Lightware WP-HDMI-TPS-RX97-EU Manual

Lightware AV extender WP-HDMI-TPS-RX97-EU

Læs nedenfor 📖 manual på dansk for Lightware WP-HDMI-TPS-RX97-EU (2 sider) i kategorien AV extender. Denne guide var nyttig for 3 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Quick Start Guide
WP-HDMI-TPS-RX97-EU, -EUROMOD, -UK, -US
FP-HDMI-TPS-RX97-GB3, -LEGRAND - CRFB
Further Information
The product brief and further information of this appliance is available at www.lightware.com.
See the section on the on the dedicated product page.Downloads
Contact us
sales@lightware.com
+36 1 255 3800
support@lightware.com
+36 1 255 3810
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: v1.1
19200107
Important Safety Instructions
Please read the supplied safety instruction document before using the product and keep it
available for future reference.
Introduction
WP/FP-HDMI-TPS-RX97 series twisted pair HDBaseT
TM
extenders provide
extension of uncompressed 4K/UHD video with embedded audio (up to eight
channel PCM or HBR audio) for long distances over a single CATx cable.
The thoroughly redesigned form factor of the wall and oor panels allows for easier
connecting and removing cables in narrow spaces (behind TV sets, under oor panel lids)
and reduces cable bending and breaking. The built-in cable tie-down points further ensure
stable connection and reduce cable stress.
Box Contents
Receiver unit Safety and Warranty info,
Quick Start Guide
Phoenix combicon
3-pole connector
1
Status LEDs The LEDs give feedback about the state of the unit and the
video signals. See Status LEDs for the details.
2
IR input/output 2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the
detector, IR OUT for the emitter).
3
RS-232 connector 3-pole Phoenix connector for RS-232 serial port. Firmware
upgrade can also be performed over this interface.
4
Ethernet Locking RJ45 connector for Ethernet communication.
5
HDMI output HDMI output for DVI or HDMI signal. Connect an HDMI
cable between the receiver and the display device.
6
TPS input port Locking RJ45 connector for HDBaseT
TM
signal transmission.
Connect a twisted pair cable between the transmitter and the
receiver.
7
Tie-down point The built-in tie-down points are designed to clamp the
HDMI and the CATx cable and ensure stable connection.
Please see the enlarged picture below.
Front and Rear View (WP-HDMI-TPS-RX97-US)
Connecting Steps Status LEDs
SIGNAL
OFF: no video signal transmission is present.
ON: video signal transmission is present.
LINK
OFF: TPS connection failed between the devices.
BLINKING: TPS connection is detected and Low
Power Partial Functionality (LPPF) link mode is
active.
ON: TPS connection is detected and HDBaseT
TM
(HDBT) or Long reach (LR) link mode is active.
LIVE
OFF: no power supply or out of order.
BLINKING: device is powered and ready to use.
Bottom View (WP-HDMI-TPS-RX97-US)
RS-232 Switch Modes
Please note that the 48V power adaptor is an optional accessory which can be purchased
separately.
1
RS-232 switch Normal: serial data is passed through the device.
Prog: RS-232 pass-through function is disabled, the device
is ready for the rmware upgrade (see RS-232 switch
modes section for details).
2
TPS mode switch LR: Longreach TPS mode; lower resolution (max 1080p),
longer distances.
Auto: TPS mode is determined automatically.
3
DC Input Connect the output to the 3-pole Phoenix connector on the
bottom of the wall plate.
CATx
Connect the TPS output port of the receiver to the port of the TPS+PoE
TPS-PI-1P1 by a CATx cable.
Connect the receiver (or the Matrix input board) to the power injector by a
CATx cable via the TPS port.
HDMI
Connect the sink (e.g. Projector) to the HDMI output port by HDMI cable.
RS-232
Optionally for RS-232 extension: connect a controller/controlled device
(e.g. Projector) to the RS-232 port.
IR
Optionally for Infrared extension:
Connect the IR emitter to the IR OUT port of the receiver, and/or
Connect the IR detector to the IR IN port of the receiver.
LAN
