Kern FL 5 Manual

Kern Måling FL 5

Læs nedenfor 📖 manual på dansk for Kern FL 5 (21 sider) i kategorien Måling. Denne guide var nyttig for 46 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/21
FL- -e-2020.docx BA
Sauter GmbH
Ziegelei 1
D-72336 Balingen
e-mail: info@kern-sohn.com
Phone : +49- [0]7433- -0 9933
Fax: +49- [0]7433-9933- 149
Internet: www.sauter.eu
Instruction manual digital force
gauge
SAUTER FL
Version 2.0
01/2020
GB
PROFESSIONAL MEASURING
2 - -e-2020.docx FL BA
GB
Congratulations on purchasing a digital force measuring device with internal or external
measuring cell from SAUTER. We hope you will enjoy your quality measuring device
with a wide range of functions. Please do not hesitate to contact us if you have any
questions, requests or suggestions.
Table of contents:
1 Introduction .....................................................................................................3
2 Scope of delivery ........................................................................................... 3
3 Additional information when using the AFH software ................................ 3
4 Technical data ................................................................................................ 4
4.1 Technical data FL with internal loadcell up to 1 kN............................................................... 4
4.2 Technical data FL with external loadcell from 2kN ............................................................... 5
4.3 Technical data external load cell (from 2kN) ......................................................................... 6
4.4 Technical Data FL TM 7...............................................................................................................
5 Battery indicator / power supply .................................................................. 8
6 Display indication .......................................................................................... 8
7 Control buttons .............................................................................................. 9
8 Functions ...................................................................................................... 10
8.1 Limit value display Good / Bad ............................................................................................. 10
8.2 Invert display .......................................................................................................................... 10
8.3 Store measured value in memory ......................................................................................... 10
8.4 Memory / Storage ................................................................................................................... 11
8.5 Diagnostics ............................................................................................................................. 12
8.6 Select Output .......................................................................................................................... 12
9 Computer control of the force gauge ......................................................... 13
10 RS232 output signal .................................................................................... 13
10.1 Interface protocol ................................................................................................................... 14
10.2 Assignment of the RS232 data interface .............................................................................. 14
11 Warnings ...................................................................................................... 15
12 Adjustment instruction FL .......................................................................... 17
13 Technical drawings ...................................................................................... 21
FL- -e-2020.docx 3 BA
1 Introduction
Please read these operating instructions carefully before commissioning, even if you
already have experience with SAUTER measuring instruments.
After receipt of the force gauge, it should be checked in advance that no transport
damage has occurred, that the outer packaging, the plastic housing, other parts or
even the gauge itself have not been damaged. If any damage is evident, please
notify SAUTER GmbH immediately.
The FL can measure tensile and compressive forces very accurately and it is easy to
operate. It can be held in the hand for measurements or mounted on top of a suitable
test stand.
SAUTER oers optional software and accessories to make the measuring instrument
more versatile in use. Please ask SAUTER or the SAUTER supplier or visit our
website
www.sauter.eu.
2 Scope of delivery
• SAUTER , incl. internal battery FL
• Transport case
• Battery charger
• 5 pieces M3 x 8 screws for mounting on SAUTER test benches
3 Additional information when using the AFH software
If you want to connect an FL with the combination test bench and software (AFH-LD
or AFH-FD) to a , you must connect the FL to the equipment port of the test bench PC
via the FL-A04 cable (Sub-D 9-pin to PS2) and connect the test bench to the PC via
the computer port.
4 - -e-2020.docx FL BA
4 Technical data
4.1 Technical data with internal loadcell up to 1kN FL
Measuring
device
FL 5
FL 10
FL 20
FL 50
FL 100
FL 200
FL 500
FL 1K
Capacity
5N
10N
20N
50N
100N
200N
500N
1000N
Measurement
uncertainty
±0.2% of Max (measuring range)
Work
temperature
15°C 35°C to
Relative air
humidity
15% to 80% Humidity
Weight
(without
accessories)
Approx. 500g
Dimensions
Display unit
(LxWxH)
160x75x30mm
Thread
M6
FL- -e-2020.docx 5 BA
4.2 Technical data FL with external loadcell from 2kN
Measuring
device
FL 2k
FL 5k
FL 10k
FL 20k
Capacity
2000N
5000N
10000N
20000N
Measurement
uncertainty
±0.2% of Max (measuring range)
Working
temperature
15°C 35°C to
Relative air
humidity
15% to 80% Humidity
Weight display
unit
Approx. 500g
Dimensions
display unit
(LxWxH)
160x75x30mm
6 - -e-2020.docx FL BA
4.3 Technical data external load cell (from 2kN)
Maximum
load
LxWxH
Thread type
Cable
length
2 kN
76x51x19mm
M12x1.75
Approx.
2,5m
5 kN
76x51x28mm
M12x1.75
10 kN
76x51x28mm
M12x1.75
20 kN
76x51x28mm
M12x1.75
FL- -e-2020.docx 7 BA
4.4 Technical Data FL TM
4.4.1 Sensors
Sensor must be ordered separately. Service FL-C01 necessary.
4.4.2 Load cell connection
Solder the cable from the measuring cell to the supplied connector. The pin
assignment at the connector is as follows:
Pin 1: Supply ( - )
Pin 2: Signal ( + )
Pin 3: Signal ( - )
Pin 4: Supply ( + )
Pin 1: EXC ( - )
Pin 2: Signal ( + )
Pin 3: Signal ( - )
Pin 4: EXC ( + )
Adjustable
measuring
ranges
5N; 10N; 25N;
50N; 100N;
250N; 500N
1kN; 2,5kN; 5kN;
10kN; 20kN;
50kN
Characteristic
value max.
1mV/V
2mV/V
Measurement
uncertainty
±0,2% bis 1% von Max
(Messbereich), abhängig von
verwendetem Sensor
Working
temperature
15°C bis 35°C
Weight display
unit
Ca. 500g
Dimensions
display unit
(LxWxH)
160x75x30mm
8 - -e-2020.docx FL BA
6
7
4
2
3
5
8
1
5 Battery indicator / power supply
Battery level > 4.8 V
4.8 V > Battery level > 4.7 V
4.7 V > Battery level > 4.4 V
4.4 V > Battery level > 4.0 V
Battery level < 4.0 V
• If the battery voltage is less than 3.9V, a message appears that the battery
is exhausted and the device switches o automatically
The FL is equipped with four Nickel Metal Hybrid (NiMH) batteries type AAA. For
safety reasons during transport, the batteries are supplied uncharged. For maximum
battery life, we recommend that you charge the batteries only with the original
charger (supplied) for a period of 14-16 hours before using the meter for the first
time.
6 Display indication
Position
Description
1
Measurement result
2
Display mode (track, peak (pull), peak (push)
3
Display of the direction of force
4
battery charge indicator
5
Number of occupied memory locations
6
Activated pass-fail criterion
7
Display unit of the measurement result
8
Force diagram
FL- -e-2020.docx 9 BA
7 Control buttons
MENU/ESC:
• Opens the menu window with the individual submenus
• By pressing the MENU/ESC button in the menu, you can return to the previous
page
ZERO (zeroing):
• Zeroing the display in track mode (tare function)
ENTER:
• Conrm the selection in the menu
• Saving a measured value in PEAK mode
PRINT (print function):
• Output of the memory contents to PC or printer
RESET (delete function):
• Delete the current PEAK value
UNIT (units of measurement):
• Press the key briey: Switch between N, gf, kgf, ozf, lbf, mN
Mode (mode change):
Assignment with three functions:
• Track mode (continuous measurement)
• Peak Mode Train
• Peak Mode Print
ON / OFF:
• On / O button (press button for approx. 1 s)
FL- -e-2020.docx BA 11
8.4 Memory / Storage
The memory is used to view the stored data. It can store 500 readings. Currently,
individual entries or all entries can be deleted, or the measurement data of the
memory can be printed out.
To enter the MEMORY menu, the MENU/ESC button must be pressed. Use the UP
or DOWN button to move the cursor to MEMORY. Then conrm with the ENTER
button and you are on the memory page. Press the ESC button to return to the main
menu page.
With the arrow keys UP and DOWN the page can be changed within the memory and
by pressing and holding one of these two keys it is possible to scroll up or down.
By pressing the PRINT key, the memory contents can be printed out via the serial
port.
By pressing the ZERO button, the DELETE menu is accessed
Use the UP and DOWN arrow keys to select the desired delete option. If is NO
selected here and conrmed with the ENTER key, the meter returns to the memory
page.
When DELETE is selected and the ENTER button is pressed to conrm, the currently
stored measurement is deleted and the instrument returns to the memory page.
When DELETE ALL is selected and the ENTER button is pressed to conrm, all
stored measurements are deleted and the instrument returns to the memory page.

