Lastolite Cubelite LiteTable Manual

Lastolite Andet kameratilbehør Cubelite LiteTable

Læs gratis den danske manual til Lastolite Cubelite LiteTable (3 sider) i kategorien Andet kameratilbehør. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Lastolite Cubelite LiteTable, eller vil du spørge andre brugere om produktet?

Side 1/3
1. Remove items from the box. You should have:
- Bag containing the LiteTable (flat)
- 4 x Black support rods
- 4 x joining clips for the rods
- Back frame rod assembly
- Circular acrylic sheet
- Roll of translucent film
- Fabric back drop
Remove the LiteTable from the protective bag.
2. Lay the LiteTable on the floor and position the end of
one of the rods on the corner of the lower steel rim.
Ensure the steel rim locates into the jaws of the tip at
the end of the rod.
3. Pull the two steel rims away from each other and locate
the jaws of the tip at the other end of the rod into the
upper rim.
4. Repeat steps 2&3 for the remaining three corners.
When all four rods are in place, check they are all in a
vertical position.
5. Place the circular acrylic sheet on the top of the
LiteTable (Take care not to drop this as it will break).
6. The base unit is now complete.
7. Take hold of the back frame rod assembly and allow
the rods to ‘snap’ into position. This will form one
complete ‘U’ shaped structure.
8. Ensure that all the Silver’ joints are fully inserted into
the hollow black support rods.
9. Position the LiteTable so that the rear opening is in
front of you. Line the back frame assembly up with the
two rear support rods on the LiteTable base unit.
10. Use the four joining clips to attach the rods together.
Place one two inches from the bottom and one two
inches from the top of each of the rear support rods
on the LiteTable base unit. The clips simply snap shut
around the rod. Then attach the back frame assembly
in the same way.
11. The back frame assembly is now in place
12. Take the fabric back drop and with the smooth side
facing the front, wrap the top edge over the the
crossbar on the back frame structure and attach to the
velcro. This should leave a velcro strip facing forward
across the top of the back frame.
13. Unroll the translucent film. Then attach the velcro strip
at one end of the film to the velcro strip at the top of
the back frame. Allow the film to drop onto the top of
the base unit creating an infinity curve.
14. Take the bottom of the fabric back drop and ensure it
lays over the top of the black rim on the edge of the
LiteTable base unit (do not let it hang down the back of
the base unit). This ensures the black edge cannot be
seen through the translucent film.
15. Add your chosen lighting system. Refer to the label
near the rear opening of the LiteTable for advice on
how to position the light source inside.
Breaking Down your LiteTable kit.
16. Remove the translucent film, roll up and return to tube.
17. Remove and roll up the fabric back drop. This can also
go in the tube with the film for protection.
18. Disconnect the back frame assembly from the support
rods. To dismantle the frame pull the rods apart and
fold them so they cannot snap’ back into position.
19. Remove the circular acrylic sheet from the top of the
base unit and return it to the protective bag.
20. Remove the supporting rods from the base unit and
allow the two steel rims of the LiteTable to lie on top
of each other. Return them to the protective bag.
21. Return all the items to the storage box.
Setting up your LiteTable
1 2 3
4 5 6
7 8 9
10 1211
13 14 15
A
02.07
Setting up your LiteTable
Montaje de Lite Table
1. Retirar los componentes de la caja. En el volumen suministrado deben
