Livex Lighting Coronado 6109-91 Manual

Livex Lighting Lys Coronado 6109-91

Læs nedenfor 📖 manual på dansk for Livex Lighting Coronado 6109-91 (1 sider) i kategorien Lys. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/1
ASSEMBLING & INSTALLATION INSTRUCTIONS PRODUCT# 6109
For Flush Mount Ceiling Fixtures
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .
MOUNTING THE FIXTURE (Fig.1)
1. Shut off the power at the circuit breaker box. Remove old
fixture and all hardware from Junction Box.
2. Carefully unpack your new fixture and lay out all the parts
on a clear area. Take care not to lose any small parts
necessary for installation.
3. Thread the two Studs (A) about 1/4”into the pre-drilled
holes in the Mounting strap spaced the same distance apart
as the holes in the fixture body(B).
4. Attach the Mounting strap to the Junction Box with the two
Junction Box Screws as shown. The side of the Mounting
strap marked "GND" must face out.
5. While holding the column assembly towards the ceiling,
connect the electrical wires as Shown in Fig.2, making
sure that all wire nuts are secured. You may have to wrap
the connections with electrical tape. If your outlet has a
ground wire (green or bare copper), connect the fixture
ground wire to it. Otherwise connect fixtures ground wire
directly to the Mounting strap with the green screw
provided. After wires are connected, tuck them carefully
inside the Junction Box.
6. Put fixture body (B) onto the junction box, aligning screws
on mounting strap with mounting holes in canopy and lock
it securely with the ball nuts(I).
7. Thread end of pipe nipple (D) into the hex nut(G). Raise the
pipe nipple assembly and shim into the glass(C) and through
the hole. Attach cover(E) onto the glass(C) and lock it with
the ball nut(F).
8. Install the light bulbs in accordance with the fixtures
specifications.NOTE: DO NOT EXCEED THE
SPECIFIED WATTAGE.
9. Raise the glass(C) to the fixture body (B), then fasten the
arm's hook, aligning holes in the glass(C) and lock it with
the knob(H).
Your installation is now complete. Return power to the
junction box and test the fixture.
Fig.1
Fig.2
MIN 90℃ SUPPLY CONDUCTORS
White or
HOUSE
Black
WIRES
(Hot)
Smooth
FIXTURE
WIRES
Black or
Ribbed
WIRES
FIXTURE
Bare Copper(Ground)
FIXTURE
WIRES
Copper
(Ground)
HOUSE
(Neutral)
WIRES
White
Bare
Green or
WIRES
HOUSE


Produkt Specifikationer

Mærke: Livex Lighting
Kategori: Lys
Model: Coronado 6109-91

Har du brug for hjælp?

Hvis du har brug for hjælp til Livex Lighting Coronado 6109-91 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Lys Livex Lighting Manualer

Lys Manualer

Nyeste Lys Manualer

Sigma

Sigma EOX FL 150 Manual

23 December 2024
Nanlite

Nanlite D672BII Manual

19 December 2024
Nanlite

Nanlite Compac 40 Manual

19 December 2024
Nanlite

Nanlite MixPad II 11C Manual

18 December 2024
Nanlite

Nanlite D672II Manual

18 December 2024
Chauvet

Chauvet WELL POD 2X6 Manual

17 December 2024
Luxli

Luxli ORC-VIOLA-M2 Manual

17 December 2024
Makita

Makita DML817 Manual

16 December 2024