Optionally connect the receiver to a LAN.
Power
Powering on the devices is recommended to do as the nal step during
the installation. Please check the Power Supply Options section for the
details.
WP-HDMI-TPS-RX97 series have the same connectors but the dimensions are different.
The product is compatible with any HDBaseT
TM
third party devices.
HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Power Supply Options
TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -
and can receive power over the TPS line.
The extender can be powered by any of the following ways:
1. Local adaptor 2. Remote power injector 3. Matrix board
TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power
the WP-HDMI-TPS-TX/97 series and vica versa. WP-UMX-TPS-TX97 series contains PoE-
compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can be
remote powered only by each other.
Warranty void if damage occurs due to the usage of a different power source.
Typical Application
HDMI
Compatible
Transmitter or
Input Board WP-HDMI-TPS-RX97
Power adaptor IR detector Ethernet
Power LAN
RS-232
IR
WP-H DM I-T PS-R X97-US
HDMI OUTEthernet
TPS-PI-1P1
Power injector
CATxCATx
12
3
IR OUT
IR IN
LINK
TX RX
LIVE
SIGNAL
2 3 11 54
6
48V DC
Power
adaptor
TPS-PI-1P1 CATx
(TPS)
Power
send
48V DC
Power
adaptor
MX-TPS2-IB-P
DC IN
8 CH TPS INPUT BOARD WITH POE
48V 5A
- +
Ethernet
TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4
8CH INPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-IB-A
IN 1 IN 2 IN 3 IN 4
MX-TPS2-OB-S
48V 5A
DC IN
8 CH TPS OUTPUT BOARD WITH DIGITAL AUDIO
12V power on TPS c
12V power on TPS c
TPS OUT 1 TPS OUT 2 TPS OUT 3 TPS OUT 4
8CH OUTPUT BOARD FOR HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-OB-A
OUT 1 OUT 2
CATx
(TPS)
External
power supply
Power send
T
ypical: 0.5A
Max: 1.25A
- +
Max:2.5A
mm2 :NIP
IR OUT
IR IN
LINK
TX RX
LIVE
SIGNAL
WP-HDM I- TP S-RX 97-US
HD MI OUTEthern et
IR OUT
IR IN
LINK
TX RX
LIVE
SIGNAL
WP-HDM I- TP S-RX 97-US
HD MI OUTEthern et
IR OUT
IR IN
LINK
TX RX
LIVE
SIGNAL
WP-HDM I- TP S-RX 97-US
HD MI OUTEthern et
Compatible Devices
TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90
series.
IR cable
Serial
cable
IR emitter
HDMI
Blu-Ray or DVD Player
LAN
Ethernet switch
HD Projector
Touch panel
Sn:
Made in EU, H ungary
RoHS
Ethernet 10/100
Bidir ectional IR
Bidir ectional RS-232
TTPPSS LLoonngg DDiissttaannccee TTrraannssmmiitttteerr
HDMI, 3D, 4K suppor ted
For best performance use AW G23 CAT6 o r CAT 7 SFTP cable
PIN: 2 mm
12V 1A DC
H
D
M
I--T
PS --T
X97
Device can be remote po wered over TPS link with PoE
(IEEE 802.3af)
TPS OUT PoE( )
TPS-PI-1P1
LAN
HDMI-
TPS-TX97
48V DC
Power
adaptor
LAN
IR detector
HDMI
IR cable
Serial cable
ETHE RNET
Laptop
WP-HDMI-TPS-RX97-US
Typical: 0.5A
Max: 1.25A
- +
Max:2.5A
mm2 :NIP
IR OUT
IR IN
LINK
TX RX
LIVE
SIG NAL
WP-HDM I-TPS-RX97-US
HDMI OUTEtherne t
CATx
TPS connection
CATx up to 170m
Power
send
7
WP-HDMI-TPS-RX97-US
HDMI OUTEthernet
Wiring Guide for RS-232 Data Transmission
WP/FP-HDMI-TPS-RX97 series are built with 3-pole Phoenix connector. See the below
examples of connecting to a DCE (Data Circuit-terminating Equipment) or a DTE (Data
Terminal Equipment) type device:
Lightware device and a DCE
D-SUB 9 - Phoenix
Lightware device and a DTE
D-SUB 9 - Phoenix
1
6
9
5
2: TX data transmit
3: RX data receive
TX RX
1
69
5
2: TX data receive
3: RX data transmit
5: Ground
For more information about the cable wiring see the users manual of the device or
Cable Wiring Guide on our website www.lightware.com/support/guides-and-white-papers.
LINKLIVE
SIGNAL
LINKLIVE
SIGNAL
LINKLIVE
SIGNAL
Safety and
Warranty
Info
Quick
Start
Guide
IR IN
SIGNAL
HDMI OUT


Produkt Specifikationer

Mærke: Lightware
Kategori: AV extender
Model: WP-HDMI-TPS-RX97-EU

Har du brug for hjælp?

Hvis du har brug for hjælp til Lightware WP-HDMI-TPS-RX97-EU stil et spørgsmål nedenfor, og andre brugere vil svare dig




AV extender Lightware Manualer

AV extender Manualer

Nyeste AV extender Manualer