estar in-cluidos los siguientes componentes:
- Bolsa con Lite Table (plana)
- 4 barras de soporte negras
- 4 pinzas para las barras
- Grupo de barras del marco trasero
- Pantalla de acrílico redonda
- Rollo con film transparente
- Fondo de tela
Retirar el módulo Lite Table de la bolsa de protección.
2. Colocar el módulo Lite Table en el suelo y pasar el extremo de una de
las barras por la esquina del aro de acero inferior. Asegurarse que el aro
de acero encaje en los ganchos de la punta en el extremo de la barra.
3. Estirar ambos aros de acero en la dirección contraria y llevar los
ganchos de la punta en el otro extremo de la barra hasta el aro superior.
4. Repetir los pasos 2 & 3 para las otras tres esquinas. Una vez montadas
las cuatro barras, controlar si se encuentran en posición vertical.
5. Colocar la pantalla de acrílico redonda sobre el módulo Lite Table. (No
dejar caer esta pantalla, de lo contrario se romperá.)
6. Ahora el módulo de base está completo.
7. Sujetar el grupo de barras del marco trasero y dejar abrir las barras. Las
mismas crearán una forma cerrada en U.
8. Asegurarse que todas las uniones plateadas estén insertadas
completamente en las barras de soporte negras huecas.
9. Colocar la Lite Table de tal forma que la abertura trasera quede para
delante. Posicionar el grupo del marco trasero con ambas barras de
soporte traseras sobre el módulo de base Lite Table.
10. Unir las barras con las cuatro pinzas. Instalar una pinza a dos pulgadas
del fondo de la barra trasera respectiva y la otra a dos pulgadas de la
punta de la barra en el módulo de base Lite Table. Las pinzas se cierran
automáticamente alrededor de la barra. Después montar el grupo del
marco trasero de la misma forma.
11. Ahora el grupo del marco trasero está montado.
12. Sostener el fondo de tela con la parte lisa hacia delante, enrollar la
esquina supe-rior por la barra transversal en el marco trasero y fijarlo
con el cierre de velcro. La cinta de velcro debe quedar en la frente sobre
la parte superior del marco trasero.
13. Desenrollar el film transparente. Unir la cinta de velcro en un extremo del
film con la cinta de velcro arriba del marco trasero. Dejar caer el film por
encima del módulo de base de forma que resulte una curva infinita.
14. Tomar el borde inferior del fondo de tela y colocarlo sobre la parte
superior del aro negro en el borde del módulo de base Lite Table (no
dejar colgar por la parte trasera del módulo de base). De esa forma se
garantiza que el borde negro no se vea a través del film transparente.
15. Conectar el sistema luminoso adecuado. En la etiqueta en la abertura
trasera del módulo Lite Table encontrará indicaciones sobre el
posicionamiento interno de la fuente luminosa.
Desmontaje de Lite Table
16. Retirar el film transparente, enrollarlo y colocarlo nuevamente en el rollo
de protección.
17. Retirar el fondo de tela y enrollarlo. El fondo igualmente se puede
guardar en el rollo de protección.
18. Soltar el grupo de marco trasero de las barras de soporte. Para
desmontar el mar-co separar las barras y después plegarlas para que no
se puedan volver a desple-gar.
19. Retirar la pantalla de acrílico redonda del módulo de base y colocarla
nuevamen-te en la bolsa de protección.
20. Retirar las barras de soporte del módulo de base. Colocar ambos aros
de acero uno encima de otro y después ponerlos en la bolsa de
protección.
21. Colocar todos los componentes en la caja para guardarlos.
Montieren des Lite Table
1. Die Komponenten aus dem Kasten nehmen. Folgende Komponenten
müssen im Lieferumfang enthalten sein:
- Tasche mit dem Lite Table (flach)
- 4 x schwarze Trägerstangen
- 4 x Verbindungsklammern für die Stangen
