo
- Receiver Focal
- Receiver Line 6
- Receiver HK Audio
- Receiver Teac
- Receiver GlobalSat
- Receiver Imperial
- Receiver Autotek
- Receiver Magnat
- Receiver Saramonic
- Receiver Thorens
- Receiver Marantz
- Receiver ELAC
- Receiver Hartke
- Receiver McIntosh
- Receiver Hertz
- Receiver American Audio
- Receiver ART
- Receiver Monacor
- Receiver Samson
- Receiver Audizio
- Receiver JL Audio
- Receiver Raymarine
- Receiver Rupert Neve Designs
- Receiver Chamberlain
- Receiver FiiO
- Receiver DBX
- Receiver Warm Audio
- Receiver Devolo
- Receiver Simrad
- Receiver Galaxy Audio
- Receiver Renkforce
- Receiver Marshall Electronics
- Receiver Chord
- Receiver Alto
- Receiver Audiolab
- Receiver Music Hall
- Receiver APart
- Receiver LogiLink
- Receiver Brondi
- Receiver Kramer
- Receiver Rotel
- Receiver Black Lion Audio
- Receiver Naim
- Receiver Solid State Logic
- Receiver Citronic
- Receiver RDL
- Receiver NAV-TV
- Receiver TV Star
- Receiver Edision
- Receiver Sound Devices
- Receiver Morel
- Receiver Avalon
- Receiver Xantech
- Receiver Crest Audio
- Receiver Oculus VR
- Receiver Lindell Audio
- Receiver Audio Limited
- Receiver Rockford Fosgate
- Receiver Fosi Audio
- Receiver Vivolink
- Receiver Memphis Audio
- Receiver Crestron
- Receiver DAP-Audio
- Receiver Vincent
- Receiver Adastra
- Receiver Lectrosonics
- Receiver AudioControl
- Receiver Steren
- Receiver Ocean Matrix
- Receiver Orava
- Receiver HiFi ROSE
- Receiver Classé
- Receiver Musical Fidelity
- Receiver NuPrime
- Receiver Artsound
- Receiver Ram Audio
- Receiver Apantac
- Receiver Ferguson
- Receiver SRS
- Receiver Cabasse
- Receiver DLS
Nyeste Receiver Manualer
30 Juni 2024
30 Juni 2024
30 Juni 2024
29 Juni 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024
28 Juni 2024