Lightware WP-HDMI-TPS-TX97-EU Manual

Lightware AV extender WP-HDMI-TPS-TX97-EU

Læs nedenfor 📖 manual på dansk for Lightware WP-HDMI-TPS-TX97-EU (2 sider) i kategorien AV extender. Denne guide var nyttig for 6 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
Quick Start Guide
WP-HDMI-TPS-TX97-EU, -EUROMOD, -UK, -US
FP-HDMI-TPS-TX97-GB3, -LEGRAND, -CRFB
Further Information
The product brief and further information of this appliance is available at www.lightware.com.
See the section on the dedicated product page. Downloads
Contact Us
sales@lightware.com
+36 1 255 3800
support@lightware.com
+36 1 255 3810
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: v1.2
19200108
Important Safety Instructions
Please read the supplied safety instruction document before using the product and keep it
available for future reference.
Introduction
WP/FP-HDMI-TPS-TX97 series twisted pair HDBaseT
TM
extenders provide
extension of uncompressed 4K/UHD video with embedded audio (up to eight
channel PCM or HBR audio) for long distances over a single CATx cable.
The thoroughly redesigned form factor of the wall and oor panels allows for easier
connecting and removing cables in narrow spaces (behind TV sets, under oor panel lids)
and reduces cable bending and breaking. The built-in cable tie-down points further ensure
stable connection and reduce cable stress.
Box Contents
Transmitter unit Safety and Warranty info,
Quick Start Guide
Phoenix combicon
3-pole connector
1
Status LEDs The LEDs give feedback about the state of the unit and the
video signals. See Status LEDs for details.
2
IR input/output 2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the
detector, IR OUT for the emitter).
3
RS-232 connector 3-pole Phoenix connector for RS-232 serial port. Firmware
upgrade can also be performed over this interface.
4
Ethernet Locking RJ45 connector for Ethernet communication.
5
HDMI input Input for a digital video source. Applied cable shall not be
more, than 20 m (at 1080p) and 5 m (at 4K).
6
TPS output port Locking RJ45 connector for HDBaseT
TM
signal transmission.
Connect a twisted pair cable between the transmitter and the
receiver.
7
Tie-down point The built-in tie-down points are designed to clamp the
HDMI and the CATx cable and ensure stable connection.
Please see the enlarged picture below.
Front and Rear View (WP-HDMI-TPS-TX97-US) Bottom View (WP-HDMI-TPS-TX97-US)
RS-232 Switch Modes
Please note that the 48V power adaptor is an optional accessory which can be purchased
separately.
1
RS-232 switch Normal: serial data is passed through the device.
Prog: RS-232 pass-through function is disabled, the device
is ready for the rmware upgrade (see RS-232 switch
modes section for details).
2
TPS mode switch LR: Longreach TPS mode; lower resolution (max 1080p),
longer distances.
Auto: TPS mode is determined automatically.
3
DC Input Connect the output to the 3-pole Phoenix connector on the
bottom of the wall plate.
WP-HDMI-TPS-TX97 series have the same connectors but the dimensions are different.
Connecting Steps
CATx
Connect the TPS output port of the transmitter to the TPS+PoE port of the
TPS-PI-1P1 by a CATx cable.
Connect the receiver (or the Matrix input board) to the power injector by a
CATx cable via the TPS port.
HDMI
Connect the source (e.g. Blu-ray player) to the HDMI input port by HDMI cable.
RS-232
Optionally for RS-232 extension: connect a controller/controlled device
(e.g. Touch panel) to the RS-232 port.
IR
Optionally for Infrared extension:
Connect the IR emitter to the IR OUT port of the transmitter, and/or
Connect the IR detector to the IR IN port of the transmitter.
LAN
Optionally connect the transmitter to a LAN.
Power
Powering on the devices is recommended to do as the nal step during
the installation. Please check the Power Supply Options section for the
details.
Power Supply Options
TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -
and can receive power over the TPS line.