- Rückseitige Rahmenstangengruppe
- Runder Acrylschirm
- Rolle mit Transparentfolie
- Textilhintergrund
Den Lite Table aus der Schutztasche nehmen.
2. Den Lite Table auf den Boden legen und das Ende einer der Stangen in
die Ecke der unteren Stahleinfassung führen. Sicherstellen, dass die
Stahleinfassung in die Klauen der Spitze am Ende der Stange greift.
3. Die beiden Stahleinfassungen in entgegengesetzte Richtung ziehen
und die Klauen der Spitze am anderen Ende der Stange in die obere
Einfassung führen.
4. Die Schritte 2 & 3 für die anderen drei Ecken wiederholen. Wenn alle
vier Stangen montiert wurden, kontrollieren, ob sie in ihrer Position
vertikal ausgerichtet sind.
5. Den runden Acrylschirm auf dem Lite Table aufstellen. (Diesen Schirm
nicht fallenlassen, da er andernfalls zerbricht.)
6. Das Basismodul ist jetzt vollständig.
7. Die rückseitige Rahmenstangengruppe festhalten und die Stangen
ausklappen lassen. Sie bilden eine geschlossene U-Form.
8. Sicherstellen, dass alle silberfarbenen Verbindungen vollständig in die
hohlen schwarzen Trägerstangen eingeführt werden.
9. Den Lite Table so aufstellen, dass die rückseitige Öffnung nach vorn
weist. Die rückseitige Rahmengruppe mit den beiden rückseitigen
Trägerstangen auf dem Lite Table Basismodul ausrichten.
10. Die Stangen mit den vier Verbindungsklammern zusammenfügen. Eine
Klammer zwei Zoll vom Boden der jeweiligen rückseitigen
Trägerstange, die andere zwei Zoll von der Spitze der Stange am Lite
Table Basismodul anbringen. Die Klammern schließen sich automatisch
um die Stange. Dann die rückseitige Rahmengruppe auf dieselbe
Weise montieren.
11. Die rückseitige Rahmengruppe ist jetzt montiert.
12. Den Textilhintergrund mit der glatten Seite nach vorn halten, die obere
Kante über die Querstange am rückseitigen Rahmen wickeln und mit
dem Klettverschluss fixieren. Das Klettband muss nach vorn über den
oberen Teil des rückseitigen Rahmens weisen.
13. Die Transparentfolie abwickeln. Das Klettband an einem Ende der Folie
mit dem Klettband oben am rückseitigen Rahmen verbinden. Die Folie
auf das Basismodul fallen lassen, so dass eine Endloskurve entsteht.
14. Den unteren Rand des Textilhintergrunds fassen und über den oberen
Teil der schwarzen Einfassung am Rand des Lite Table Basismoduls
legen (nicht an der Rückseite des Basismoduls herunterhängen
lassen). Damit wird gewährleistet, dass der schwarze Rand durch die
Transparentfolie nicht zu sehen ist.
15. Das geeignete Beleuchtungssystem anschließen. Auf dem Etikett
neben der rückseitigen Öffnung des Lite Table finden sich Hinweise zur
internen Positionierung der Lichtquelle.
Zerlegen des Lite Table
16. Die Transparentfolie entfernen, aufrollen und wieder in die Schutzrolle
führen.
17. Den Textilhintergrund entfernen und aufrollen. Der Hintergrund lässt
sich ebenfalls in der Schutzrolle unterbringen.
18. Die rückseitige Rahmengruppe von den Trägerstangen lösen. Um den
Rahmen zu zerlegen, die Stangen auseinander ziehen und dann
zusammenlegen, damit sie sich nicht wieder ausklappen können.
19. Den runden Acrylschirm vom Basismodul entfernen und wieder in die
Schutztasche legen.
20. Die Trägerstangen vom Basismodul entfernen. Die beiden
Stahleinfassungen des Lite Table aufeinander und dann in die
Schutztasche legen.
21. Alle Komponenten in den Aufbewahrungskasten geben.


Produkt Specifikationer

Mærke: Lastolite
Kategori: Andet kameratilbehør
Model: Cubelite LiteTable

Har du brug for hjælp?

Hvis du har brug for hjælp til Lastolite Cubelite LiteTable stil et spørgsmål nedenfor, og andre brugere vil svare dig




Andet kameratilbehør Lastolite Manualer

Andet kameratilbehør Manualer

Nyeste Andet kameratilbehør Manualer