Produkt Specifikationer

Mærke: Kern
Kategori: Måling
Model: FL 5

Har du brug for hjælp?

Hvis du har brug for hjælp til Kern FL 5 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Måling Kern Manualer

Kern

Kern ORA 1WB Manual

19 November 2024
Kern

Kern HMM-NP Manual

17 September 2024
Kern

Kern HDD 100-1 Manual

17 September 2024
Kern

Kern HBD 100-0 Manual

17 September 2024
Kern

Kern HBA 100-0 Manual

17 September 2024
Kern

Kern HO 5K Manual

11 September 2024
Kern

Kern FS 4-500 Manual

11 September 2024
Kern

Kern FH 100KUK Manual

11 September 2024
Kern

Kern HK-DB Manual

11 September 2024
Kern

Kern HN-D Manual

11 September 2024

Måling Manualer

Nyeste Måling Manualer

Uni-T

Uni-T LM320F Manual

5 April 2025
Parkside

Parkside PWBKA 4 A1 Manual

30 Marts 2025
General

General MMD4E Manual

26 Marts 2025
PCE Instruments

PCE Instruments PCE-HT 110 Manual

26 Marts 2025
Uni-T

Uni-T UT202+ Manual

18 Marts 2025
Extech

Extech 44550 Manual

17 Marts 2025
PCE Instruments

PCE Instruments PCE-RDM 5 Manual

14 Marts 2025
Panasonic

Panasonic BE-A401P Manual

9 Marts 2025
Phoenix Contact

Phoenix Contact MM-EE-EEM-EM377 Manual

5 Marts 2025
TFA

TFA STYLE 30.5021 Manual

4 Marts 2025