Livex Lighting Brussels 47070-08 Manual

Livex Lighting Lys Brussels 47070-08

Læs nedenfor 📖 manual på dansk for Livex Lighting Brussels 47070-08 (2 sider) i kategorien Lys. Denne guide var nyttig for 5 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/2
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the installation
instructions do apply to this product.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1).
1. Shut off the power at the circuit breaker and remove old fixture from ceiling,
including the old mounting plate.
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Attach the mounting plate (A) to the junction box using screws (B). The side of
the mounting plate marked “GND” must face out. The junction box is not
included.
4. While holding the lamp body towards the junction box, guide supply wires
through hole in center of mounting plate. Follow wiring instructions carefully
(see fig.2).
5. Put the lamp body onto the ceiling, aligning the screws on the mounting plate with
the mounting holes on the canopy (C). Lock it securely with the nuts (D).
6. Attach the glass shade (E) and the nut (F) onto the socket of the lamp body, then
securely tighten the nut (F) using the wrench (G), then remove the socket wrench
and save it.
7. Install the light bulb (Not included) in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
CONNECTING THE WIRES (Fig.2)
1. Take the black wire from the ceiling junction box and the black wire from the
fixture and twist bare ends together. Twist wire connector onto end of wire until
snug.
2. Repeat same process with white junction box wire and white fixture wire. NOTE:
Twist wires together in the same direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper), attach this wire
and the bare copper wire from the fixture together as step 1. If junction box has
no ground wire, attach the bare copper fixture wire to the green ground screw on
the mounting plate.
4. Tuck the wire connections neatly into the junction box.
Your installation is now complete. Return power to the junction box and test
the fixture.
FIG.1
FIG.2
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black (Hot)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper (Ground)


Produkt Specifikationer

Mærke: Livex Lighting
Kategori: Lys
Model: Brussels 47070-08

Har du brug for hjælp?

Hvis du har brug for hjælp til Livex Lighting Brussels 47070-08 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys Livex Lighting Manualer

Lys Manualer

Nyeste Lys Manualer

Sigma

Sigma EOX FL 150 Manual

23 December 2024
Nanlite

Nanlite D672BII Manual

19 December 2024
Nanlite

Nanlite Compac 40 Manual

19 December 2024
Nanlite

Nanlite MixPad II 11C Manual

18 December 2024
Nanlite

Nanlite D672II Manual

18 December 2024
Chauvet

Chauvet WELL POD 2X6 Manual

17 December 2024
Luxli

Luxli ORC-VIOLA-M2 Manual

17 December 2024
Makita

Makita DML817 Manual

16 December 2024