LiftMaster AELD Manual


Læs nedenfor 📖 manual på dansk for LiftMaster AELD (2 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 20 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
High Low
OFF
ON
Plug-In Loop Detector
for the OmniControl™ Board
Part # AELD
Dip Switch 1 - Sensitivity Level: n ty co d The se sitivi is ntrolle by the setting of
switc on e de ech1 ont gthe fr ed of the t tor.
Note :Chan ng t n gi he se sitivity setting automawill ti lly eset the ecca r det tor.
Cha i e fre qu t ng t t r. It is alwang ng th ency se ti w l notil rese he detecto ys eces n sary
to t the detector after changing the frequency setting by t urning the gaterese
operator power off.
Dip Switch 2 - Boost on/off:W n t tch 2 is off, t boo he he swi the sensi ivity st is
disabled. When the switch 2 is on, the t ty boost is enabled. Bo ena d sensi ivi ost ble
will inc rease the sensitivity to detect high profile vehicles.
Dip Switch 3 & 4 - Frequency: opera g equency of the det t The tin fr ec or is
con lle by se ti swi ches fro edtro d the t ng of t 3 and 4 on the nt ge of the
detector. Sometimes when buried loops are in close proximity to each other, it
may be n sar y to t d nt equ f each buried o p eces selec iffere fr encies or lo to
a op i erferen (common ca d o talk).void lo nt ce ly lle cr ss T acthe ual loo tin p o rape g
frequency is a ction size of t o the numb of s e fun of the he lo p, er turn in th
l , the g of the le - e, d e t of t eque oop len th ad in cabl an th set ing he fr ncy
swi estch (SW 3 & 4) .Theref e, setting one t or Low and the ot or de ect to her
to High may not p a separa of o pera g equency. T most rovide ny tion tin fr he
accura method of t g t o peratite se tin he ng fr equen multiple det to cy of ec rsto is
use a equ cy m er ted to the loop to actually read the opera ngfr en et co ecnn ti
frequency. The det tors fre quen ould be adjusted th at th aec cy sh so ere is
minimum of 5 kilohertz of separation t abe ween ll adjacen ops.t lo
LED Functions
– No Power
ON
– Power Applied
– No Presence
ON
– P D dresence etecte
– Loop OK
.5 Hz Flash
– Open Loop
3 Hz Flash
S r d Loopho te
Dip Switches
Dip Switch Functions
www.chamberlain.com
The FAIL” LED indicates whether or not the loop is within tolerances. If the
loop is out of tolerance, the LED indicates whether the loop circuit was
shorted (3Hz Flash) or o pen (.5 Hz Flash). When the detector is detecting a
loop failure it will force a call output and the CALL LED will be on. If the loop
problem corrects itself, the detector will begin operating normally again and
the LED will revert back to the state. Fail Off
Failed Loop Diagnostics
Mark the loop layout on the pavement. R emove sharp inside corners that
can damage the loop wire insulation.
Determin t thickn pavem o s ure that the epth of thee he ess of the ent t in d
cut o ex d t t ckn of the pavement e attemp towill n t cee he hi ess befor ting
cut the op s. Set t saw to cut a depth (typica 2" to 2.5") thatlo slot he lly
will insure a m imum 1"from tin of he top of the loop r to the pavementwi es
surface. The saw width must be larger than the diameter of the loo p wire
to avoid d amag th sulat when pla in e saw cu Cute to e wire in ion ced th t.
t o p, corn an s, and f d t R em e all ro m thehe lo er gle ee er slo s. ov debris f
saw ot sl with omp c ressed air. Che ck that the tto m of the cut smo hbo is ot
and did not break though the thickness of the pavement.
Loop Installation
1
2
FIRE
DE
PT .
SYS TEM ON
EXIT
LOO P
ALARM
SENSOR
SAFETY
LOOP
OP EN LE FT
SENSORS
COMMAND
PROCESSED
CENTE R SAFETY EXIT
13
GB
MS LINK
A
CENTER SAFETY EXIT
CENTER SAFETY EXIT
6 twists per ft from Loop
Turn e po th wer OFF to th e gate operator.
Plug i the loop det r i e re otn ecto n th desi d sl
(i.e. center, safety, exit)
Plug the rminal plug (proin te vide into ted) rminal
J8 receptacle on the botto m t oflef the
Omni board.
Bring twisted wires fr thom e loop into the proper
terminal on t
he terminal plug (i.e. center, saf y,et
exit).
Turn the power back on.
Caution:
If u mor han 1 loopsing e t
det tor, them toec set
dif fe ntre frequ .encies
(R to Dip S h 3 & 4)efer witc
1.
2.
3.
4.
5.
Plug-In Loop Detector Installation
STRIKE
OPEN
REVERSE
SENSOR
13
www.c ha mb e r
lai n .c om
detector
vehicular loop
Plug-In Loop Detector
for Liftmaster
Enabled Controllers
M EL # A EL DOD
now with B T ROLOOS CONT


Produkt Specifikationer

Mærke: LiftMaster
Kategori: Ikke kategoriseret
Model: AELD

Har du brug for hjælp?

Hvis du har brug for hjælp til LiftMaster AELD stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret LiftMaster Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024