Leisure BSS1 Manual

Leisure Køkkenvask BSS1

Læs gratis den danske manual til Leisure BSS1 (2 sider) i kategorien Køkkenvask. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Leisure BSS1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

05/04 1824

1. With soft sharp pencil, mark ﬁ nal position of sink top,

by measurement, on the work top allowing for clear-

ance of cabinet frame work.

2. Place sink-top in correct position on worktop then

reverse front to rear, not end for end.

With sharp soft pencil

draw round sink as

accurately as possible

making sure that this

outline coincides with

ﬁ nal position marked

previously.

3. Remove sink top and mark another line 20mm inside

the sink top outline, following the corner radii with

care.

This is the cutting line for the aperture.

4. Drill as large a hole as possible inside the cutting

line. Using a pad saw, jig saw or similar, cut out the

aperture to the cutting line.

5. The sink should then be placed in the aperture

where it will rest on the T-Nuts. The T-Nuts should

be marked round carefully with a pencil making sure

that the sink is parallel to the worktop edge.

6. The sink is then removed and a 8mm hole is drilled

on the centre of each T-Nut position, countersunk

on the underside of the worktop and counterbored

from the top with a 10mm diameter drill 13mm deep

to accept the T-Nut.

Stainless Steel Inset Sinks with T-nut Fixing

7. The sinktop should then be placed in position to check

for ﬁ nal ﬁ tting.

8. Turn the sink upside down and ﬁ ll the outer pe-

rimeter with a suitable sealing compound, (Bostik

Glazing Compound, Prestik Sealing Compound and

Arborseal have been found suitable). The sealing

compound should be sufﬁ cient to ﬁ ll the rim but any

excess should be pressed down with a warm knife so

that it is evenly spread around the sink perimeter.

9. Now ﬁ t the sink to the worktop, ﬁ rmly in position and

press down evenly if possible using heavyweights

around the perimeter. Enter the screws and screw

gently home. The weights will cause the sealing

compound to settle to the proﬁ le of the sink perim-

eter, and the screws will need to be tightened slowly

and gently or distortion of the sink perimeter will

result from too great a local pressure. After one hour

remove the weights and dress off any surplus com-

pound from around the sink ﬂ ange, with a wooden or

plastic spatula, taking care not to damage the plastic

laminate.

10. After twenty-four hours, check the tightness of the

T-Nuts but do not over-tighten. If the ﬁ xing screw bot-

toms because of over length, remove and hacksaw

12mm from end of thread, and reﬁ t.

Recommended tightening sequence for sink

ﬁ xing clips

05/04 1824

After Care Stainless Sinks

Day to Day Care

Routine cleaning of your stainless steel sink is

easy if the following simple procedure is followed

After use wipe the bowl and drainer with a soft

damp soapy cloth, rinse with clean water. In hard-

water areas, an application of Jif will avoid any

build-up of dull ﬁ lm of waterborne deposits.

Although stainless steel is an extremely durable

material and will withstand a great deal of hard

use, it can be scratched by hard or sharp objects.

If the surfaces are to be kept in a blemish free

condition reasonable care should be taken when

handling such items.

Discolouration and Heavy Staining

Staining of stainless steel in most cases is due

to something being deposited on the steel rather

than an attack on the material itself. The most

common cause of staining is the build up of a thin

ﬁ lm of water borne deposits on the sink surface,

often ﬁ rst seen as a rainbow effect. The build up of

such a ﬁ lm can be avoided by drying the surface

of the sink after use as described above. How-

ever, should such a ﬁ lm appear, it can be readily

removed with a soft damp cloth and Jif. To remove

the ﬁ lm, apply the Jif neat and rub vigorously with

a damp cloth along the length of the sink surface.

After cleaning rinse thoroughly with clean water

and dry. Wire wool products and ferrous water

supply pipes can leave minute ferrous particles

adhered to the sink surface. Since stainless steel

under normal conditions does not rust, these par-

ticles can cause the appearance of small brown

rust stains. These stains can be removed using

the procedure described above.

CAUTION :

Certain household products contain substances

which will attack the stainless steel surface, they

are :

1. Bleaches :

Most common domestic bleaches contain Chlorine

in the form of a hypochlorite. Chlorine attacks the

microscopic Chromium Oxide ﬁ lm on the surface

and can cause pitting of the surface. Bleaches

should always be used in the prescribed strength

speciﬁ ed by the manufacturers. Undiluted bleach-

es can cause pitting and staining of the surface

and should be immediately rinsed off with plenty

of clean water. All cleaning agents containing

hypochlorites are unsuitable for use with stainless

steel and, even highly diluted, can cause pit-

ting under certain conditions. For this reason it is

strongly recommended that the sink is not used for

soaking clothes or cleaning clothes in hypochlorite

solutions for long periods.

2. Silver Dip Cleaners :

These are particularly harmful since they contain

strong acids which can cause discolouration and

pitting. The ﬁ rst sign of this is an iridescent rain-

bow stain which turns an etched dull grey colour.

Should any Silver Dip Cleaner come into contact

with the surface of the sink it should be immedi-

ately rinsed off with plenty of clean water.

3. Corrosive Foodstuffs :

Fruit juices, damp salt, vinegar, readymade mus-

tards, pickle and mayonnaise can cause pitting

and corrosion if left in contact with the stainless

steel surface for long periods.

4. Acids :

Sulphuric, Hydrochloric and other strong acids will

cause pitting corrosion, as will photographic devel-

oping liquids. All should be immediately washed

off with plenty of clean water if contact occurs.

Cleaning :

Always use a soft cloth. The use of coarse grit

scouring powders or soap ﬁ lled wire wool cleaning

pads is not recommended, since both will mark the

surface of the sink. Wire wool pads can leave tiny

fragments of wire embedded in the surface and

these can rust and leave small brown rust stains.

Vigorous rubbing with a soft cloth, JIF, neat deter-

gent, cleaning cream or liquid will remove these

stains. Always remove wet cleaning aids (cloths,

containers, etc.) from the sink surface after use in

order to avoid the formation of water marks and

rust stains.

Produkt Specifikationer

Mærke:	Leisure
Kategori:	Køkkenvask
Model:	BSS1
Bredde:	508 mm
Dybde:	419 mm
Produktfarve:	Rustfrit stål
Første skål, dybde:	195 mm
Første skål, dimensioner (BxL):	470 x 380 mm
Antal vaskeskåle:	1 skåle
Vask, type:	Top-monteret vask
Vask form:	Rektangulær
Vask materiale:	Rustfrit stål
Facon på første vask:	Rektangulær
Vandhane, hul:	Ja
Vandhane inkluderet:	Ingen