The extender can be powered by any of the following ways:
1. Local adaptor 2. Remote power injector 3. Matrix board
TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power
the WP-HDMI-TPS-TX/97 series and vica versa. WP-UMX-TPS-TX97 series contains PoE-
compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can be
remote powered only by each other.
Warranty void if damage occurs due to the usage of a different power source.
The product is compatible with any HDBaseT
TM
third party devices.
HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Compatible Devices
TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90
series.
Status LEDs
SIGNAL
OFF: no video signal transmission is present.
ON: video signal transmission is present.
LINK
OFF: TPS connection failed between the devices.
BLINKING: TPS connection is detected and Low
Power Partial Functionality (LPPF) link mode is
active.
ON: TPS connection is detected and HDBaseT
TM
(HDBT) or Long reach (LR) link mode is active.
LIVE
OFF: no power supply or out of order.
BLINKING: device is powered and ready to use.
Typical Application
12
3
IR OUT
IR IN
LINK
TX RX
LIVE
SIGNAL
2 3 11 54
6
LINKLIVE
SIGNAL
LINKLIVE
SIGNAL
LINKLIVE
SIGNAL
48V DC
Power
adaptor
TPS-PI-1P1 CATx
(TPS)
Power
send
48V DC
Power
adaptor
MX-TPS2-IB-P
DC IN
8 CH TPS INPUT BOARD WITH POE
48V 5A
- +
Ethernet
TPS IN 1 TPS IN 2 TPS IN 3 TPS IN 4
8CH INPUT BOARD FO R HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-IB-A
IN 1 IN 2 IN 3 IN 4
MX-TPS2-OB-S
48V 5A
DC IN
8 CH TPS OUTPUT BOARD WIT H DIGITAL AUDIO
12V power on TPS c
12V power on TPS c
TPS OU T 1 TPS OUT 2 TPS OUT 3 TPS OUT 4
8CH OUTPUT BOARD FO R HDMI WITH 3D AND ANALOG AUDIO
MX-HDMI-3D-OB-A
OUT 1 OUT 2
CATx
(TPS)
External
power supply
Power send
T
ypical: 0.5A
Max: 1.25A
- +
Max:2.5A
mm2 :NIP
IR OUT
IR IN
LINK
TX RX
LIVE
SIGNAL
WP-HDM I- TP S-T X 97-US
HD MI INEthern et
LINK
TX RX
LIVE
SIGNAL
WP-HDM I- TP S-T X 97-US
HD MI INEthern et
LINK
TX RX
LIVE
SIGNAL
WP-HDM I- TP S-T X 97-US
HD MI INEthern et
IR OUT
IR IN
IR OUT
IR IN
WP-HDMI-TPS-TX97
Power adaptorEthernet
IR emitter
Touch panel
IR
RS-232 LAN Power
HDMI
Compatible
Receiver or
Output Board
TPS-PI-1P1
Power injector
WP-HDM I-TPS-TX97-US
HDMI INEther net
CATx
CATx
7
IR cable
Serial cable
TPS connection
CATx up to 170m
HDMI-TPS-RX97
IR detector
HD Projector
Sn:
Made in EU, Hungary
RoHS
Ethernet 10/100
Bid irectional IR
Bid irectional RS-232
HDM I, 3D, 4K supp orted
HH DDMMII--TT PPSS--RRXX9977
Sn:
TTPPSS LLoonngg DDii ssttaannccee RReecceeiivveerr
PIN: 2mm
12V 1A DC
For best performance use AWG23 CAT6 or CAT7 SFTP cable
Device can be remote powered over TPS link with PoE
(IEEE 802.3af)
TPS I N
PoE( )
TPS-PI-1P1
48V DC
Power adaptor
Blu-Ray or
DVD Player
Touch panel
Ethernet switch
Serial
cable
HDMI
IR cable
LAN
WP-HDMI-
TPS-TX97-US
CATx
Power
send
Ty pical: 0.5A
Max: 1.25A
- +
Max:2.5 A
mm2 :NIP
HDMI
IR emitter
IR IN
IR OUT
LINK
TX RX
LIVE
SIG NAL
WP-HDMI-TPS-TX97-US
HDMI INEthernet
48V DC
Power
adaptor
Wiring Guide for RS-232 Data Transmission
WP/FP-HDMI-TPS-RX97 series are built with 3-pole Phoenix connector. See the below
examples of connecting to a DCE (Data Circuit-terminating Equipment) or a DTE (Data
Terminal Equipment) type device:
Lightware device and a DCE
D-SUB 9 - Phoenix
Lightware device and a DTE
D-SUB 9 - Phoenix
TX RX
1
6
9
5
2: TX data transmit
3: RX data receive
5: Ground
TX RX
1
69
5
2: TX data receive
3: RX data transmit
5: Ground
For more information about the cable wiring see the users manual of the device or
Cable Wiring Guide on our website www.lightware.com/support/guides-and-white-papers.
Safety and
Warranty
Info
Quick
Start
Guide
IR IN
SIGNAL
HDMI OUT


Produkt Specifikationer

Mærke: Lightware
Kategori: AV extender
Model: WP-HDMI-TPS-TX97-EU

Har du brug for hjælp?

Hvis du har brug for hjælp til Lightware WP-HDMI-TPS-TX97-EU stil et spørgsmål nedenfor, og andre brugere vil svare dig




AV extender Lightware Manualer

AV extender Manualer

Nyeste AV extender Manualer