LiftMaster 78LM Manual


Læs nedenfor 📖 manual på dansk for LiftMaster 78LM (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 17 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
MODELS 78LM AND 78LMC
MULTI-FUNCTION DOOR CONTROL
OWNERS INSTRUCTIONS
To prevent possible SERIOUS INJURY or DEATH from electrocution:
Be sure power is NOT connected BEFORE installing door control.
Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
Install door control within sight of garage door, out of reach of
children at a minimum height of 5 feet (1.5 m), and away from ALL
moving parts of door.
NEVER permit children to operate or play with door control push
buttons or remote control transmitters.
Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
ALWAYS keep garage door in sight until completely closed. NEVER
permit anyone to cross path of closing garage door.
FOR USE WITH GARAGE DOOR OPENERS MANUFACTURED
AFTER JANUARY 1, 1995. To ensure proper functioning of your
opener, remove all old or previous push buttons/wall control
panels. Use only the enclosed door control for proper operation.
Locate the door control within sight of the door at a minimum
height of 5 feet (1.5 m) where small children cannot reach, and
away from all moving parts of the door and door hardware.
INSTALLATION
The door control is typically attached directly to the wall. For pre-
wired installations (as in new home construction) it can be
mounted to a standard single gang box.
1. Disconnect power to the garage door opener.
2. Strip 1/4" (6 mm) of insulation from one end of the bell wire
and connect to the two screw terminals on the back of the door
control as follows: red/white wire to 1 and white wire to 2.
NOTE: After installation, the indicator light behind the push
button cover will indicate proper connection.
3. Remove the push button cover by gently prying off the top edge
with a screwdriver. Fasten with 6ABx1-1/4" self-tapping screws
(standard installation) or 6-32x1" machine screws (pre-wired
installation) as follows:
(Standard Installation ONLY) Drill pilot holes and install
bottom screw, allowing 1/8"(3 mm) to protrude above the wall
surface.
• Position bottom of door control on screw head and slide
down to secure. Adjust screw for snug fit.
• Install top screw. Do NOT overtighten, you may damage the
plastic housing.
4. (Standard Installations ONLY) Run bell wire up wall and across
ceiling to motor unit. Use insulated staples to secure wire to
wall and ceiling in several places. Do NOT pierce wire with a
staple, this will create a short or open circuit.
5. Strip 7/16" (11 mm) of insulation from the end of the bell wire.
6. Connect bell wire to terminals as follows:
Quick Connect Terminals: Red/white wire to red terminal and
white wire to white (Figure 1).
Screw Terminals: Red/white to 1 and white to 2 (Figure 2).
7. Reconnect power to the garage door opener.
8. Replace the cover by inserting the bottom tabs and snapping it
into place. Test the wall control to ensure proper operation.
OPERATION
Door Control Push Button: Press to open or close the door.
Press again to reverse the door during the closing cycle, or to
stop the door while it is opening.
Light Feature: Press the Light button to switch the opener light
on or off. When the door is opened or closed, the light will remain
on for 4-1/2 minutes. Press the Light button to turn it off sooner.
The Light button will not control the opener light when the door is
in motion.
Lock Feature: Designed to prevent operation of the door from
portable remote controls. However, the door will open and close
from the Door Control push bar and from the Keylock and Keyless
Entry accessories.
To activate: Press and hold the Lock button for 2 seconds. The
push button indicator light will flash as long as the lock is on.
To turn off: Press and hold the Lock button again for 2 seconds.
The indicator light will stop flashing. Normal operation will
resume. The Lock feature will also turn off whenever the Learn
button on the opener end panel is activated.
WARNING: This product can expose you to chemicals
including lead, which are known to the State of California to
cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
Strip wire 7/16" (11 mm)
7/16" (11 mm)
Red GreyWhite
Quick-Connect
Terminals
Antenna
To release wire, push in
tab with screwdriver tip
Door Control
Connections
Push Button
Light
Button
Lock
Button
WHTRED
Bell Wire
Terminal
Screws
L
OCK
LIG HT
Opener Terminal Screws
AntennaOpener Panel
WHTRED
Bell Wire
Terminal
Screws
Push Button
Light
Button
Lock
Button
L
OCK
LIGH T
OR
)LJXUH
)LJXUH


Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: 78LM

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster 78LM stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret LiftMaster Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kramer

Kramer VP-8X8 Manual

25 November 2024
Kramer

Kramer PT-2C Manual

25 November 2024
Lazer

Lazer Bob+ Manual

25 November 2024
Dometic

Dometic DPS 80 Manual

25 November 2024
Kramer

Kramer 102MX Manual

25 November 2024
Kramer

Kramer FC-18 Manual

25 November 2024
Kramer

Kramer DSP-62-UC Manual

25 November 2024
Tiger

Tiger SKF-H101 Manual

25 November 2024